La doping effects on intergrowth Bi2WO6–Bi3TiNbO9 ferroelectrics

La doping effects on intergrowth Bi₂WO₆–Bi₃TiNbO₉ ferroelectric ceramics were studied by X-ray diffraction, electron probe microanalysis and dielectric spectroscopy. It was found that the La³⁺ distribution, ferroelectric phase transition and dielectric relaxation behavior are apparently affected by La doping. With increasing La³⁺ content, the site of dopant ion varies, the grain growth of Bi₅TiNbWO₁₅ is restrained, the Curie temperature is reduced and broadened. Furthermore, two dielectric relaxation loss peaks were observed both in temperature and frequency spectra. The calculated relaxation parameters revealed the oxygen vacancy related to the relaxation process.     

氧化铝厂渣浆泵机械密封的失效形式及改进措施

本文介绍了渣浆泵机械密封的失效形式,并根据长期现场工作经验,分析了机械密封泄漏的主要原因,据此提出了改进措施,通过对动静环密封面倒角,改变密封面尺寸及载荷系数后有效地解决了由于径向跳动过大而引起的密封面刮碰擦裂的失效问题。     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

Data mining of resilience indicators

In recent years, the Asia-Pacific region has experienced several financial setbacks, including speculative attacks in 1998 and the SARS outbreak in 2003. Financial stresses of this nature are unanticipated, and not all of the dangers can be predicted by the examination of market information and macroeconomic indicators. The Early Warning System (EWS) that has been adopted by the International Monetary Fund may not be able to predict future financial crises for all possible scenarios, because shocks come in many different forms. To supplement the EWS, this paper proposes a data mining framework to measure the resilience of an economy. The resilience framework does not predict a crisis, but rather assesses the current state of health of an economy and its ability to withstand a financial shock should one occur. The framework is based on a feedback system consisting of two stages. The first stage assigns a resilience score to each economy based on a fuzzy logic scoring scheme that is built on the ambiguous reasoning of experts. The second stage uses the classification tree approach to estimate thresholds for each economic indicator, and examines the quality of the fuzzy score. The result from the second stage is then passed back to the first stage as feedback. The final result is obtained when the feedback system reaches its equilibrium state. The proposed resilience framework is applied to the external-sector and the public-sector economies of several countries to illustrate its applicability.     

Single-Threaded vs. Multithreaded: Where Should We Focus?

Today, with the increasing popularity of multicore processors, one approach to optimizing the processor's performance is to reduce the execution times of individual applications running on each core by designing and implementing more powerful cores. Another approach, which is the polar opposite of the first, optimizes the processor's performance by running a larger number of applications on a correspondingly larger number of cores, albeit simpler ones. The difference between these two approaches is that the former focuses on reducing the latency of individual applications or threads (it optimizes the processor's single-threaded performance), whereas the latter focuses on reducing the latency of the applications' threads taken as a group (it optimizes the processor's multithreaded performance). The panel, from the 2007 Workshop on Computer Architecture Research Directions, discusses the relevant issues.     

钛白粉副产物硫酸亚铁生产硫酸铵和氧化铁红的研究

以硫酸法钛白粉副产物绿矾为原料 ,生产硫酸铵和铁红粉 .用含臭氧 ( 5 0 0mg/h)的空气在5 0℃将FeCO3氧化成Fe2 O3·nH2 O .通过煅烧制铁红产品 ,其质量达HO0 1 - 0 2 一级品要求 ;硫酸铵通过净化、除杂、浓缩、结晶 ,生产一级品硫铵 .实验证明 ,本工艺氧化时间短 ,产品质量稳定     

The flame retardant mechanism of polyolefins modified with chalk and silicone elastomer

This paper presents the current understanding of the flame retardant mechanism of Casico?. The study includes the flame retardant effect of each individual component: ethylene–acrylate copolymer, chalk and silicone elastomer, as well as the formation of an intumescent structure during heating. The flame retardant properties were investigated by cone calorimetry and oxygen index tests. To obtain insight into the flame retardant mechanism, heat treatment under different conditions has also been performed. The results indicate that the flame retardant mechanism of Casico is complex and is related to a number of reactions, e.g. ester pyrolysis of acrylate groups, formation of carbon dioxide by reaction between carboxylic acid and chalk, ionomer formation and formation of an intumescent structure stabilized by a protecting char. Special emphasis is given to the formation of the intumescent structure and its molecular structure as evaluated from ¹³C MAS‐NMR and ²⁹Si MAS‐NMR, ESCA and XRD analysis. After treatment at 500°C the intumescent structure consists mainly of silicon oxides and calcium carbonate and after treatment at 1000°C the intumescent structure consists of calcium silicate, calcium oxide and calcium hydroxide. Copyright © 2003 John Wiley & Sons, Ltd.     

Associative properties of perfluorooctyl end‐functionalized polystyrene–poly(ethylene oxide) diblock copolymers

The synthesis of 2,2,3,3‐tetrahydro‐perfluoroundecanoyl end‐functionalized polystyrene–poly(ethylene oxide) block (PS‐block‐PEO‐R_F) copolymers and their matching PS‐block‐PEO diblock copolymers was carried out by sequential anionic polymerization. Viscometry and ¹⁹F NMR studies show that the PS‐block‐PEO copolymers, in contrast to their matching PS‐block‐PEO‐R_F copolymers, exhibit a micellar rather than the associative behavior seen for the latter. However, the presence of an excess of fluorinated acid, used for end‐functionalization, produces a reduction of the associative behavior above the overlap concentration, with the fluorinated acid acting like a surfactant. A competition may also occur between PS—and R_F—mediated micellization. Copyright © 2004 Society of Chemical Industry     

Methacryloxyethyl phosphate‐grafted expanded polytetrafluoroethylene membranes for biomedical applications

Expanded polytetrafluoroethylene (ePTFE) membranes were modified by graft copolymerization with methacryloxyethyl phosphate (MOEP) in methanol and 2‐butanone (methyl ethyl ketone (MEK)) at ambient temperature using gamma irradiation. The effect of dose rate (0.46 and 4.6 kGy h^?1), monomer concentration (1–40 %) and solvent were studied and the modified membranes were characterized by weight increase, X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). XPS was used to determine the % degree of surface coverage using the C? F (ePTFE membrane) and the C? C (MOEP graft copolymer) peaks. Grafting yield, as well as surface coverage, were found to increase with increasing monomer concentration and were significantly higher for samples grafted in MEK than in methanol solution. SEM images showed distinctly different surface morphologies for the membranes grafted in methanol (smooth) and MEK (globular), hence indicating phase separation of the homopolymer in MEK. We propose that in our system, the non‐solvent properties of MEK for the homopolymer play a more important role than solvent chain transfer reactions in determining grafting outcomes. Copyright © 2005 Society of Chemical Industry