Performance of Indoor Infrared Wireless CDMA Systems with Angle Diversity

Indoor infrared communication systems is one of the possible ways of offering data rates in excess of 100 Mbit/s without the need for wiring. Multiple users can share an infrared channel by code division-multiple access (CDMA) techniques. However, the CDMA system performance is limited by both background noise and co-channel interference. In this paper we study the use of angle diversity for mitigating the effects of the noise and interference. The system considered uses on-off shift keying modulation with multibeam transmitters and imaging receivers. The overall system performance for different diversity combining techniques is evaluated and compared to a system without diversity. Numerical results for a 2-user CDMA system indicate that signal to noise and interference ratio (SNIR) improvement (over systems with no diversity) of 5 dB is obtained for at least 50% of an ensemble of 10000 sample evaluations. The generalized selection combining (GSC)--a new diversity technique yet to be implemented for infrared systems--offers the best performance even with its reduced complexity.     

分布式光纤拉曼放大器的增益平坦设计

介绍了在波分复用（WDM）系统中分布式光纤拉曼放大器（FRA）的理论分析模型。在此基础上，对增益平坦设计所需考虑的因素进行了分析；最后通过试验证明了它的有效性。     

Simultaneous amplification by Er ions and SRS in an Er-doped germano-silica fiber

A flat signal gain over in the entire C- and L-bands by erbium (Er) ions' radiative transition and stimulated Raman scattering in an Er-doped germano-silica fiber can be obtained if proper values of the concentration of Er and background loss in a fiber core are obtained during the fiber fabrication process. The optimized conditions for the flat C- and L-band gain are analyzed as functions of Er concentrations. Even for a low-gain value provided by a germano-silica core fiber with a low Er concentration and an optimum fiber length, a relatively low pump is required to obtain the flat gain band.     

电荷耦合器件积分时间对微型成像系统成像质量的影响

在光圈固定的情况下，确定合适的积分时间对于提高微型电荷耦合器件(CCD)成像系统的成像质量，增强微型飞行器的侦察能力具有十分重要的意义。本文讨论了决定CCD积分时间的各种因素，重点研究了适用于微型飞行器的CCD成像系统的积分时间与像移的关系，并进一步推导了计算像移量的相关数学模型。利用该模型对不同积分时间内采集的运动图像进行了像质评价，结果表明，在保证曝光量的前提下，当像移量被限制在1个像素内时，可以获得相对理想的运动图像像质。     

A New Approach for Built‐in Self‐Test of 4.5 to 5.5 GHz Low‐Noise Amplifiers

This paper presents a low‐cost RF parameter estimation technique using a new RF built‐in self‐test (BIST) circuit and efficient DC measurement for 4.5 to 5.5 GHz low noise amplifiers (LNAs). The BIST circuit measures gain, noise figure, input impedance, and input return loss for an LNA. The BIST circuit is designed using 0.18 μm SiGe technology. The test technique utilizes input impedance matching and output DC voltage measurements. The technique is simple and inexpensive.     

基于AFM的微结构加工实验研究

本文建立了微动工作台和原子力显微镜相结合的微加工系统，在该系统上采用金刚石针尖进行微加工实验，与SPI系统本身的刻划软件刻划出的图形进行了比较分析，得出这个系统适合微结构的加工；并给出了采用该方法加工的1111面及多边形面微结构；还分析了金刚石针尖几何角度及SPM和工作台的相关参数对加工的影响。     

Study on the Complexity of the Bullwhip Effect

Recent years have witnessed a rapid growth of interest in the study of the dynamic behavior of replenishment rules of bullwhip effect. We prove that bullwhip effect and butterfly effect share a same the self-oscillation amplifying mechanism that is the ordering decisions the supplier self-oscillation amplify the perturbations brought by the errors in the processing of retailers' demand information. This results as an explicit self-similar structure of the sensitivity of the system to the initial values duty to the nonlinear mechanism. In this paper, the causes process of the bullwhip effect is described as the internal nonlinear mechanism and study on the complexity of bullwhip effect for order-up-to policy under demand signal processing. The methodology is based on fractal and chaotic theory and allows important insights to be gained about the complexity behavior of bullwhip effect.     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

Development of geometrically exact new shell elements based on general curvilinear co‐ordinates

In the present study first‐order shear deformable shell finite elements based on general curvilinear co‐ordinates are proposed. For the development of the present shell elements, a partial mixed variational functional with independently assumed strains is provided in order to avoid the severe locking troubles known as transverse shear and membrane lockings. Bubble functions are included in the shape function of displacement to improve the performance of the developed element. The proposed assumed strain four‐ and nine‐node elements based on the general tensor shell theory provide an efficient linkage framework for shell surface modelling and finite element analysis. In the several benchmark problems, the present shell elements with exact geometric representations demonstrate their performance compared to previously reported results. Copyright © 2002 John Wiley & Sons, Ltd.     

二氧化锡溅射工艺研究

SnO2 是最早使用也是目前使用最广泛的一种气敏材料 ,使用该材料设计制作的气敏传感器具有许多优点。在简要介绍溅射镀膜的成膜过程和特点的基础上 ,着重介绍了SnO2 膜的制备流程 ,分析了功率和温度变化对成膜质量的影响