低熔点合金填充聚合物材料断口形貌研究

研究了合金元素、加工温度、金属含量、第三组分对低熔点金属填充聚合物材料断口形貌的影响。实验结果表明:不同的合金对体系的影响很大,低分子量、低结晶性聚合物,高的成型加工温度可提高材料的相容性。     

普钙产品转化率的数值计算方法

对影响普钙产品转化率的各种因素进行了分析,利用MATLAB 软件包得到了转化率的计算公式,提出了确定未分解磷矿的比例和由倍半氧化物引起的有效磷退化幅度的方法,为生产系统的预测和调整提供了一种途径。     

On the behaviour of tin-containing species in cryolite–alumina melts

Tin oxide (SnO2) dissolves in cryolite–alumina melts forming tetravalent tin species, but under reducing conditions it is reduced to divalent tin and, further, to metallic tin. Freezing point depression data for SnF2 and SnO in molten cryolite (Na3AlF6) corresponded to the formation of one and two new particles, respectively. By anodic dissolution of tin into cryolite-alumina melts divalent as well as tetravalent tin was formed, depending on current density and composition. During electrolysis of SnO2-based oxygen-evolving anodes, the condensate above the melt contained both divalent (SnF2) and tetravalent (SnO2) tin species.     

HT-730改性酚醛-丁腈胶粘剂的研制

对酚醛-丁腈胶粘剂进行改性，添加5．0％的硅烷偶联剂，改善了酚醛-丁腈胶粘剂的工艺性能，提高了粘接强度，特别是降低了酚醛-丁腈胶对环境湿度的敏感性。研制的HT-730胶在环境湿度90％时仍有很高的粘接强度，同时老化性能和适用期并没有受到影响。     

非木本木质素磺酸镁对水泥净浆和砂浆性能的影响

用红外光谱法等测定了非木本木质素磺酸镁的结构特征参数,研究了其对水泥净浆和砂浆性能的影响,并与木本木质素磺酸钙进行了对比。非木本木质素磺酸镁结构中的甲基、酚羟基、芳香环比木质素磺酸钙少;特性黏度为 0. 61mL/g,仅是木质素磺酸钙的 61%;磺化度为 0 78mmol/g,比木质素磺酸钙低约 40%。木质素磺酸镁溶液的最低表面张力为 49 82mN/m,起泡性能与木质素磺酸钙相近。非木本木质素磺酸镁对水泥净浆和砂浆减水分散作用为木本木质素磺酸钙的 86 6% ~91 1%。但掺质量分数 0 5%的木质素磺酸镁的砂浆, 28d的抗压强度比掺木质素磺酸钙的高 70 5%。     

冷冻凝聚工艺生产CR322的研制

对原电解质凝聚工艺生产CR322(混合调节型氯丁橡胶)进行了改进，实现了冷冻凝聚新工艺法生产切块CR322，即主乳化剂由松香皂／脂肪酸皂复合型代替了单一松香皂。新工艺解决了冷冻转鼓装置生产CR322过程中“黏杆”及干胶门尼黏度控制等问题。产品无焦烧粒子。且焦烧时间明显延长。     

PBT共混改性研究最新进展

综述了最近几年国内外聚对苯二甲酸丁二醇酯(PBT)共混改性的研究进展,分类介绍PBT/聚烯烃、PBT/同系聚酯、PBT/液晶、PBT/弹性体、PBT/聚碳酸酯等不同共混体系,讨论了各体系中的相行为、相容性、热稳定性、力学性能等,并对该类共混物的发展趋势作了简要的分析。     

纳米稀土复合固体超强酸催化合成乙酸苄酯

采用共沉淀法制备了纳米稀土复合固体超强酸SO4^2-／ZrO2-2％Nd2O3催化剂，电镜分析表明，催化剂颗粒直径在25nm左右，比表面积测定：71．03m^2／g。酸强度-12．70〈Ho〈-11．99。并对合成乙酸苄酯的最佳反应条件进行了研究。研究表明：当苯甲醇与乙酸的物质的量比为1：2，反应时间为5h，反应温度为120℃，催化剂用量为6％苯甲醇的质量时，酯化率可达92．04％。研究发现，该催化剂可重复使用并可活化再生。     

Preparation of micro-patterned surfaces of Si-N-O films and their influence on adhesion behavior of endothelial cells

Microgrooves were prepared on Si(100) surface by photolithography and wet etching.Subsequently,Si-N-O films were deposited on the microgrooves by unbalanced magnetron sputtering(UBMS) and micro-patterned surfaces of Si-N-O films were obtained.The size of the micropatterns was measured by surface profilometer.The chemical composition of Si-N-O films were characterized by X-ray photoelectron spectrometry(XPS) and the wettability of the micropatterned surfaces was evaluated by contact angle measurement.The beh...     

Dynamic equivalent method of interconnected power systems with consideration of motor loads

The existing equivalent methods usually only deal with static load models and neglect the dynamic characteristics of loads such as induction motors.This paper presents a dynamic equivalent method which considers motor dynamics.At first,the clustering criterion of motor loads is given.The motors with similar dynamic characteristics are classified into one group.Then,reduction of motors in the same group is carried out.Finally,parameters of the equivalent motor are calculated and the equivalent system is thus...