Synthesis of Nano-Sized Platinum Metal Particles on Ti-Containing Mesoporous Silica Using Microwave-Assisted Deposition Method

Using microwave-assisted deposition method the uniform and nano-sized platinum metal particles were prepared on the tetrahedrally coordinated Ti-oxide moieties isolated within the framework of mesoporous silica supports. The present nano-sized metal catalyst exhibited a higher activity for hydrogenation of nitrobenzene than the catalyst prepared by a conventional impregnation method.     

Pt and Sn Doped Sputtered CeO2 Electrodes for Fuel Cell Applications

The interaction of Pt with CeO₂ layers was investigated by using photoelectron spectroscopy. Thirty‐nanometre‐thick Pt and Sn doped CeO₂ layers were deposited simultaneously by rf‐magnetron sputtering on a Si(001) substrate and a carbon diffusion layer of a polymer membrane fuel cell by using a composite CeO₂–Pt–Sn target. The laboratory XPS and synchrotron radiation soft X‐ray and hard X‐ray photoemission spectra showed the formation of cerium oxide with completely ionised Pt^2+,4+ species, and with Pt⁴⁺ embedded in the film bulk. Hydrogen/air fuel cell activity measurements normalised to the amount of Pt used revealed high specific power of up to 5.4 × 10⁴ mW mg^–1 (Pt). The activity of these materials is explained by the strong activity of embedded Ptⁿ⁺ cations.     

In situ observation of initial rust formation process on carbon steel under Na2SO4 and NaCl solution films with wet/dry cycles using synchrotron radiation X-rays

Atmospheric corrosion of steel proceeds under thin electrolyte film formed by rain and dew condensation followed by wet and dry cycles. It is said that rust layer formed on steel as a result of atmospheric corrosion strongly affects the corrosion behavior of steel. The effect of environmental corrosiveness on the formation process and structure of the rust layer is, however, not clear to date. In this study, in situ observation of the rusting process of a carbon steel covered with a thin film of Na₂SO₄ or NaCl solution was performed under a wet/dry repeating condition by X-ray diffraction spectroscopy with white X-rays obtained from synchrotron radiation. The present in situ experiments successfully detected initial process of the rust formation. In the early cycles, the rust constituents were not well crystallized yet, but the presence of Fe(OH)₂ and Fe(OH)₃ was confirmed. In the subsequent cycles, two different solutions resulted in difference in preferential phase of the rust constituents. α-FeOOH was preferentially formed in the case of the Na₂SO₄ solution film, whereas β-FeOOH appeared only under the NaCl solution film.     

Alternating copolymers of carbon dioxide with glycidyl ethers for novel ion-conductive polymer electrolytes

To overcome the low ionic conduction of existing poly(ethylene oxide)-based polymer electrolytes, we consider polycarbonates obtained from the copolymerization of CO₂ and epoxy monomers. We synthesized four types of polycarbonates possessing phenyl, n-butyl, t-butyl and methoxyethyl side groups using zinc glutarate, and measured the ionic conductivity of their electrolytes, including 10 mol% of LiTFSI. The electrolyte possessing methoxyethyl side groups had the highest conductivity, of the order of 10⁻⁶ S cm⁻¹ at room temperature. The activation energy (E_a) for ionic conduction in the polycarbonate electrolytes was estimated from the VTF equation, and the E_a of the electrolyte possessing n-butyl side groups was almost the same with the polyether-based electrolytes. An interesting feature of our study is that the polycarbonate is a unique candidate for ion-conductive polymers because of its flexible and hydrophobic properties.     

Design,Synthesis, and Biological Evaluation of Lysine Demethylase 5 C Degraders

Lysine demethylase 5 C (KDM5C) controls epigenetic gene expression and is attracting great interest in the field of chemical epigenetics. KDM5C has emerged as a therapeutic target for anti-prostate cancer agents, and recently we identified triazole 1 as an inhibitor of KDM5C. Compound 1 exhibited highly potent KDM5C-inhibitory activity in in vitro enzyme assays, but did not show strong anticancer effects. Therefore, a different approach is needed for the development of anticancer agents targeting KDM5C. Here, we attempted to identify KDM5C degraders by focusing on a protein-knockdown strategy. Compound 3 b , which was designed based on compound 1 , degraded KDM5C and inhibited the growth of prostate cancer PC-3 cells more strongly than compound 1 . These findings suggest that KDM5C degraders are more effective as anticancer agents than compounds that only inhibit the catalytic activity of KDM5C.     

Biodegradation of poly(lactic acid)—cassava bagasse composites produced by injection molding

Neat poly (lactic acid) (PLA) and PLA/cassava bagasse (CB) composites were used to produce seedling tubes by extrusion and injection molding. The tubes were buried in simulated soil, and their biodegradation was investigated by weight loss, scanning electron microscopy (SEM), and Fourier transform infrared spectroscopy (FTIR). After 180 days, the composites' biodegradation was higher than neat PLA material, and the higher the CB content, the higher the biodegradation, which caused fissures and voids in the material. The biodegradation of PLA/CB composites increased the phosphorus content in the soil after 180 days. Composites of PLA with CB, an abundant agro-industrial residue in Brazil, are promising because they can reduce the environmental impact due to CB's proper destination, and the composites' costs and biodegradation are faster than pure PLA material. Both the faster biodegradation of the tube and the higher P content are advantageous for seedling tubes.     

pH sensitive phosphate crosslinked films of starch-carboxymethyl cellulose

This work aims to develop hydrogel films of starch and carboxymethyl cellulose (CMC) crosslinked with sodium trimetaphosphate (STMP) and to characterize some of their properties. Starch and STMP (S/T), starch and CMC (S/C), and mixed (S/T/C) films were prepared by casting. The degree of substitution, morphology, swelling degree, FTIR, mechanical properties, and sorption isotherms were studied. Reticulated samples (S/T and S/T/C) showed the same degree of substitution (0.050 ± 0.001). All films presented homogeneous morphology, but the mixed film showed greater roughness. Crosslinking increased the swelling capacity of the mixed hydrogel at pH 7, although it remained decreased concerning the S/T hydrogel. However, this property was sensitive to pH variations. The mixed film (S/T/C) showed greater mechanical resistance. The casting process was efficient to produce hydrogel films of starch/CMC crosslinked with STMP and the general results demonstrated the advantages of the mixed hydrogel.     

Sequential exposure of porcine cumulus cells to FSH and/or LH is critical for appropriate expression of steroidogenic and ovulation-related genes that impact oocyte maturation in vivo and in vitro

In this study, we collected follicular fluid, granulosa cells, and cumulus cells from antral follicles at specific time intervals following equine chorionic gonadotropin (eCG) and human chorionic gonadotropin (hCG) treatment of gilts. The treatment with eCG increased the production of estrogen coordinately with up-regulated proliferation of granulosa and cumulus cells. eCG also induced the expression of LHCGR and PGR in cumulus cells and progesterone accumulation was detected in follicular fluid prior to the LH/hCG surge. Moreover, progesterone and progesterone receptor (PGR) were critical for FSH-induced LHCGR expression in cumulus cells in culture. The expression of LHCGR mRNA in cumulus cells was associated with the ability of LH to induce prostaglandin production, release of epidermal growth factor (EGF)-like factors, and a disintegrin and metalloprotease with thrombospondin-like repeats 1 expression, promoting cumulus cell oocyte complexes (COCs) expansion and oocyte maturation. Based on the unique expression and regulation of PGR and LHCGR in cumulus cells, we designed a novel porcine COCs culture system in which hormones were added sequentially to mimic changes observed in vivo. Specifically, COCs from small antral follicles were pre-cultured with FSH and estradiol for 10 h at which time progesterone was added for another 10 h. After 20 h, COCs were moved to fresh medium containing LH, EGF, and progesterone. The oocytes matured in this revised COC culture system exhibited greater developmental competence to blastocyst stage. From these results, we conclude that to achieve optimal COC expansion and oocyte maturation in culture the unique gene expression patterns in cumulus cells of each species need to be characterized and used to increase the effectiveness of hormone stimulation.     

Parametric Investigation of Viscous Dissipation Effects on Optimized Air Cooling Microchanneled Heat Sinks

The effects of viscous dissipation of working fluid on the optimum heat sink parameters are investigated for the case of air cooling with a micro-/narrow-channeled compact heat sink. For this purpose, an optimization method is introduced first on the basis of dimensionless groups while employing several assumptions. This method yields minimum pumping work or pressure drop with a set of optimized geometric/hydrodynamic parameters when outer dimension of a heat sink and imposed thermal load are specified. Especially for the case of laminar flow, the procedure presents an explicit existence of cooling limit by the viscous heat generation, giving an analytical expression of the maximum removable heat Q max . The relationships between thermal load and each parameter are calculated for both laminar and turbulent regimes under the conditions of compact heat sink dimension (20 mm 2 20 mm 2 2 mm) and circular cross-sectional shape of channels. The results show that the cooling capability under such conditions is largely limited by the salient manifestation of viscous dissipation, when compared with our previous investigation on water cooling presented in [1]. From the discussion, it was concluded that when a micro-/narrow-channeled heat sink is to be designed with air, the effect of viscous dissipation should be taken into account in order to avoid falling on wrong optimum solutions.