Experimental Electronuclear Setup at the Institute of Theoretical and Experimental Physics

The purpose and current construction status, at the Institute of Theoretical and Experimental Physics, of an experimental electronuclear setup, combining a pulsed proton linear accelerator (36 MeV, 0.5 mA) and a subcritical blanket thermal-power assembly 100 kW, are discussed. The main equipment is already available or is being built in industry. The setup can be used to investigate the dynamics of the interaction of a linac–driver and a subcritical reactor and problems concerning the accelerator–driver and the target–blanket assembly. The proton beams and neutron fluxes will be used for applied purposes. In the future it will be possible to increase substantially the current and energy of the proton beam.     

The structure and properties of a Cr<Subscript>3</Subscript>C<Subscript>2</Subscript>-Ni coating deposited by a high-velocity plasma jet onto a copper substrate

Chromium carbide-nickel coatings were deposited onto a technical grade copper substrate by means of a high-velocity plasma jet of a plasmatron operating in specially selected regimes. An analysis of the coatings showed evidence of the formation of a Ni-based solid solution, a complex chromium carbide (Cr₇C₃), and an fcc crystal phase with a lattice parameter of 3.614 Å. The surface of the coatings exhibits a characteristic relief resulting from a dynamic interaction between melted and fused particles of the initial powder. The local hardness on some areas of the surface and in depth of the coating reaches 66±4.5 HRC, while the coating adhesion strength varies from 25 to 300 MPa.     

Trellis and convolutional precoding for transmitter-based interference presubtraction

This paper studies the combination of practical trellis and convolution codes with Tomlinson-Harashima precoding (THP) for the presubtraction of multiuser interference that is known at the transmitter but not known at the receiver. It is well known that a straightforward application of THP suffers power, modulo, and shaping losses. This paper proposes generalizations of THP that recover some of these losses. At a high signal-to-noise ratio (SNR), the precoding loss is dominated by the shaping loss, which is about 1.53 dB. To recover shaping loss, a trellis-shaping technique is developed that takes into account the knowledge of a noncausal interfering sequence, rather than just the instantaneous interference. At rates of 2 and 3 bits per transmission, trellis shaping is shown to be able to recover almost all of the 1.53-dB shaping loss. At a low SNR, the precoding loss is dominated by power and modulo losses, which can be as large as 3-4 dB. To recover these losses, a technique that incorporates partial interference presubtraction (PIP) within convolutional decoding is developed. At rates of 0.5 and 0.25 bits per transmission, PIP is able to recover 1-1.5 dB of the power loss. For intermediate SNR channels, a combination of the two schemes is shown to recover both power and shaping losses.     

基于DICOM标准全方向M型心动图的软件系统设计

本文介绍了基于DICOM标准全方向M型心动图软件系统的设计方案,详细分析了系统结构及各个模块功能.通过该系统可以直接准确地定量检测分析心脏各结构的舒、缩、形变过程及其数据,同时可以生成多个任意方向且互相同步的M型心动图.各个模块设计完全遵循DICOM标准,同时结合数据库管理,方便查询索引.该系统分析的影像数据可以来自PACS服务器,也可以来自本地系统,分析结果数据可以回传PACS服务器,也可以保存本地.该系统实现了国家发明专利"全方向M型心动图方法及其系统98 125713.5"系统数据和国际医学图像传递标准的接口.     

Study of thermal effects and self-heating phenomena in planar power SOI MOS transistors

Heat removal problems, thermal effects, and self-heating phenomena occurring during operation of planar power SOI MOS transistors are considered. Using device-technological simulating methods, the transistor characteristics and safe operation range were studied. It was shown that limitations of the safe operation range are mostly associated with structure self-heating rather than with the parasitic bipolar transistor.     

中国铁通企业信息化战略规划和措施

首先简单回顾了中国铁通成立之初计费管理系统的一期建设和二期扩容后支撑能力的明显不足,以及信息化建设初期各部门独立IT系统运行中的问题,然后较详细介绍了企业信息化规划的整体思路.包括业务系统和流程、组织和业务流程重组、信息技术战略和架构等.并在实践的基础上,列举了信息化系统实施过程中应避免的做法和应注意的事项.     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

The cooling and solidification of melted drops during their movement in an immiscible cooling medium is widely employed for granulation in the chemical industry, and a study of these processes to provides a basis for the design of the granulation tower height and the temperature of the cooling medium is reported. A physical model of the cooling and solidification of the drop is established and the numerical calculation is performed. The influences of the key factors in the solidification, i.e., Bi number, drop diameter, temperature of the cooling medium, etc. are presented. The cooling and solidification during wax granulation in a water‐cooling tower and during urea granulation in an air‐cooling tower (spraying tower) are described in detail. Characteristics of the solidification and temperature distribution within the particle at different times are shown. The model and calculations can be used for structure design of the granulation tower and optimization of the operation parameters.