Effective sludge solubilization treatment by simultaneous use of ultrasonic and electrochemical processes.

Sludge disintegration treatment by using simultaneously ultrasonic irradiation and electrolysis was investigated experimentally. A lab-scale diaphragm cell irradiated with ultrasound at a constant oscillating frequency of 20 kHz was used as a reactor. The batch experiments were carried out under different conditions of electric outputs of the ultrasonic generator, electric current for the electrolysis and different initial SS concentrations. A simultaneous treatment in the cathodic compartment without any chemical doses considerably facilitated the sludge solubilization, compared to the sonication alone. An increase in the electric current up to 400 mA under a constant ultrasonic density decreased the specific energy by 55% within the experimental range. The specific energy consumption was also reduced when the initial SS concentration increased. In addition, before carrying out the simultaneous treatment, a brief electrolysis was effective for further reduction of the specific energy and the acceleration of soluble COD generation.     

Comparative study of the elimination of toluene vapours in twin biotrickling filters using two microorganisms Bacillus cereus S1 and S2

BACKGROUND: To investigate the microbial degradation performance of organic pollutants in the atmosphere using a biotrickling filter, two microorganism strains, Bacillus cereus S1 and Bacillus cereus S2, were selected, identified and inoculated into a twin biotrickling filter for comparison. RESULTS: Both strains showed good performance towards the degradation of model organic pollutants when gas flow rates ranged from 100 to 600 L h⁻¹. For S1, the total maximum removal efficiency (RE) of toluene was maintained nearly 100% not only at gas flow rates of 100 L h⁻¹ corresponding to empty bed residence time (EBRT) 199.44 s, but also at gas flow rates of 200 L h⁻¹ (EBRT = 99.72 s) and 300 L h⁻¹ (EBRT = 66.48 s). However, S2 had a much lower degradation capability; near 100% removal efficiency was obtained only at the gas flow rate of 100 L h⁻¹ although both bacteria belong to the same Bacillus cereus. With further increase in gas flow rate, the total REs for both S1 and S2 decreased slightly at first and then dropped sharply to 46% and 35%, respectively, at an EBRT of 33.24 s, corresponding to a gas flow rate of 600 L h⁻¹. Starvation for between 2 and 10 days resulted in the re‐acclimation times of both strains ranging between 1.0 and 15.5 h. CONCLUSION: Strain S1 would be a better choice for inoculation into a biotrickling filter than strain S2, because of its much higher toluene removal capacity and rapid recovery to full performance. Copyright © 2008 Society of Chemical Industry     

Evaluation of Soybean Seedcoat Cracking During Drying:PART II. Using MRI

MRI techniques were developed and employed for non-destructive and noninvasive study of seedcoat cracking in low moisture soybean kernels during heated air drying. Proton density image and transient moisture distribution profile of a single soybean kernel can be obtained using MRI. These MRI techniques proved to be particularly useful for the continuous observation of initiation and propagation of seedcoat cracking during the entire period of drying process without interruption.

The proton density images of soybean kernels showed that seedcoat cracking was initiated perpendicular to the long axis of the kernel near the hilum. The transient moisture distribution profiles in soybean kernels during drying indicate that moisture gradient developed during drying was higher in the seedcoat than in the cotyledon. Drying temperature and initial average moisture content were positively correlated with the soyhean seedcoat crackig. The location of the     

Nonlinear distortion prediction of active filters

The represention of circuit variables in frequency-domain complex matrix and nonlinearities by power series gives rise to a nonlinear distortion prediction technique, the intermodulation-balance method. This operates entirely in the frequency domain. The technique is verified by a single-amplifier filter with a two-tone input signal     

低负荷维氏硬度法的负荷选择

本文按照维氏硬度测定的技术条件,将基本公式H_v=1854P/D~2加以变换,从而得到一些较为简单的数学关系式.利用这些关系式,可以对不同金属薄带材料,很容易计算出较合理的负荷大小,既能保证不被"打穿",也使视场内有一个适合观测的压痕图象.     

CAD与CAPP集成研究回转体类零件特征识别

本文研究了回转体轴类,轴套类零件的特征识别。对这类零件常用的特征单元进行了定义,描述了这类零件的特征模型:介绍了它的识别方法和特征参数定义方法。     

磁性材料产业现状与展望

介绍磁性材料的主要品种，如永磁体、软磁体和磁记录介质材料的行业现状及技术进步。     

光催化剂SrTiO3的制备及其性能的研究

论述用化学液相共沉淀法制备SrTiO_3的最佳条件,及在不同的活化条件下对SrTiO_3光催化性能的影响。此外还研究了掺入过渡金属氧化物对SrTiO_3催化性能的改善。