Modeling and verification of the double frequency effect using a MEMS device

The derivation, verification, and implication of the nonlinear dynamic and frequency response of electrostatic actuator due to the double frequency effect (DFE) were reported in this study. In particular, an extra mode called half mode was observed and measured in various studies. However, a complete in-depth discussion of the effect was not reported in the past. In the present study, a second-order dynamical equation was adapted firstly to model the dynamic and frequency response of electrostatic actuator where typical harmonic input signal with a dc bias was used. Secondly, by solving the equation, complex waveform in dynamic response and an extra half mode in frequency response due to the double frequency effect can be observed and discussed. To verify the simulated result, an electrostatic driving device was fabricated using PolyMUMPS^© process. Note that in frequency response, when dc bias is equal to the amplitude of ac signal, simulated and experimental results indicated that the amplitude of half mode was one-fourth of first mode.     

Colloidal Synthesis of Hollow Cobalt Sulfide Nanocrystals

Formation of cobalt sulfide hollow nanocrystals through a mechanism similar to the Kirkendall Effect has been investigated in detail. It is found that performing the reaction at > 120 °C leads to fast formation of a single void inside each shell, whereas at room temperature multiple voids are formed within each shell, which can be attributed to strongly temperature‐dependent diffusivities for vacancies. The void formation process is dominated by outward diffusion of cobalt cations; still, the occurrence of significant inward transport of sulfur anions can be inferred as the final voids are smaller in diameter than the original cobalt nanocrystals. Comparison of volume distributions for initial and final nanostructures indicates excess apparent volume in shells, implying significant porosity and/or a defective structure. Indirect evidence for fracture of shells during growth at lower temperatures was observed in shell‐size statistics and transmission electron microscopy images of as‐grown shells. An idealized model of the diffusional process imposes two minimal requirements on material parameters for shell growth to be obtainable within a specific synthetic system.     

Experimental studies of the bond response of three-wire strands and some influencing parameters

The bond behavior of prestressing strands is of great importance for the capacity of precast prestressed concrete structures. In the present study, the bond behavior of three-wire strands, and some influencing parameters, were examined by means of steel encased pull-through and push-in tests. The three mechanisms: adhesion, friction and other mechanical actions were found to be present at the strand-concrete interface at different slip values. The results from the experiments showed that the micro roughness of the strand surface strongly affected the initial bond response of the strand, that is the adhesion in the interface. The maximum bond capacity of indented three-wire strands was found to be directly connected to the geometric properties of the strand indents. The influence of the concrete strength on the bond capacity of the strand was hard to interpret. However, the density of the concrete matrix was found to be a better parameter for determine the influence of the concrete rather than the compressive strength.     

Magnetic-field-controlled optical transmission in a system of metal diaphragms with apertures and a thin dielectric interlayer

A system comprising two metal diaphragms with holes and a thin dielectric interlayer exhibits magnetic-field-controlled optical transmission. This phenomenon can be used, in particular, for the creation of light modulators.     

Inhibition of microbial growth in ready‐to‐eat food stored at ambient temperature by modified atmosphere packaging

This study was undertaken to develop a modified atmosphere package to control microbial growth in ready‐to‐eat (RTE) products stored at ambient temperature. Ethanol and/or limonene associated with modified atmosphere (CO₂ : O₂ : N₂ = 30% : 5% : 65%) was used to inhibit the growth of total air‐borne microorganisms and Escherichia coli in RTE products stored at 25°C. The results indicated that 0.05% ethanol vapour in the headspace was effective to inhibit the growth of air‐borne microorganisms and E. coli at 25°C for 72 h in a model study, and the effectiveness was related to ethanol content. Both 73 ppm limonene and 0.05% ethanol vapour enhanced the bacteriostatic effect of modified atmosphere in RTE sushi roll products, and no off‐flavour was detected using this formulated gas; however, no significant inhibitory effect was observed for RTE cold noodle products. This study concludes that combinations of carbon dioxide, ethanol or limonene vapours are effective to inhibit microbial growth in RTE food at ambient temperature, and the outcome may be due to the hurdle effect. Copyright © 2003 John Wiley & Sons, Ltd.     

The anisotropic effect of a weak magnetic field on the photoconductivity of C<Subscript>60</Subscript> single crystals

The effect of crystal orientation on the photogeneration of free charge carriers was studied for C₆₀ single crystals in a weak magnetic field. The photoconductivity sharply depends on the orientation of magnetic field with respect to the crystallographic directions, showing a 5–8% increase for seven axes of the C₆₀ crystal.     

Thermodynamic stability of GaInSb,InAsSb, and GaInP epitaxial films

The miscibility gaps and the critical temperatures of spinodal decomposition of ternary semiconducting Ga-In-Sb, Ga-In-P, and In-As-Sb systems are calculated by taking into account the deformation energy and the effect of plastic relaxation caused by the misfit dislocations. It is shown that taking into consideration elastic energy narrows the ranges of spinodal decomposition and lowers its critical temperature. The introduction of the phenomenological parameter into Matthews-Blakeslee formula makes it possible to reach a satisfactory agreement between theoretically calculated values of critical thickness of epitaxial films and the experimental data.     

Effects of surface charge, micro-bubble size and particle size on removal efficiency of electro-flotation.

Flotation is a water treatment alternative to sedimentation, and uses small bubbles to remove low-density particles from potable water and wastewater. The effect of zeta potential, bubble size and particle size on removal efficiency of the electro-flotation process was investigated because previous model-simulations indicated that these attributes are critical for high collision efficiency between micro-bubbles and particles. Solutions containing Al3+ as the metal ion were subjected to various conditions. The zeta potentials of bubbles and particles were similar under identical conditions, and their charges were influenced by metal ion concentration and pH. Maximum removal efficiency was 98 and 12% in the presence and absence of flocculation, respectively. Removal efficiency was higher when particle size was similar to bubble size. These results agree with modelling simulations and indicate that collision efficiency is greater when the zeta potential of one is negative and that of the other is positive and when their sizes are similar.