Exothermic effect in the process of electron‐beam curing of epoxy resins

Temperature measurements have been performed in the process of electron‐beam curing of EB‐I and EB‐II epoxy resin systems. The influence of initiator content, resin type, and dose rate on the temperature of the systems was studied. Transverse and longitudinal temperatures of samples in the glass vessel were also analyzed. The nature of temperature curves varied with the different epoxy resin systems in the steel mold, but did not change with different contents of the initiator. At the same time, the heat had no effect on the gel fraction of epoxy resin systems. The temperature curve was greatly affected by the dose rate, and its peak value, peak width, and plateau value also increased with it. The transverse temperature of EB‐II glass vessel samples increased as the radiation dose increased and, in the same sample, the temperature reduced as the distance between the radiation center and the test point increased. The longitudinal temperature of EB‐I and EB‐II resin systems in a glass vessel decreased as the radiation depth increased. As the radiation dose increased, the temperature of the EB‐I resin system increased simultaneously, while that of the EB‐II resin system initially increased and then kept constant when the dose reached a certain value. The temperatures of these two resin systems decreased rapidly when the radiation process stopped. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2217–2222, 2004     

全硫化粉末丁腈橡胶改性硬质聚氯乙烯研究

研究了纳米级全硫化粉末丁腈橡胶（VP-401）对硬质聚氯乙烯（PVC-U）增韧改性材料的力学性能、流变性能及形态结构的影响。研究发现：与普通粉末橡胶P83增韧相比，采用少量的超细全硫化粉末橡胶即可在保持较高的强度和耐热温度的基础上大幅度提高硬质PVC材料的冲击韧性。     

Oxygen enrichment from air through multilayer thin low‐density polyethylene films

Several multilayer thin low‐density polyethylene (LDPE) films were fabricated by blown thin film having a thickness of 7 μm and an area of 130 cm². They were characterized for their oxygen‐enrichment performance from air by a constant pressure–variable volume method in a round permeate cell with an effective area of 73.9 cm². The relationship between oxygen‐enrichment properties, including oxygen‐enriched air (OEA) flux, oxygen concentration, permeability coefficients of OEA, oxygen, nitrogen, as well as separation factor through the multilayer LDPE films, and operating parameters, including transfilm pressure difference, retentate/permeate flux ratio, temperature, as well as layer number, are all discussed in detail. It is found that all of the preceding oxygen‐enrichment parameters increase continuously with an increase of transfilm pressure difference from 0.1 to 0.65 MPa, especially for the trilayer and tetralayer LDPE films. The oxygen concentration and separation factor appear to rapidly increase within the retentate/permeate flux ratio below 200, and then become unchangeable beyond that, whereas the OEA flux and the permeability coefficients of OEA, oxygen, and nitrogen seem to remain nearly constant within the whole retentate/permeate flux ratio investigated, especially for the monolayer and bilayer LDPE films. The selectivity becomes inferior, whereas the permeability becomes superior, as the operating temperature increases from 23 to 31°C. The highest oxygen concentration was found to be 44.8% for monolayer LDPE film in a single step with air containing oxygen of 20.9% as a feed gas and operating pressure of 0.5 MPa at a retentate/permeate flux ratio of 340 and 23°C. The results demonstrate a possibility to prepare an oxygen‐enriching membrane directly from air, based on the easily obtained thin LDPE films. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 3013–3021, 2002; DOI 10.1002/app.2331     

Mechanical and erosion properties of CaCO3‐EMAA thermal sprayed coatings

Polymer‐ceramic composite coatings manufactured from calcium carbonate and ethylene‐methacrylic acid copolymer (EMAA) were prepared via a thermal spray process employing different CaCO₃ filler sizes (average size of 2.8, 9 or 36 μm) and loading levels from about 2.5 to 7 wt%. The optimum filler feeding characteristics, deposition efficiency and deposition rate were obtained with a 36 μm sized CaCO₃. Tensile properties, peel strength, and the erosion resistance of a pure EMAA and CaCO₃‐EMAA composite coatings were investigated. It was found that the tensile strain at fracture of the composite coating decreased with the addition of filler to a greater degree than that observed in compression‐molded polymer composites. This is attributed to an inhomogenous distribution of the filler, with more being concentrated at the boundaries of the deposited polymer particles, thereby establishing a rigid framework within the coating. Only a small filler content is necessary to establish large changes in the mechanical properties of the coating. The peel strength of a composite coating decreases with filler content, both on a mild steel substrate and a previously sprayed polymer coating. Bonding to the latter is significantly higher and offers a possibility as a bonding layer between substrates and composite coatings. The coefficient of friction is lowered with the addition of a filler. Erosion testing has shown that the erosion resistance of PF111 is little improved overall with filler addition, although some increase is found for filler contents less than 5 vol%. Polym. Eng. Sci. 44:1448–1459, 2004. © 2004 Society of Plastics Engineers.     

十二烷基苯磺酸钠水溶液聚集性质的研究

用滴体积法测出十二烷基苯磺酸钠（ＳＤＢＳ）稀水溶液的表面张力；然后求出其临界胶束浓度（ＣＭＣ）。同时通过溶液的电导率、吸收光谱以及荧光光谱测定求出其ＣＭＣ。这样测出的ＣＭＣ值为１．２～１．６×１０－３ｍｏｌ／Ｌ，与文献值相符。也研究了部分水解的聚丙烯酰胺（ＰＨＰＡＭ）对ＳＤＢＳ聚集性质的影响；发现ＳＤＢＳ的ＣＭＣ值随ＰＨＰＡＭ的加人而减少并且ＰＨＰＡＭ水溶液的粘度随ＳＤＢＳ的存在而急剧降低（类似盐效应）。这些方法与性质对强化采油（ＥＯＲ）是重要的。     

粘度调节剂对制备环氧树脂微球的影响

研究粘度调节剂对环氧树脂/二氨基二苯基砜/聚醚酰亚胺(EP/DDS/PEI)共混物相结构及制备EP微球的影响。结果表明,共混物中加入粘度调节剂后,固化过程中共混体系的粘度明显降低,随着粘度调节剂用量的增加,EP分散相尺寸逐渐增大,制得的EP微球粒径及粒径分布指数逐渐增大。EP微球的红外光谱显示粘度调节剂对EP微球的成分和相结构没有明显影响。     

PP/POE/Nano-CaCO3复合材料的动态力学热分析

采用熔融共混工艺制备了聚丙烯(PP)／聚烯烃热塑性弹性体(POE)／纳米CaCO3复合材料。用动态力学试验方法研究了PP／Nano-CaCO3、PP／POE和PE／POE／Nano-CaCO3复合材料的动态力学特征。结果显示：PP／Nano-Ca-CO3PP／POE二元体系的低温内耗峰强度均比PP大；PP／POE／Nano-CaCO3三元复合体系的低温内耗峰强度较之二元体系明显增强，在PE／POE／Nano-CaCO3复合体系中，POE及Nano-CaCO3共同作用使体系tgδ1转变峰逐渐消失，tgδ2峰变宽、增强。利用扫描电子显微镜观察了不同体系的形态，三元复合体系由纯PP的耗能少的空洞化断裂方式逐步向耗能多的基体层屈服方式变化；质量比为100／10／10的PE／POE／Nano-CaCO3复合材料的低温内耗峰强度最大，冲击强度较纯PP提高了178％。     

丙碳脱碳溶剂的改进研究

介绍一种由丙碳、叔胺和少量活化剂构成的复合溶剂的开发，并详细地测定了不同压力和操作工况下，这种复合溶剂对ＣＯ２的吸收和解吸性能，以及溶剂的缓蚀性能和抗氧化性能．实验证明这种复合溶剂与纯丙碳相比，具有吸收容量大、速率快、脱碳净化度高、对设备无腐蚀等特点，对改进现行的丙碳脱碳工艺具有应用价值．     

S3C6410和CR95HF的RFID读卡系统设计

针对目前读卡器主频低、速度慢、便携性差等不足,提出了一种基于S3C6410的RFID读卡系统设计方案。本文以高性能的S3C6410嵌入式微处理器为核心,选用新型的CR95HF射频芯片,开发设计了一款高主频的搭载Android嵌入式系统的新型手持式RFID读卡器。该读卡器工作在高频13.56MHz,支持ISO14443、ISO15693等多种协议。实验证明,该读卡器能对符合协议的标签进行读写操作,读写距离能够满足需要,具有便携、稳定性高、处理速度快等特点。     

FPGA和USB的双通道数据采集测试系统

提出了一种双通道数据采集测试系统的硬件实现方案。该系统采用FPGA芯片EP1C12Q240C6,SRAM芯片CY7C1061AV33和USB芯片CY7C68013A构成硬件框架,可通过USB总线接收上位机命令并上传采集的数据到PC。本文对该系统的硬件电路和FPGA内部逻辑设计做了详细的介绍。最后经过实际测试,该系统可以有效采集ADC输出信号,验证了设计方案的正确性。