Spreading and Curing Behaviors of a Thermosetting Droplet-Silicone on a Heated Surface

Thermosetting materials are widely used as encapsulation in the electrical packaging to protect the core electronic components from external force, moisture, dust, and other factors. However, the spreading and curing behaviors of such kind of fluid on a heated surface have been rarely explored. In this study, we experimentally and numerically investigated the spreading and curing behaviors of the silicone(OE6550 A/B, which is widely used in the light-emitting diode packaging) droplet with diameter of ～2.2 mm on a heated surface with temperature ranging from 25 ℃ to 250 ℃. For the experiments, we established a setup with high-speed camera and heating unit to capture the fast spreading process of the silicone droplet on the heated surface. For the numerical simulation, we built a viscosity model of the silicone by using the Kiuna's model and combined the viscosity model with the Volume of Fluid(VOF) model by the User Defined Function(UDF) method. The results show that the surface temperature significantly affected the spreading behaviors of the silicone droplet since it determines the temperature and viscosity distribution inside the droplet. For surface temperature varied from 25 ℃ to 250 ℃, the final contact radius changed from ～2.95 mm to ～1.78 mm and the total spreading time changed from ～511 s to ～0.15 s. By further analyzing the viscosity evolution of the droplet, we found that the decreasing of the total spreading time was caused by the decrease of the viscosity under high surface temperature at initial spreading stage, while the reduction of the final contact radius was caused by the curing of the precursor film. This study supplies a strategy to tuning the spreading and curing behavior of silicone by imposing high surface temperature, which is of great importance to the electronic packaging.     

Tuning the Operating Band of an Artificial Magnetic Conductor

Journal of Communications Technology and Electronics - Approximate formulas for calculating the coefficient of reflection from an artificial magnetic conductor (AMC) based on a capacitive lattice...     

Dissolution of Metal Oxides in a Choline Chloride–Sulphosalicylic Acid Deep Eutectic Solvent

Theoretical Foundations of Chemical Engineering - A choline chloride–sulfosalicylic acid deep eutectic solvent (DES) is proposed for dissolving the oxides Co(II), Cu(II), Zn(II), Fe(III),...     

Calculation and Experimental Determination of the Neutronics Characteristics of the IRT-T Research Reactor

Atomic Energy - The results of calculations and experimental determination of the neutronics characteristics of the IRT-T research reactor are presented. The IRT-T reactor is a pool reactor with...     

Cyclic thermal shock resistance of h-BN composite ceramics with La2O3–Al2O3–SiO2 addition

The effects of La₂O₃–Al₂O₃–SiO₂ addition on the thermal conductivity, coefficient of thermal expansion (CTE), Young's modulus and cyclic thermal shock resistance of hot-pressed h-BN composite ceramics were investigated. The samples were heated to 1000 °C and then quenched to room temperature with 1–50 cycles, and the residual flexural strength was used to evaluate cyclic thermal shock resistance. h-BN composite ceramics containing 10 vol% La₂O₃–Al₂O₃ and 20 vol% SiO₂ addition exhibited the highest flexural strength, thermal conductivity and relatively low CTE, which were beneficial to the excellent thermal shock resistance. In addition, the viscous amorphous phase of ternary La₂O₃–Al₂O₃–SiO₂ system could accommodate and relax thermal stress contributing to the high thermal shock resistance. Therefore, the residual flexural strength still maintained the value of 234.3 MPa (86.9% of initial strength) after 50 cycles of thermal shock.     

液相色谱法快速检测染色梅鱼中日落黄、柠檬黄的含量

目的建立一种快速、低成本检测染色梅鱼中日落黄、柠檬黄的方法。方法将染色梅鱼剥皮,鱼皮经70%甲醇氨水提取液提取,经EclipseXDB-C_(18)色谱柱分离,以甲醇和乙酸铵水溶液为流动相,进行梯度洗脱,流速为1.0 mL/min,柱温35℃,利用紫外检测器检测日落黄、柠檬黄的含量。结果日落黄、柠檬黄在1.25、2.5、12.5、25 mg/kg添加水平的加标回收率为80%～90%,相对标准偏差小于10%(n=6),柠檬黄检出限为0.05 mg/kg,日落黄检出限为0.025 mg/kg。结论该方法快速、准确、成本低,适合染色梅鱼中日落黄、柠檬黄的快速检测。     

Processing Metallic Bismuth to Produce Citrate

Theoretical Foundations of Chemical Engineering - Using chemical and XRD phase analysis, along with electron microscopy, the hydrolytic processing of metallic bismuth into high-purity citrate has...     

High-rate capability of carbon-coated micron-sized hexagonal TT-Nb2O5 composites for lithium-ion battery

With excellent specific capacity, superior cycle stability, safety and strong practical, Nb₂O₅ has been considered as one of the prospective anode materials for lithium-ion batteries (LIBs). However, current study suggests that Nb₂O₅ electrode materials for LIBs still face the vital issues of low electrical conductivity and poor rate performance. Therefore, carbon-coated TT-Nb₂O₅ materials are designed and synthesized through solid state method in this work, which present high specific capacity (228 mA h g^?1 at 0.2C), satisfactory rate properties (107 mA h g^?1 at 20 C). The outstanding electrochemical property can not only give the credit to the pseudocapacitance effect of TT-Nb₂O₅, but also attribute to introduction of carbon. The homogeneous carbon-coated materials enhance the electrical conductivity, increase the electron transmission speed and alleviate particle crushing. This research not only offers a new method for preparing excellent electrode materials, but also provides a kind of excellent anode material with prospective application for LIBs.