Effects of grain sizes, shapes, and distribution on minimum sizes of representative volume elements of cubic polycrystals

In the literature the concept of representative volume element (RVE) was introduced to correlate the effective or macroscopic properties of materials with the properties of the microscopic constituents and microscopic structures of the materials. However, to date little quantitative knowledge is available about minimum RVE sizes of various engineering materials. In our recent paper [J. Mech. Phys. Solids 50 (2002) 881], a new definition of minimum RVE size was introduced based on the concept of nominal modulus. Numerical experiments using the finite element method (FEM) were then carried out for determining the minimum RVE sizes of more than 500 cubic polycrystals in the plane stress problem, under the assumption that all grains in a polycrystal have the same square shape––called the simple polycrystal model. The major finding is that the minimum RVE sizes for effective elastic moduli have a roughly linear dependence on crystal anisotropy degrees. The present paper takes into account the effect of grain sizes, shapes, and distribution on the minimum RVE sizes for real cubic polycrystals that are formed by crystallization processes. Similar roughly linear dependence is found again, with the slope about 19% lower than that in the simple polycrystal model. This finding is interesting and useful because numerical experiments on minimum RVE sizes for a large number of crystals are quite time-consuming and the simple polycrystal model reduces significantly the FEM pre- and post-processing works. This should be particularly true in numerically testing minimum RVE sizes for three-dimensional polycrystals and for nonelastic properties in future works. With a maximum relative error 5%, all the polycrystals tested have a minimum RVE size of 16 or less times the grain size.     

MIMO系统中简单的扩展空时块编码分集技术研究

本文提出一种多输入多输出（MIMO）天线系统中简单的扩展空时块编码（SSTBC）分集技术，采用沃尔什码来区分各天线发送数据子流。采用这种方法，在系统带宽一定时，不降低发送信息速率，同时接收机简单。不同天线的发送信息经过了所有收一发天线对之间的空间子信道，获得了所有路径的部分空间分集增益，仿真结果表明，这种增益的获得不受限于接收分集阶数，并且随发射天线的增加以一定的线性关系增加。     

Enhanced light output in nitride-based light-emitting diodes by roughening the mesa sidewall

In this letter, we will report on a nitride-based light emitting diode with a mesa sidewall roughening process that increases light output power. The fabricated GaN-based light-emitting diode (LED) wafers were first treated through a photoelectrochemical (PEC) process. The Ga/sub 2/O/sub 3/ layers then formed around the GaN : Si n-type mesa sidewalls and the bottoms mesa etching regions. Selective wet oxidation occurred at the mesa sidewall between the p- and the n-type GaN interface. The light output power of the PEC treated LED was seen to increase by about 82% which was caused by a reduced index reflectance of GaN-Ga/sub 2/O/sub 3/-air layers, by a rough Ga/sub 2/O/sub 3/ surface, by a microroughening of the GaN sidewall surface, and by a selective oxidation step profile of the mesa sidewall that increases the light-extraction efficiency from the mesa sidewall direction. Consequently, this wet PEC treated process is suitable for high powered nitride-based LEDs lighting applications.     

Stimulation of negative magnetoresistance by an electric field and light in silicon doped with boron and manganese

It is experimentally ascertained that light stimulates the negative magnetoresistance observed in a high electric field in silicon doped with boron and manganese. The optimum conditions (the electric field, temperature, illumination, and resistivity of the material) for observation of the largest magnitude of negative magnetoresistance in (Si:B):Mn are determined. The dependence of the negative magnetoresistance on the concentration of compensating impurity is established.     

Generalized difference control of parallel streams temperatures

A furnace with multiple parallel passes and multiple burners is commonly seen in petroleum refineries. In order to maintain the furnace running in a safe, stable, and high-efficiency state it is necessary to control the outlet temperatures of the multiple passes to be the same. Due to the fact that the process of the oil heating in such furnace is nonlinear, multivariable, time varying, has serious coupling among passes, has frequent dynamic changes and a large time delay, traditional control methods have trouble in controlling these temperatures, and some advanced control methods, including predictive control, adaptive control, and robust control, are usually too complex for convenient use. In this paper, a control technique, called differences control technique (DsCT), is proposed to distribute the stream flowrates such that the stream temperatures are as identical as possible. The principle of the proposed technique is explained and demonstrated, and the results of its application to a real-life petroleum refinery furnace are also reported. The DsCT technique has the following advantages: it does not need complicated design procedures, the controller structure is simple, it is easy to apply, and it can be canonically applied to furnaces with different number of passes.     

Influence of the preparation conditions on the size and morphology of nanocrystalline lanthanum orthoferrite

Nanocrystalline LaFeO₃ is prepared by the dehydration of coprecipitated lanthanum and iron(III) hydroxides. It is shown that the behavior of the samples during heating and the size distribution of LaFeO₃ nanocrystals can be considerably different depending on the scheme used for coprecipitation of lanthanum and iron hydroxides; independently of the method employed for coprecipitation of the initial compounds, sintering of the samples at 950°C leads to the formation of lanthanum orthoferrite crystals up to 100 nm in size.     

Synthesis of polyanilines with pendant fluorescent units

Functionalized polyanilines containing biphenyl, terphenyl, carbazole, anthracene, and 4-n-hexylphenyl moieties were synthesized though the reaction of polyaniline in emeraldine base form with sodium salt of corresponding vinylketoaromatics with quantitative yields. Polymers were characterized with Fourier transform infrared spectroscopy, proton nuclear magnetic resonance spectroscopy, and thermogravimetry. The emission characteristics of these polymers in N-methyl-2-pyrrolidone solution were examined. The functionalized polyanilines exhibited an intense green emission.     

Protoplast from <Emphasis Type="Italic">β</Emphasis>-carotene-producing fungus <Emphasis Type="Italic">Blakeslea trispora</Emphasis>: Preparation,regeneration and validation

The effects of key parameters on the preparation and regeneration of protoplast from the β-carotene-producing fungus Blakeslea trispora were discussed in this paper, including the combination of various enzymes, mycelial age, digesting time and temperature, pH value, osmotic stabilizers, pretreatment, culture medium and culture method. Under the condition of mixed enzymes in osmotic stabilizer (0.6 M NaCl) combined with 2% lysozyme, 3% cellulase and 3% snailase, the highest protoplast yield, as high as 7.48×106 protoplasts/mL, was obtained when mycelial age was 60 h at pH 5.0–6.0 with digesting for 14–16 h at 28 °C. After purification of the obtained protoplasts, they were regenerated in PDA regenerative medium using bilayer plate culture method. To validate the usability of the protoplasts, a novel plasmid with green fluorescent protein (GFP) was used in transformation for easy visual observation. The results showed that the protoplasts prepared by the optimized method were active and applicable in further gene manipulation experiments. This work was presented at 13 ^th YABEC symposium held at Seoul, Korea, October 20–22, 2007.     

Onset of buoyancy-driven convection in melting from below

When a horizontal homogeneous solid is melted from below, convection can be induced in a thermally unstable melt layer. In this study the onset of buoyancy-driven convection during time-dependent melting is investigated by using similarly transformed disturbance equations. The critical Rayleigh numbers based on the melt-layer thickness are found numerically for various conditions. For small superheats, the present predictions approach the well known results of classical Rayleigh-Bénard problems, that is, critical Rayleigh numbers are located between 1,296 and 1,708, regardless of the Prandtl number. However, for high superheats the critical Rayleigh number increases with an increase in phase change rate but with decrease in Prandtl number.