Application of a Two-Dimensional Computer Simulation to Cake Growth in Slip Casting with Complicated-Shape Gypsum Molds

A two-dimensional computer simulation method, developed by the authors using the method of finite differences, was applied to estimate the cake growth in slip casting of alumina with a triangular gypsum mold and a box-type gypsum mold with a convex bottom. The cake growth patterns, water penetration patterns, water flow rate distributions, and pressure distributions were simulated in the molds and/or cakes. The simulated cake growth patterns were in good agreement with those observed experimentally in both molds. Moreover, the cake growths could be well understood from the results of the water flow rate distributions in each case. The present method is applicable to cake growth simulation in slip casting with complicated-shape gypsum molds.     

Giant electric double-layer capacitance of heavily boron-doped diamond electrode

The physical and electrochemical properties of boron-doped polycrystalline diamond electrodes, prepared with various B/C ratio, i.e., 0.1%, 0.5% (BDD-A), 1% (BDD-B), and 5% (BDD-C), were investigated. Electrochemical measurements of the heavily boron-doped films (BDD-C) showed giant electric double-layer capacitance and activity which is significantly larger than BDD-A and BDD-B as well as glassy carbon electrodes. However, interestingly, actual boron concentration of BDD-C was observed to be almost the same as that of BDD-B by secondary ion mass spectroscopy (SIMS) and glow discharge optical emission spectroscopy (GDOES) analysis. It is suggested that the large capacitance is due to a few sp²-bonded carbon impurities, which was observed only in BDD-C, although the amount of the sp²-bonded nondiamond species are very small. In the present work, the reason for the interesting electrochemical properties of heavily boron-doped diamond electrodes is discussed. Furthermore, dimensional stability of the electrodes was also confirmed by conducting harsh anodic treatment.     

Measurement of High-Temperature Elastic Properties of Ceramics Using a Laser Ultrasonic Method

Young's modulus and Poisson's ratio of SiC ceramics at temperatures >1400°C were obtained using a laser ultrasonics method that included a Fabry-Pérot interferometer (LUFP). At temperatures <1000°C, Young's modulus and Poisson's ratio measured using the LUFP method agreed well with those measured using standard contact methods, such as the resonance method and the ultrasonic pulse method. These results showed that the LUFP method is a powerful tool for measuring high-temperature elastic properties of advanced ceramics in a noncontact manner.     

Nonequilibrium Carrier Dynamics Studied in Underdoped Bi2212 by Polarized Optical Pump-Probe Spectroscopy

We investigate nonequilibrium quasiparticle dynamics measured by ultrafast optical spectroscopy on underdoped Bi2212 crystals, which provide direct evidence that superconducting (SC) and pseudogap (PG) quasiparticles coexist below T _c . We verify that the ratio of signals from SC and PG quasiparticles depends on both excitation energy and polarization of the probe beam due to the anisotropy of the probe transition matrix elements and the interband transition probability. Based on this property, we successfully separate the SC or PG component and precisely evaluate the temperature dependence of them across T _c .     

Hydrothermal Corrosion of Alumina Ceramics

The corrosion behavior and strength degradation of alumina ceramics with 99%, 99.9%, and 99.99% Al₂O₃ were studied in water at 300°C and 8.6 MPa for 1 to 10 d. The weight loss in alumina ceramics was mainly attributed to the dissolution of SiO₂ and Na₂O grain-boundary impurities. Intergranular corrosion proceeded in the alumina ceramics by preferential attack at the grain boundaries. The extent of the strength reduction for corroded alumina ceramics was related to the impurity level in the alumina ceramics.     

Sonochemical Preparation and Properties of Pt–3Y-TZP Nano-Composites

A uniformly aggregated 3 mol% yttria-stabilized tetragonal zirconia nano-powder (3Y-TZP) was prepared using thermal hydrolysis and the ultrasonic deagglomeration technique. The possibility of nano-engineering of Pt–3Y-TZP composite aggregates was studied. The as-synthesized Pt nano-particles (∼2 nm) were impregnated into zirconia nano-aggregates (20–45 nm). The morphology manipulation technique allowed production of the composite zirconia-based aggregates in which a significant fraction of the Pt particles was embedded into the densified zirconia aggregates. Using the colloidal technique and low-temperature (1150°C) sintering, we prepared the Pt-zirconia (0.5–1.5 wt% of platinum) nano-composites with average 3Y-TZP grain sizes of 120 nm, and with the platinum grains size in the range of 20–60 nm. The catalytic properties of composite Pt–3Y-TZP nano-composites were studied and described.     

Electrical Properties of 1.7-MeV-Electron-Irradiated Sulfur-Doped GaP

The electrical properties of 1.7-MeV-electron-irradiated sulfur (S)-doped GaP were studied by using Hall effect and resistivity measurements. It was found that the concentration of S donors decreased and the deep acceptors were introduced by 1.7-MeV electron irradiation. The decrease of the concentration of S donors could be understood by considering the formation of a complex center of radiation-produced defects with S. A complex center acted as a deep acceptor and recovered in the stage centered at 150°C anneal. The introduction rate of this center was ~2.1 cm-1. From the isothermal annealing experiments, it was found that the recovery for this center approximately obeyed first-order kinetics and its activation energy was ~1.7 eV. Furthermore, another complex center involving S, which was a non-compensating defect in n-type GaP, was introduced. This center was seemed to be a deep donor.     

Impact of Key Circuit Parameters on Signal-to-Noise Ratio Characteristics for the Radio Frequency Single-Electron Transistors

Hybrid simulation was performed to analyze the response of the real-time reflection-type radio frequency single-electron transistor (RF-SET) measurement system. A compact and physically-based analytical SET model, which was validated with a Monte Carlo simulator, was used to simulate the SET characteristics, while SPICE equivalent circuits were implemented to simulate all other components of the RF-SET measurement system. The impact of various key parameters on the RF-SET response was demonstrated for a carrier frequency much less than I/e ( is the typical current through the SET). It was revealed that an inevitable feed-through loss between the tank circuit and the cryogenic amplifier, and high-frequency parasitics of the inductor degrade the RF-SET performance significantly. As such, they have to be optimized to experimentally realize the shot-noise-limited charge sensitivity.     

Signal control by successive updating of control parameters based on prediction of traffic flow

In traditional coordinated traffic signal control on an urban road network, the following two problems occur. First, the conventional method involves a time lag between traffic measurement and signal control. Second, an abrupt switching of control parameters throws the traffic flow into disorder. This paper proposes a new approach to avoid these problems. We increase the frequency of switching. The control parameters are switched as frequently as every two cycles. At the time of switching, minor variations of the ongoing plan are generated. For each variation of plan, traffic delay at each intersection is predicted based on measured traffic data at upstream detectors. Then the plan minimizing the delay is chosen to be the control parameters in the next cycle. In order to evaluate the validity of this approach, experiments were carried out using a traffic simulator. The experiments indicate that the proposed method reduces the queue length significantly, compared with the conventional method. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 161(3): 49–57, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20391     

Incorporation of a well-defined polyether side-chain into segmented poly(ether-urethane urea) and examination for blood-compatibility

A new method of introducing a hydrophilic polyether side chain into segmented polyurethane using a polypropylene oxide macromer with 1,3-diol at one chain-end, which behaves as chain extender, is described. In this procedure, a molecular-designed side-chain is incorporated quantitatively and directly into polyurethane biomedical elastomer. The design is also of interest to biomaterials in artificial organs.