中药桂枝总黄酮的提取工艺研究

优化桂枝总黄酮的提取工艺，建立桂枝的提取和含量测定方法。通过单因素试验，考察提取方法、提取溶剂浓度、提取体积、提取时间对药材总黄酮含量的影响，采用正交试验，优化提取工艺条件，筛选出桂枝总黄酮的最佳提取工艺。总黄酮最佳提取工艺为75%乙醇、料液比1:40、回流提取时间60 min。该方法能有效测定桂枝药材总黄酮的含量，为该药材的质量标准研究提供一定的科学依据。本方法重复性较好、方法稳定、可行。     

Reducing web latency with coding-based fast multi-path loss recovery

Wireless Networks - TCP latency is critical to the performance of Web services. However, packet loss greatly impairs the TCP performance due to its poor loss recovery mechanisms. Recent work FUSO...     

One step method of structure engineering porous graphitic carbon nitride for efficient visible-light photocatalytic reduction of Cr(Ⅵ)

Porous g-C3N4 nanosheets (PCN) were prepared by the nickel-assisted one-step thermal polymerization method.Hydrogen (H2) which was produced by the reaction between nickel (Ni) foam and ammonia (NH3) defined the structure and properties of PCN.During the formation of PCN,the participation of H2 not only enhanced the spacing between layers but also boosted the specific surface area that more active sites were exposed.Additionally,H2 promoted pores formation in the nanosheets,which was beneficial to the transfer of photons through lamellar structure and improved the absorption efficiency of visible light.Remarkably,the obtained PCN possessed better Cr(Ⅵ) photocatalytic reduction efficiency than pure g-C3N4.The reaction rate constant (k) of PCN (0.013 min-1) was approximately twice that of bare g-C3N4 (0.007 min-1).Furthermore,the effects of original pH and concentration of Cr(Ⅵ)-containing solution on removal efficiency of Cr(Ⅵ) were explored.A possible photocatalytic mechanism was proposed based on the experiments of radical scavengers and photoelectrochemical characterizations.     

Toughness and R-curve behaviour of laminated Si3N4/SiCw ceramics

Laminated Si₃N₄/SiC_w ceramics were successfully prepared by tape casting and hot-pressing. Its mechanical properties were measured and the impact resistance was discussed. The toughness of the laminated Si₃N₄/SiC_w ceramics was 13.5 MPa m^1/2, which was almost 1.6 times that of Si₃N₄/SiC_w composite ceramics, namely 8.5 MPa m^1/2. Moreover, the indentation strength of laminated Si₃N₄/SiC_w ceramics was not sensitive to increasing indentation loads and exhibited a rising R-curve behaviour, indicating that the laminated Si₃N₄/SiC_w ceramics had excellent impact resistance. The improved toughness and impact resistance of laminated Si₃N₄/SiC_w ceramics was attributed to the residual stress caused by a thermal expansion coefficient mismatch between the different layers, resulting in crack deflection and bridging of SiC whiskers in the interface layer, thus consuming a large amount of fracture work.     

Synthesis of nanopowders with low agglomeration by elaborating Φ values for producing Gd2O3-MgO nanocomposites with extremely fine grain sizes and high mid-infrared transparency

Refining ceramic microstructures to the nanometric range to minimize light scattering provides an interesting methodology for developing novel optical ceramic materials. In this work, we reported the fabrication and properties of a new nanocomposite optical ceramic of Gd₂O₃-MgO. The citric acid sol-gel combustion method was adopted to fabricate Gd₂O₃-MgO nanocomposites with fine-grain sizes, dense microstructures and homogeneous phase domains. Nanopowders with low agglomeration and improved sinterability can be obtained by elaborating Φ values. Further refining of the microstructure of the nanocomposites was achieved by elaborating the hot-pressing conditions. The sample sintered at 65 MPa and 1300 °C showed a quite high hardness value of 14.3 ± 0.2 GPa, a high transmittance of 80.3 %–84.7 % over the 3?6 μm wavelength range, due mainly to its extremely fine-grain size of Gd₂O₃ and MgO (93 and 78 nm, respectively) and high density.     

Auto-registration of medium and high spatial resolution satellite images by integrating improved SIFT and spatial consistency constraints

Feature-based methods have been developed in the past decades for the registration of optical satellite images. However, it is still a challenging problem to handle well the registration between medium and high spatial resolution images due to the large difference of the spatial structural features and local details for the same objects. In this study, an automated co-registration technique is proposed that integrates an improved SIFT (I-SIFT) and a novel matching strategy called spatial consistency constraints (SCC) to cope with the large difference in spatial resolutions between the image pair. Three constraints on angle, distance, and ratio are introduced to re the initial matching features obtained by I-SIFT. Three groups of experiments were conducted to validate the effectiveness of the proposed method. The experiments used high resolution multispectral and panoramic SPOT 5/6 images and Landsat 5/8 orthorectification images. Experimental results show that the registration error lies in about 1 pixel of high-resolution images and demonstrate that the proposed I-SIFT-SCC approach is suitable for fine registration of optical satellite images from medium spatial resolution to high spatial resolution with resolution ratio up to 6.     

An index structure supporting rule activation in pervasive applications

World Wide Web - Rule mechanism has been widely used in many areas, such as databases, artificial intelligent and pervasive computing. In a rule mechanism, rule activation decides which rules are...     

喷油方式对斜齿轮齿面温度的影响

为探讨喷油方式对齿面温度的影响，以斜齿轮为研究对象，通过CFD仿真和试验研究不同喷油方式对斜齿轮齿面温度的影响。针对斜齿轮喷油润滑过程的特点，分析其齿面摩擦生热量，简化轮齿喷油润滑计算模型，并基于CFX进行齿面对流换热仿真研究，得到了不同喷油方式下的齿面温度；基于功率开放式斜齿轮试验平台，对不同喷油方式下的齿面温度进行了试验测量，与仿真计算结果进行对比分析。结果表明：在高速重载斜齿轮传动系统中，啮出侧喷油润滑的方式比啮入侧喷油润滑方式的冷却降温效果要好。