在柔性变焦系统中的压力变焦镜

从理论上和实验上对水冷镜的镜面曲率半径随压力变化的规律作了研究。对压力变形后镜面相对于球面作了波像差分析，分析表明压力变焦镜用于中红外激光系统是合适的     

Reticulated Porous Multiphase Ceramics with Improved Compressive Strength and Fracture Toughness

A multiphase reticulated porous ceramic (RPC) as Si₃N₄–Al₂O₃–SiO₂ was fabricated by replication techniques. Proper volumes of additives and twice sinter- twice immerse process endow the RPC an excellent crack healing and submerging property. The compressive strength and fracture toughness improved owing to the crack bridging behavior. The existence of pores in struts in RPC blunt the crack tip and increased the external force needed to propagate the crack. The mechanisms play a beneficial role in enhancing the compressive strength and fracture strength. Si₃N₄ RPC with additives of 5%Al and 5% Al₂O₃ yielded the compressive strength of 9.8 MPa and fracture toughness of 0.3 MPa m^1/2.     

阜新市细河改造工程坝基渗漏计算及处理效果分析

阜新市细河改造工程由四座橡胶坝和两岸防洪大堤组成，由于堤(坝)基第四系冲洪积层广泛发育，存在渗漏同题。合理选择施工处理方案，是工程成功的关键。作者根据场区不同的地质条件环境条件采取有针对性的不同处理方案，既解决了防渗问题又缩短了施工工期，降低工程造价，取得了很好的经济效益和社会效益。     

浅析分户供热的计量

本文介绍了国外在供热分户计量方面的测定原理、手段和设备,费用分配原则,仪表与系统的配合和安装方式,并就其与国内系统的配合提出了建议。     

Numerical Filling Simulation of Injection Molding Using Three-Dimensional Model

1 Introduction During injection moulding, the rheological response of polymer melts is generally non-Newtonian and nonisothermal with the position of the moving flow front. Because of these inherent factors, it is difficult to analyze the filling process. Therefore, simplifications usually are used. For example, in middle-plane technique and dual domain technique [1], because the most injection molded parts have the characteristic of being thin but generally of complex shape, the Hele-Shaw …     

排列互比法用于超精测角的研究

作者分析了我互比法现行的两种数据处理方法的缺点，提出了应用最小二乘法原理推导出合理的数据处理方法。本文还首次从理论上阐明了排列互比法测量结果中出现一次谐波系统误差的原因，提出了减少和消除这一些系统误差的方法，并给实验验证。     

Two dimensional deformation characteristics of bloom CC with liquid core reduction

A two-dimensional model was applied to simulate the liquid core reduction(LCR) technology of bloom CC using ANSYS software.The deformation characteristics of bloom under different liquid fraction and reducing amount are obtained.The results indicate that the main deformation condition of bloom shell is compressive strain,mainly undertaken by the liquid core,which increases with the enhancement of reducing amount.Solidified shell takes minor deformation.The longitudinal section of bloom appears sunken and the narrow side bulges,which grow serious when the liquid fractionincreases.     

Ornithine decarboxylase transformation of NIH/3T3 cells is mediated by altered epidermal growth factor receptor activity

Ornithine decarboxylase (ODC) has been shown to be oncogenic in transfected NIH/3T3 cells overexpressing the enzyme from a heterologous promoter. These cells, designated as NODC-2 cells, acquire proliferative properties associated with tumorigenic transformation such as loss of contact inhibition, decreased population doubling time, anchorage-independent growth, and tumor production in nude mice. At least one of these parameters, loss of contact inhibition, remains dependent on elevated ODC levels. We have used these cells to investigate the molecular mechanisms by which ODC overexpression drives cell transformation and to examine the involvement of other proto-oncogene products in this process. An interaction between ODC overexpression and the epidermal growth factor receptor (EGF-R) was suggested initially by the elevation of both basal (300%) and ligand-induced (457%) EGF-R tyrosine kinase activities in NODC-2 cells compared to similarly treated control NLK cells. Disruption of EGF-R mediated signal transduction in NODC-2 cells both by treatment with tyrphostin-25 or by transfection with a vector expressing a dominant negative EGF-R mutant resulted in reacquisition of contact-inhibited growth and suppression of anchorage-independent, clonogenic growth in soft agar. We conclude that ODC-induced transformation of NIH/3T3 cells is mediated, at least partly, by alterations in EGF-R signal transduction activity.     

轴齿轮断齿失效分析

通过对轴齿轮断口形貌、硬度测试及金相组织等试验进行分析表明，齿根处没有进行硬化处理造成齿根处抗疲劳性能不足是导致轴齿轮疲劳断裂的主要原因，另外齿根过渡处倒角过小，且存在纵向刀痕引起了较大应力集中也是导致轴齿轮疲劳断裂的原因。