Characteristics of membrane humidifiers for polymer electrolyte membrane fuel cells

Water management plays an important role in obtaining high performance from a polymer electrolyte membrane fuel cell (PEMFC). To reduce the volume and energy consumption of widely-used bubble humidifiers, membrane humidifiers were fabricated by using an ultrafiltration (UF) membrane and Nafion membranes. The performance of the membrane humidifiers was examined as a function of gas flow rate and operating temperature. A single cell was operated using the UF membrane humidifiers exhibiting almost the same performance with that employing bubble humidifiers.     

The permeation resistance of interface and the directional dependence of permeation in plasma-grafted composite membranes

Composite membranes were prepared by grafting plasma-polymerized films onto the surface of nonporous poly (dimethylsiloxane) films. Gas permeabilities of the composite membranes were measured at 35°C, 1 atm for N₂, 0₂, CO₂ and CH₄. The permeation properties of the composite membrane was analyzed using the series resistance model. There was a great interfacial resistance to CH₄ permeation through the composite membrane. The interfacial resistance was negligible for the other gases. The interfacial resistance seems to be a result of an interfacial layer caused by the interaction between the bulk two layers. For CH₄ gas, the permeation rate through the composite membrane was affected by the direction of flow. The directional dependence was negligible for the other gases.     

Preparation and characterization of polypropylene/layered silicate nanocomposites using an antioxidant

Polypropylene (PP)/layered silicate nanocomposites were prepared via simple melt mixing of three components, PP, layered silicates modified with octadecylamine (C18-MMT) and antioxidant, to investigate the role of antioxidant. TEM and X-ray scattering results confirmed the intercalated state of silicates in PP/layered silicate nanocomposites with antioxidant. In rheological and mechanical study, the nanocomposites with antioxidant showed higher properties than those of the unfilled PP. The nanocomposite with 5 wt% C18-MMT and 0.5 phr antioxidant exhibited about 1.4 times higher tensile modulus and 1.3 times higher storage modulus than the unfilled PP. However, PP/C18-MMT without antioxidant showed lower rheological values owing to the thermal decomposition of PP and the poor compatibility between PP and C18-MMT. It could be concluded that antioxidants played an important role in enhancing the compatibility between PP and C18-MMT. According to the real time X-ray diffraction, the nanocomposite showed the weak ordering of PP crystals than the unfilled PP in the load-extension plateau region of elongation.     

Effect of reactive diluents on properties of unsaturated polyester/montmorillonite nanocomposites

Unsaturated polyester (UP)/montmorillonite (MMT) nanocomposite was prepared by using hydroxypropylacrylate (HPA) as a reactive diluent instead of conventional styrene monomer and the effect of polarity of reactive diluent on properties of nanocomposite was investigated. X‐ray and mechanical test data indicated that mixing for an extended period of time is essential to enhance the physical properties of nanocomposites in the UP/Cloisite 6A system. This was attributed to the high polarity of HPA that may disturb the preintercalation of UP resin into the galleries of MMT. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 238–242, 2004     

Dynamic mechanical properties of three different combinations taken from styrene-co-itaconate, styrene-co-methacrylate, and styrene-co-sulfonate ionomers

Dynamic mechanical properties of three different styrene-based ionomer blends containing ca. 5 mol% of ionic repeat units were investigated; the three ionic units were itaconate (ITANa), methacrylate (MANa), and styrenesulfonate (SNa). For SNa-MANa ionomers, it was observed that this ionomer system showed only two loss tangent peaks, implying that this ionomer system resembles a typical miscible system. When the ion content increased, however, the ionomer blend showed two cluster loss tangent peaks, indicating the presence of phase-separated cluster regions. This suggests that, with increasing ion content, the role of ionic units becomes more important than that of host non-ionic units to determine ionomer properties. In the case of ITANa-MANa and ITANa-SNa ionomers, however, it was suggested that the multiplets of the MANa and SNa ionomers might be disrupted upon the addition of the ITANa ionomers. In addition, the SEM images showed that the fracture surfaces of ionomers changed upon blending.     

Monodisperse polymer/metal composite particles by electroless chemical deposition: Effect of surface functionality of polymer particles

Micron‐sized polymer particles were coated with layers of nickel compounds by plating electrolessly in the presence of aqueous solutions of nickel chloride, sodium hypophosphite, sodium citrate, and ammonium chloride at elevated temperature. The uniform functional polymer particle could be obtained by seeded polymerization. To investigate the effect of surface functionality on the conditions for nickel deposition, the polymer particle was functionalized with the thiol group. From morphological observation, it was found that the mode of nickel deposition was greatly dependent on the surface functionality of the polymer particle. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 420–424, 2003     

An analysis of muscles from ultrasound image using morphological information of fascia and thoracic vertebra

In this paper, we propose a new fully computerized image analysis method for measuring the thickness of muscles from ultrasound image obtained by muscle endurance test using morphological information of fascia and thoracic vertebra. Firstly, we divide the image into lumbar region and thoracolumbar region by the difference of density in image for measuring the thickness of muscles. In lumbar region, we notice that the intensity of fascia is relatively higher than other parts. Thus, we measure the thickness of muscles surrounding the fascia area. In the process, we apply median filter to candidate fascia areas for extracting candidate muscle layers between fascias. Then, the thickness of muscles we measure is that of the third layer. In thoracolumbar region, we apply region expansion method for classifying the region into subcutaneous fat part and part including thoracic vertebra. Then, we apply counting method and evolutionary computation search model to find the measuring location that is in between subcutaneous fat area and thoracic vertebra. In experiment, the proposed method is effective in measuring the thickness of muscles and avoids failures of previous studies. The performance of this approach is sufficiently comparable to that of medical experts.     

Preparation of nano-sized silicon carbide powder using thermal plasma

Nano-sized silicon carbide (SiC) powder was prepared by thermal plasma process using silicon tetrachloride (SiCl₄) and methane (CH₄). The synthesized powder was characterized by X-ray diffraction pattern, scanning electron microscopy, transmission electron microscopy, FT-IR spectroscopy and particle size analyzer. The powder was dominated by β-SiC including some of α-SiC and free carbon species. The quality of the powder was varied with process conditions such as the molar ratio of H/Si and C/Si, and collecting positions. It was known that the conversion to SiC was mainly affected by the addition of hydrogen gas because it promoted the decomposition and reduction of SiCL. CH₄ was easily decomposed to carbon species for the formation of SiC as well as removal of impure oxygen, but excessive carbon suppressed the formation of crystalline SiC and resulted in the solid carbon contamination. The optimum ratio of H/Si was approx. 26 and that of C/Si was 1.1. For collecting positions, the powder collected at the vessel and filter was preferable to that at the reaction tube. The average size of the powder synthesized was estimated to be below 100 nm and uniform in distribution.     

Thermal and mechanical properties of the polymers synthesized by the sequential polymerization of propylene and 1‐hexadecene

The block copolymer of poly(1‐hexadecene) (PHD) and polypropylene (PP) was effectively synthesized by the sequential polymerization of propylene and 1‐hexadecene by using highly isospecific TiCl₃/Cp₂Ti(CH₃)₂ (Cp = cyclopentadienyl). The block copolymers had two separate melting temperatures of constituent blocks. The modulus of PHD–PP block copolymer was enhanced as the content of sequentially polymerized PP block was increased. The elongation at break showed positive deviation at the intermediate compositions from the simple additive values of constituent homopolymers. Shape memory effect which utilizes the crystalline PHD block as a reversible phase and the crystalline PP block as a fixed structure was examined. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1709–1715, 2002; DOI 10.1002/app.10551     

Molecular species of 1-O-alk-1′-enyl-2-acyl-, 1-O-alkyl-2-acyl- and 1,2-diacyl glycerophospholipids in Japanese oysterCrassostrea gigas (Thunberg)

Molecular species of 1-O-alk-1′-enyl-2-acyl-, 1-O-alkyl-2-acyl-, and 1,2-diacyl-sn-glycero-3-phosphoethanolamine (EPL) andsn-glycero-3-phosphocholine (CPL) of Japanese oysterCrassostrea gigas were analyzed by selectedion monitoring gas chromatography/mass spectrometry using electron impact ionization. The characteristic fragment ions, [RCH=CH+56]⁺ due to the alkenyl residue in thesn-1 position and [RCO+74]⁺ due to the acyl residue in thesn-2 position of alkenylacylglycerols, [R+130]⁺ due to the alkyl residue in thesn-1 position and [RCO+74]⁺ due to the acyl residue in thesn-2 position of alkylacylglycerols, [RCO+74]⁺ due to the acyl residues in thesn-1 and/orsn-2 positions of diacylglycerols, and [M−57]⁺ being indicative of the corresponding molecular weight, were used for structural assignments. For alkenylacyl EPL and CPL, 19 and 16 molecular species were determined, respectively. Two molecular species, 18∶0alkenyl-22∶6n−3 and 18∶0-alkenyl-22∶2-non-methylene interrupted diene (NMID), amounted to 53.2% and 47.9%, respectively. The alkylacyl EPL and CPL consisted of 16 and 20 molecular species, respectively, and the prominent components were 18∶0alkyl-22∶2NMID, 20∶1alkyl-20∶1n−11 (27.4%) and 20∶1alkyl-20∶2NMID (16.3%) in the former, and 16∶0alkyl-20∶5n−3 (23.0%) and 16∶0alkyl-22∶6n−3 (21.6%) in the latter. For the diacyl EPL and CPL, 14 and 51 molecular species were determined, respectively. The major molecular species were 18∶0–20∶5n−3 (37.4%), 16∶0–20∶5n−3 (14.2%) and 18∶1n−7–22∶2NMID (13.2%) in the former, and 16∶0–20∶5n−3 (33.4%) and 16∶0–22∶6n−3 (22.3%) in the latter. It was found that there were significant differences in the molecular species between the alkylacyl and diacyl EPL and the alkylacyl and diacyl CPL; the number of molecular species was larger in CPL than in EPL, while the number of total carbons and double bonds of the major molecular species were larger in the EPL than in the CPL. Alkenylacyl EPL were similar to alkenylacyl CPL in molecular species composition.