一氯胺消毒剂检测新技术及应用

讨论了传统一氯胺测定方法在应用中的局限性,并介绍了一种新的检测技术.实际应用表明该技术可以使水厂饮用水消毒中产生尽可能多的一氯胺,还可以使污水处理厂出水消毒中一氯胺的检测精确,而不受有机氯胺、亚硝酸盐和锰的干扰;帮助水厂控制过量投加氯和氨,从而降低成本.     

改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。     

Effects of compressive and tensile stress on the growth mode of epitaxial oxide films

Oxide films were deposited on different substrates by laser molecular beam epitaxy. Reflection high-energy electron diffraction was performed to in situ investigate the change of growth mode and the lattice relaxation during the growth. An asymmetrical phenomenon was found in the two kinds of strain states, compressive stress and tensile stress of heterostructures with different lattice mismatch. In the case of BaTiO₃/SrTiO₃ (2.2%), 2D layer-by-layer growth mode without lattice relaxation can be maintained for a longer period for BTO films on STO with compressive stress, comparing to STO films on BTO with tensile stress. When MgO films were deposited on SrTiO₃ with a large mismatch of 7.8%, compressive stress leads to rapid lattice relaxation with a very thin wet layer, and 3D strained island were observed. As a comparison, SrTiO₃ films on MgO with tensile stress were configured. No RHEED patterns can be observed duo to a large tensile stress.     

The stress intensity factors for a short crack partially penetrating an inclusion of arbitrary shape

Some approximate solutions for predicting the stress intensity factor of a short crack penetrating an inclusion of arbitrary shape have been developed under mode I and mode II loading conditions. The derivation of the fundamental formula is based on the transformation toughening theory. The transformation strains in the inclusion are induced by the crack-tip field and remotely applied stresses, and approximately evaluated by the Eshelby equivalent inclusion theory. As validated by detailed finite element (FE) analyses, the developed solutions have good accuracy for different inclusion shape and for a wide range of modulus ratio between inclusion and matrix material.     

渤中13-1油田井身结构优化研究

针对渤中 1 3- 1油田钻井过程中存在的主要问题 ,利用测井、地质、录井和钻井资料 ,对该油田的井身结构进行研究 ,设计出合理的井身结构 ,优化了套管程序 ,为进一步减少钻井过程中漏、喷、塌、卡等复杂情况的发生 ,提供了科学的理论依据     

Integration of prior knowledge of measurement noise in kernel density classification

Samples can be measured with different precisions and reliabilities in different experiments, or even within the same experiment. These varying levels of measurement noise may deteriorate the performance of a pattern recognition system, if not treated with care. Here we seek to investigate the benefit of incorporating prior knowledge about measurement noise into system construction. We propose a kernel density classifier which integrates such prior knowledge. Instead of using an identical kernel for each sample, we transform the prior knowledge into a distinct kernel for each sample. The integration procedure is straightforward and easy to interpret. In addition, we show how to estimate the diverse measurement noise levels in a real world dataset. Compared to the basic methods, the new kernel density classifier can give a significantly better classification performance. As expected, this improvement is more obvious for small sample size datasets and large number of features.     

Formation of the complex oxide NaNdTiO<Subscript>4</Subscript>

The processes of phase formation in the Na₂CO₃-TiO₂ and Na₂CO₃-TiO₂-Nd₂O₃ systems are investigated in the temperature range 600–900°C. The high-temperature solid-phase reactions underlying the process of formation of complex oxide NaNdTiO4 are studied. It is established that the synthesis of the NaNdTiO₄ compound occurs through the reaction of the intermediate product Na₈Ti₅O₁₄ with neodymium oxide in the temperature range 720–780°C. The optimum method is proposed for synthesizing NaNdTiO₄, which makes it possible to reduce the temperature of the synthesis, to avoid the formation of impurities, and to obtain the product in a finely dispersed state.     

书立复合冲裁模的设计

介绍了安装在液压试验机上的一种集冲裁、切口作用于一体的复合冲裁模的设计，解决了没有压力机的情况下冲裁件的加工问题。