PMMA tacticity and alumina powder dispersion stability

Summary Sedimentation experiments and X-ray photoelectron spectroscopy (XPS or ESCA) analyses have been used to study the effect of poly(methylmethacrylate) (PMMA) tacticity on aluminum oxide powder dispersion stability in a common solvent medium. The relative trends from sedimentation densities, and from surface analyses after solvent washing show that (PMMA) adsorption is greatest with isotactic polymer, where isotactic>atactic>syndiotactic adsorption. These results suggest that surface adsorption and hence dispersion stability can be influenced by polymer chain configuration as well as by chain conformation.     

Selective hydrogenation of oleic acid to 9-octadecen-1-ol: Catalyst preparation and optimum reaction conditions

A new catalyst, ruthenium-tin-alumina is found to selectively hydrogenate oleic acid to 9-octadecen-1-ol (oleyl + elaidyl alcohol) at low pressure with high yield. Catalyst preparation methods, catalyst raw materials and activation conditions have a significant effect on the activity of the catalyst. The optimum atomic ratio of ruthenium to tin is about 1:2. Catalyst prepared by an improved sol-gel method shows higher activity and selectivity than catalysts prepared by impregnation and coprecipitation methods. Chloride is found to have a negative effect on catalytic activity. The best catalyst is prepared from chloride-free ruthenium and tin raw materials. Under the optimum reaction conditions of 250°C and 5.6 MPa, the selectivities for 9-octadecen-1-ol and total alcohol (9-octadecen-1-ol + stearyl alcohol) formation are 80.9% and 97%, respectively, at a conversion of 81.3%.     

Significance of DNA ploidy in the treatment of T1 glottic carcinoma

OBJECTIVE: To assess the role of DNA ploidy as a predictor of radioresistance in T1 glottic carcinoma. DESIGN: Case-control study. Flow cytometric DNA ploidy measurements were performed on formalin-fixed paraffin-embedded tumor specimens from 15 patients with T1 glottic laryngeal carcinomas in whom radiotherapy had failed and from a matched group of 15 patients in whom an identical radiotherapy regimen was curative. Analysis of DNA content was performed blind to outcome of treatment. SETTING: Academic tertiary referral medical center. PARTICIPANTS: Thirty patients with clinically staged T1, N0, M0 glottic carcinoma. INTERVENTION: All patients received radiation to the larynx through opposed lateral ports at a total dose of 64 to 70 Gy. RESULTS: Ten diploid and five aneuploid histograms were found in the resistant group, and six diploid and nine aneuploid histograms were found in the radiosensitive group. This difference was not statistically significant. A trend toward a higher relapse rate after radiotherapy (62.5%) among patients with diploid tumor compared with those with aneuploid tumor (35.7%) was noted. CONCLUSIONS: DNA ploidy did not predict response to radiotherapy in patients with T1 glottic cancer, probably because of the small number of patients. A trend toward lower risk of local recurrence after radiotherapy in aneuploid tumors was noted. A larger prospective study is needed to assess the value of DNA ploidy in the treatment of early laryngeal cancer.     

Is it opened or closed? Colombian science on the move

Using recent original data from three different sources, the article exhibits some strengths and weaknesses of science in Colombia. It shows that research in this country is in a process of growth although recent results of this positive trend are still to be confirmed. Comparing the evolution of science in Colombia with that of Latin America as a whole, describing and explaining its geographical and institutional concentration as well as its thematic distribution, it also reveals the interdependance between science production dynamics and international cooperation programmes. A basic argument is that the development of science in this country, even though it is fragile and erratic, does not lack sound bases. The indicators used suggest indeed an autonomous scientific motion and inspiration which does not contradict the internationalization process of Colombian science but rectifies the picture of an excessively isolated or dependent community that used to be portrayed.     

Effect of magnesium content on the ageing behaviour of water-chilled Al-Si-Cu-Mg-Fe-Mn (380) alloy castings

A study of the effect of magnesium concentration on the ageing behaviour as measured by the hardness of 380 alloy was conducted for three levels of magnesium, namely 0.06 (base alloy), 0.33 and 0.5 wt%, for water-chilled castings (dendrite arm spacing ∼ 10–15 μm). Differential scanning calorimetry analysis of as-cast samples was carried out to determine the changes in the reactions of the phases obtained during alloy solidification, employing heating rates of 0.1 and 1.0°Cs⁻¹, up to approximately 700°C. Two heat treatments were applied to the as-cast alloys: T5 comprising ageing at 25 (room temperature), 155, 180, 200 and 220°C, for times up to 200 h, and T6 comprising solution heat treatment at 480 °C or 515°C for 8 h, followed by quenching in warm water at 60°C, followed by immediate artificial ageing at 155 or 180°C for varying times up to 100h. The results show that the higher hardness values obtained with T6 treatment can be explained by the excess precipitation of magnesium-containing phases in the as-solidified alloys. This precipitation could be eliminated under the high cooling-rate conditions prevalent in die-casting operations so that T5 treatment may be used to replace T6 treatment to produce the same hardness values. In addition, solution heat treatment in the low-temperature range (480–515°C) is adequate to produce the required changes in silicon morphology and dissolution of magnesium in the matrix. No significant difference in hardness behaviour was observed when the magnesium content was increased beyond 0.3 wt%.     

Traction-based Completed Adjoint Double Layer Boundary Element Method in elasticity

This paper is concerned with a traction-based Completed Adjoint Double Layer Boundary Element Method to solve for the surface traction of a system of rigid particles embedded in an elastic matrix. The main feature of the method is a single layer representation of the displacement field, which leads to a system of second-kind integral equations for the traction field, the extreme eigenvalue of which could be deflated, allowing iterative solution strategies to be effectively applied. The method is therefore most suitable for large-scale simulations of particulate solids. The method is benchmarked against some known analytic solutions, including the difficult stress singularity problems at sharp edges. The effectiveness of the method in dealing with a large number of inclusions is also demonstrated with an elongational deformation problem involving up to 25 inclusions.Research supported by the Australian Research Council (to NP-T and X-JF) and the National Natural Science Foundation of China (X-JF).     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.