Solution of Helmholtz equation by Trefftz method

The application of the Trefftz method for calculating wave forces on offshore structures is presented. Indirect and direct formulations using complete and non-singular systems of Trefftz functions for the Helmholtz equation are posed in this paper. An effective technique using different interpolation functions for the velocity potential and wave force are suggested to improve the computational accuracy of the wave force. The numerical examples show that the present method is highly efficient and accurate.     

基于FLUENT软件的管式搅拌反应器流场的数值模拟

运用商业计算流体力学(CFD)软件FLUENT对一种新型管式搅拌反应器进行流场模拟,用GAMBIT建立流场实体模型,采用标准k-ε湍流模型以及多重参考系法(MRF)处理搅拌桨区.结果表明,计算所选模型能较准确地预测搅拌反应器的速度场、压力场及湍流动能分布,考察流量为1 m3/h时不同搅拌转速对反应器内部混合的影响,此时对应的最佳搅拌转速为50 rpm左右.模拟结果将为实验研究提供适当的操作参数,对搅拌反应器的优化和放大具有一定参考价值.     

Effects of compressive and tensile stress on the growth mode of epitaxial oxide films

Oxide films were deposited on different substrates by laser molecular beam epitaxy. Reflection high-energy electron diffraction was performed to in situ investigate the change of growth mode and the lattice relaxation during the growth. An asymmetrical phenomenon was found in the two kinds of strain states, compressive stress and tensile stress of heterostructures with different lattice mismatch. In the case of BaTiO₃/SrTiO₃ (2.2%), 2D layer-by-layer growth mode without lattice relaxation can be maintained for a longer period for BTO films on STO with compressive stress, comparing to STO films on BTO with tensile stress. When MgO films were deposited on SrTiO₃ with a large mismatch of 7.8%, compressive stress leads to rapid lattice relaxation with a very thin wet layer, and 3D strained island were observed. As a comparison, SrTiO₃ films on MgO with tensile stress were configured. No RHEED patterns can be observed duo to a large tensile stress.     

高柔韧性尼龙1010材料的制备

对尼龙1010/NBR/增塑剂体系进行了系统研究,发现在挤出机中环氧扩链剂可以对尼龙进行扩链反应,且环氧树脂对尼龙1010的扩链反应活性较高,扩链效果比较明显;N-丁基苯磺酰胺是尼龙的良好增塑剂,经增塑、增韧后可以使经扩链后的尼龙1010柔韧性有明显提高.采用SEM和TEM对所制备的材料进行了形貌分析,发现用NBR增韧尼龙,对于不同的基体材料,橡胶粒子的形貌有很大不同,粒子由增韧纯尼龙的椭球形变为在增塑尼龙基体中不规则的形状.     

Influence of the preparation conditions on the size and morphology of nanocrystalline lanthanum orthoferrite

Nanocrystalline LaFeO₃ is prepared by the dehydration of coprecipitated lanthanum and iron(III) hydroxides. It is shown that the behavior of the samples during heating and the size distribution of LaFeO₃ nanocrystals can be considerably different depending on the scheme used for coprecipitation of lanthanum and iron hydroxides; independently of the method employed for coprecipitation of the initial compounds, sintering of the samples at 950°C leads to the formation of lanthanum orthoferrite crystals up to 100 nm in size.     

Influence of protein and lipid concentration of the test lubricant on the wear of ultra high molecular weight polyethylene

To gain a better understanding of the ultra-high molecular weight polyethylene (UHMWPE) wear mechanism in the physiological environment, the effects of protein and lipid constituents of synovial fluid on the specific wear rate of UHMWPE were examined experimentally. The multidirectional sliding pin-on-plate wear tester was employed to simulate the simplified sliding condition of hip joint prostheses. Bovine serum γ-globulin and synthetic l--DPPC were used as model protein and lipid constituents of synovia, respectively. Results of the wear test indicated that the UHMWPE wear rate primarily depended on the protein concentration of the test lubricant. Lipids acted as a boundary lubricant and reduced polyethylene wear in the low protein lubricants. However, the polyethylene wear rate increased with increasing lipid concentrations if the protein concentration was within the physiological level. Increased interactions between protein and lipid molecules and lipid diffusion to polyethylene surface might be responsible for the increased wear.     

Synthesis of polyanilines with pendant fluorescent units

Functionalized polyanilines containing biphenyl, terphenyl, carbazole, anthracene, and 4-n-hexylphenyl moieties were synthesized though the reaction of polyaniline in emeraldine base form with sodium salt of corresponding vinylketoaromatics with quantitative yields. Polymers were characterized with Fourier transform infrared spectroscopy, proton nuclear magnetic resonance spectroscopy, and thermogravimetry. The emission characteristics of these polymers in N-methyl-2-pyrrolidone solution were examined. The functionalized polyanilines exhibited an intense green emission.     

校长要努力营造校内和谐的人际关系氛围

校长是国家教育方针的执行者,是学校行政工作的主帅,是学校活动的组织者、指挥者、协调者.如何正确处理校内人际关系,营造一个校内宽松、和谐、民主的人际环境,是校长工作中的重要环节,是能否调动校内一切积极因素、凝心聚力,形成正向合力必不可少的条件.     

Protoplast from <Emphasis Type="Italic">β</Emphasis>-carotene-producing fungus <Emphasis Type="Italic">Blakeslea trispora</Emphasis>: Preparation,regeneration and validation

The effects of key parameters on the preparation and regeneration of protoplast from the β-carotene-producing fungus Blakeslea trispora were discussed in this paper, including the combination of various enzymes, mycelial age, digesting time and temperature, pH value, osmotic stabilizers, pretreatment, culture medium and culture method. Under the condition of mixed enzymes in osmotic stabilizer (0.6 M NaCl) combined with 2% lysozyme, 3% cellulase and 3% snailase, the highest protoplast yield, as high as 7.48×106 protoplasts/mL, was obtained when mycelial age was 60 h at pH 5.0–6.0 with digesting for 14–16 h at 28 °C. After purification of the obtained protoplasts, they were regenerated in PDA regenerative medium using bilayer plate culture method. To validate the usability of the protoplasts, a novel plasmid with green fluorescent protein (GFP) was used in transformation for easy visual observation. The results showed that the protoplasts prepared by the optimized method were active and applicable in further gene manipulation experiments. This work was presented at 13 ^th YABEC symposium held at Seoul, Korea, October 20–22, 2007.