Ozonation of CI Reactive Black 5 using rotating packed bed and stirred tank reactor

This study investigates the ozonation of CI Reactive Black 5 (RB5) by using the rotating packed bed (RPB) and completely stirred tank reactor (CSTR) as ozone contactors. The RPB, which provides high gravitational force by adjusting the rotational speed, was employed as a novel ozone contactor. The same ozone dosage was separately introduced into either the RPB or the CSTR for the investigation, while the experimental solution was continuously circulated within the apparatus consisting of the RPB and CSTR. The decolorization and mineralization efficiencies of RB5 in the course of ozonation are compared for these two methods. Moreover, the dissolved and off‐gas ozone concentrations were simultaneously monitored for the further analysis. As a result, the ozone mass transfer rate per unit volume of the RPB was significantly higher because of its higher mass transfer coefficient and gas–liquid concentration driving force. Furthermore, ozonation kinetics was found to be independent of the gravitational magnitude of an ozone gas–liquid contactor. Therefore, the results suggest employing RPBs as ozone‐contacting devices with the advantage of volume reduction. The experimental results, which can be used for further modeling of the ozonation process in the RPB, also show the requirement of correct design for the RPB. Consequently, the present study is useful for the understanding of practical application of RPBs. Copyright © 2004 Society of Chemical Industry     

Multiterminal light-emitting logic device electricallyreprogrammable between OR and NAND functions

A monolithic multiterminal logic device that functions both optically and electrically as an ORNAND gate, is demonstrated for the first time. The device, based on the real-space transfer of hot electrons into a complementary collector layer, has been implemented in an InGaAs/InAlAs/InGaAs heterostructure grown by molecular beam epitaxy. Excellent performance is obtained at room temperature. The collector current and the optical output power both exhibit the OR and the NAND functions of any two of the three input terminals, these functions being interchangeable by the voltage on the third terminal     

The Air is Always Cleaner on the Other Side: Race,Space, and Ambient Air Toxics Exposures in California

Abstract: Environmental justice advocates have recently focused attention on cumulative exposure in minority neighborhoods due to multiple sources of pollution. This article uses U.S. EPA's National Air Toxics Assessment (NATA) for 1996 to examine environmental inequality in California, a state that has been a recent innovator in environmental justice policy. We first estimate potential lifetime cancer risks from mobile and stationary sources. We then consider the distribution of these risks using both simple comparisons and a multivariate model in which we control for income, land use, and other explanatory factors, as well as spatial correlation. We find large racial disparities in California's “riskscape” as well as inequalities by other factors and suggest several implications for environmental and land use policy.     

Laser scanning path generation considering photopolymer solidification in micro-stereolithography

It is essential to automate the scanning path generation process to effectively implement the micro-stereolithography. However, a scanning path that is generated based only on a 3D CAD model introduces dimensional inaccuracies. In micro-stereolithography, the photopolymer solidification is affected by fabrication conditions, such as the optical properties (laser power, laser scanning speed, laser scanning pitch focusing condition, etc.) and material properties of the photopolymer. Thus, the photopolymer solidification phenomena must be considered when generating a laser scanning path. In this paper, a scanning path generation algorithm that uses 3D CAD data and considers the photopolymer solidification phenomena is proposed to improve the dimensional accuracy in micro-stereolithography. Multi-line photopolymer solidification experiments were performed for various laser scanning conditions to examine the photopolymer solidification phenomena. From these experiments, linear relations between the solidification length (width) and scanning length (width) were acquired and stored in a database. Subsequently, these data were utilized to compensate the scanning path of the laser beam. In addition, experiments for determining the layer thickness in the z-direction were performed and these results were also used in the scanning path generation algorithm.This research was supported by the Highly Advanced National Project (http://www.most.go.kr), which performs some of the National R&D Program, and sponsored by the Korean Ministry of Science and Technology under the contract project code M10214000116-02B1500-02010.     

论王光祈的“少年中国”理想

王光祈的“少年中国”理想，是以“少年意大利”为基础，汲取五四时期社会主义思潮的积极成分而形成的。创造“少年中国”在“人”的方面，是从改造中国少年入手，同时注重青年学生与平民的改造，注重劳动阶级、智识阶级与资产阶级的改造与联合；在“事”的方面，积极开展社会事业和社会活动，且必须经过社会分工与国际分工。可见，他的这种理想是典型的社会改革主张，在早期带有无政府主义色彩，自始至终具有强烈的民族主义情感。     

Development and simulation studies of an unsteady state biofilter model for the treatment of cyclic air emissions of an α‐pinene gas stream

This paper describes the development and simulation of an unsteady state biofilter model used to predict dynamic behaviour of cyclically‐operated biofilters and compares it with experimental results obtained from three, parallel, bench‐scale biofilters treating both periodically fluctuating concentrations and constant concentrations of an α‐pinene‐laden gas stream. The dynamic model, using kinetic parameters estimated from the constant concentration biofilter, was able to predict the performance of cyclic biofilters operating at short cycle periods (ie, in the order of minutes and hours). Steady state kinetic data from a constant concentration biofilter can be used to predict unsteady state biofilter operation. At a 24 h cycle period, the dynamic model compared well with experimental results. For long cycle periods (ie, hours and days), removal efficiency decreased after periods of non‐loading: the longer the period of non‐loading, the poorer the biofilter's performance at the re‐commencement of pollutant loading. At longer time scales the model did not effectively predict transient behaviour, as adsorption and changes in kinetic parameters were not accounted for. Modelling results showed that similar biofiltration performance for the cyclic and constant concentration biofiltration of α‐pinene is expected for biofilters operating solely in the first order kinetics regime. Poorer performance for cyclic biofilters following Monod kinetics spanning the entire kinetics range is expected as the cycle amplitude increases. The most important parameters affecting the performance of a cyclically‐operated biofilter with short cycle periods are: amplitude of cyclic fluctuations, C_{g, max}/C_g, relative value of the half‐saturation constant in the Monod expression, K_s, and effective diffusivity of α‐pinene in the biofilm, D_e. Copyright © 2005 Society of Chemical Industry     

Ultrasound‐activated Knoevenagel condensation of malononitrile with carbonylic compounds catalysed by alkaline‐doped saponites

α,β‐Unsaturated nitriles have been synthesized by Knoevenagel condensation of a carbonylic compound with malononitrile, assisted by sonochemical irradiation. Two alkaline‐promoted clays (Li⁺‐ and Cs⁺‐exchanged saponites) have been employed as catalysts. The influence of the carbonylic compound (benzaldehyde or cyclohexanone) and the use of a solvent on the catalytic activity have been studied. Remarkable increase in the conversion values has been found when the reaction is activated by ultrasound, as compared with the thermal activation. In this green, solvent‐free procedure, α,β‐unsaturated nitriles have been produced in very high yields (97%) when the Cs⁺‐saponite is used as catalyst. Copyright © 2004 Society of Chemical Industry     

Investigation of texture effect on visual colour difference evaluation

The texture effect on visual colour difference evaluation was investigated in this study. Five colour centers were selected and textured colour pairs were generated using scanned textile woven fabrics and colour‐mapping technique. The textured and solid colour pairs were then displayed on a characterized cathode ray tube (CRT) monitor for colour difference evaluation. The colour difference values for the pairs with texture patterns are equal to 5.0 CIELAB units in lightness direction. The texture level was represented by the half‐width of histogram, which is called texture strength in this study. High correlation was found between texture strength and visual colour difference for textured colour pairs, which indicates that an increasing of 10 units of texture strength in luminance would cause a decreasing of 0.25 units visual difference for the five colour centers. The ratio of visual difference between textured and solid colour pairs also indicates a high parametric effect of texture. © 2005 Wiley Periodicals, Inc. Col Res Appl, 30, 341–347, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

Effect of specimen size and loading conditions on spalling of concrete

Different qualities of concrete have been fire tested using different geometries of the specimens as well as different load levels and load configurations. The main objective with the study was to examine a test methodology consisting of a full‐scale test and different small scale‐tests for determining the probability of spalling and the amount of spalling of fire exposed concrete structures. A reference specimen was defined as a one‐sided fire exposed slab with the dimensions 1800 × 1200 mm² giving an exposed area of 1500 × 1200 mm². A number of concrete qualities with different probabilities for spalling, were tested using the reference specimen. These tests showed that the reference specimens worked well giving the expected test results. Small specimens were manufactured in different shapes with the same concrete as the one used in the reference tests. These small specimens were tested either at the same time as the reference specimens in the large furnace or afterwards on a small‐scale furnace where the fire exposed surface was 450 × 360 mm². The test results clearly show the increased probability and the increased amount of spalling by using external compressive loading. The results also show that by using pre‐stress through bars or wires the load can be lost due to heating of the bars/wires which results in a decreased amount of spalling. The boundary of the specimen also affects the amount of spalling. The spalling around the edges was in all tests less than the spalling on the central parts of the exposed area. It could also be noted that the spalling did not pass completely through any of the specimens. The reason for this is probably that the water/vapour could migrate out from the unexposed surface of the specimen. Copyright © 2006 John Wiley & Sons, Ltd.