裂齿矩形翅片板翅式换热器优化设计的分析

对裂齿矩形翅片板翅式换热器中的裂齿矩形翅片的传热效率作了分析,并以单位质量材耗的换热能力最大为目标函数,分析研究了在不同雷诺数(Re)的操作条件下裂齿矩形翅片间角度、翅片厚、长度、宽度及极厚之间的关系。结果表明:在气体换热的场合下,当Re在某一范围时翅片可有效地起到强化传热的作用。当板厚为5mm,翅片厚为3mm,翅片间夹角为45°～70°,Re为2×10~3～8×10~3,最佳翅片纵向间距与翅片长度和翅片厚度乘积的平方根的比为1.5～2.5,最佳翅片尺寸系数为3～5时,传热强化效果较好。     

边坡支护中多种技术措施的综合应用

通过工程实例,介绍了锚杆喷射混凝土支护技术与高压喷射混凝土搅拌桩支护技术在工程中的综合利用,同时也验证了该技术的可行性及经济性。     

高压水射流射孔井眼应力数值模拟研究

水力射孔技术是一种新型完井方式,利用深穿透水力射孔技术辅助定向压裂,可实现油层改造和油井增产。考虑套管水泥环的影响,采用有限元理论结合ANSYS软件计算了高压水射流水力射孔井眼周围的应力,重点分析了水力射孔参数对井周应力的影响规律,初步研究了直井水力压裂时水力射孔对裂缝起裂的影响。计算结果表明,沿最大水平地应力方向布孔时,孔眼根部的周向拉应力最大,裂缝将会在孔眼根部起裂;选择合理水力射孔参数可有效降低地层破裂压力。研究结果可为高压水射流水力射孔辅助定向压裂提供参数优选的依据。     

负载型固体碱催化合成亚苄基丙酮

研究了用固体碱 KOH/Al_2O_3催化合成苯叉丙酮,确定了合成的最佳工艺条件:n(苯甲醛)∶n(丙酮)=1∶4.催化剂用量2g,催化剂最佳负载量12mmol/g,反应温度40～45℃,反应时间为3h,产率达88%以上。     

18臂机械井径与磁法井径组合测井仪原理及应用

文章主要介绍了18臂机械井径与磁法井径组合测井仪的仪器结构、主要技术特性、测量原理及测井资料在油田中的应用。通过对测井资料的分析，阐述了该仪器在套损检测、补贴效果检查、射孔工程作业效果评价等方面的应用，为油田套管分析提供了可靠的保证。     

Influence of halide ions and alloy microstructure on the passive and localized corrosion behavior of alloy 22

Alloy 22 (N06022) is the current candidate alloy used to fabricate the external wall of the high-level nuclear waste containers for the Yucca Mountain repository. It was of interest to study and compare the general and localized corrosion susceptibility of Alloy 22 in fluoride and chloride solutions at 90 °C. Standard electrochemical tests such as cyclic potentiodynamic polarization, amperometry, and electrochemical impedance spectroscopy were used. Studied variables included the solution pH and the alloy microstructure (thermal aging). Results show that Alloy 22 is highly resistant to general corrosion in all the solutions tested. Thermal aging is not detrimental and even seems to be slightly beneficial for general corrosion at the higher solution pHs. Pitting corrosion was never observed. Crevice corrosion was found only for high chloride-containing solutions after anodic polarization. The presence of fluoride ions together with chloride ions seems to increase the susceptibility of Alloy 22 to crevice corrosion compared to pure chloride solutions. This article is based on a presentation made in the symposium “Effect of Processing on Materials Properties for Nuclear Waste Disposition,” November 10–11, 2003, at the TMS Fall meeting in Chicago, Illinois, under the joint auspices of the TMS Corrosion and Environmental Effects and Nuclear Materials Committees.     

VC++实现的串口通讯数据处理

说明了在异步串行通信(RS-232)的工作方式下,对所接收的数据进行接收、处理,丢弃乱码,并进行保存的可靠方法,并给出了相关的VC 语言程序.     

H.264编码器软硬件设计和运动估计算法研究

介绍了基于DSP的H.264编码器实现硬件设计,对其关键部分作了功能说明,给出了基于DSP的软件设计思想,提出了多参考帧的运动估计快速算法--三维菱形搜索法(TDDS).     

Research on Marine Boiler＇s Pressurized Combustion and Heat Transfer

The effect of pressure on combustion and heat transfer is analyzed. The research is based on the basic combustion and heat transfer theorem. A correction for the heat calculation method for pressurized furnace is made on the basis of the normal pressure case. The correction takes the effect of pressurizing into account. The results show that the correction is reasonable and the method is applicable to combustion and heat transfer of the marine supercharged boiler.     

Synthesis of Mg-α-sialon from the mixture of silicon, aluminum and magnesia powders in a flowing nitrogen atmosphere

Synthesis of Mg-α-Sialon has been investigated by the mixture of silicon, aluminum and magnesia powders in a flowing nitrogen atmosphere in the range of 1300–1600 °C, when Mg-α-Sialon is designed with a chemical formulation of Mg _x Si_12−3x Al_3x O _x N_16−x in present work. The results showed that Mg-α-sialon initially occurred at 1400 °C and basically increased with elevated temperatures. For the samples of x = 0.6, 0.8 and 1.0 the products mainly consisted of Mg-α-Sialon with small amounts of Si, AlN and 21R AlN-polytypoid phases at 1600° C. However, in final products of x = 1.2, 1.4 and 1.6 only a little of Mg-α-Sialon formed and a great amount of Si remained in these samples at all the fired temperatures. Fortunately, the content of Mg-α-Sialon in these samples were obviously increased by adding a small amount of α-Si₃N₄ as seeds before nitridation.