Investigation of the cyanide leaching optimization for ultrafine grinding gold–silver ore

ABSTRACT

In recent years, the ultrafine grinding (UFG) process has become increasingly important for the recovery of precious metals (especially for Au and Ag) from raw ores. It is well known that cyanide leaching of gold–silver ore has been an accepted process in the world. In the current study, UFG was proposed as a pretreatment method prior to cyanide leaching of a gold–silver ore. First, the ore was crushed and ground by jaw, cone crusher, and ring mill, respectively. Particle size of ground product was 75 µm based d₈₀. Second, the fine product was subjected to the grinding process by vertical wet stirred ball mill, and the final ultrafine product was used as leach feed material. The leach feed material had about d₈₀ = 20 µm and d₅₀ = 6.02 µm particle size. Some important leaching parameters were optimized by using the ultrafine powder in the study. The final leach experiments demonstrated that the recoveries of Au and Ag were 91.92% and 82.15% under optimum leaching conditions such as 150 kg/t quicklime dosage, 25% pulp density, 85°C leach temperature, 500 g/t cyanide concentration, and 90 h leaching time.     

Effects of cavity disinfectants on bond strength of an etch-and-rinse adhesive to water- or ethanol-saturated sound and caries-affected dentin

Objective: To evaluate the effect of cavity disinfectants on the immediate microtensile bond strength (μTBS) of an etch-and-rinse adhesive to water- and ethanol-saturated sound and caries-affected dentin (CAD). Material and Methods: Thirty-six human molars were sectioned to expose 1/3 of the mid-coronal dentin surface. Sound (n = 18) and CAD (n = 18) specimens were divided into six groups each (n = 3): one positive control (sound), one negative control (CAD), and five experimental groups each. In the control group, dentin surfaces were bonded using an etch-and-rinse adhesive with a traditional water-wet bonding technique. In the experimental groups, ozone was applied before etching and chlorhexidine after etching. In the ethanol-wet bonding groups, acid-etched dentin surfaces were treated with ethanol. Following adhesive application and composite buildups, bonded specimens were sectioned to form sticks. Failure modes were analyzed using a stereomicroscope. Results: The water-wet bonded sound control group yielded the highest μTBS among all groups (p < 0.001). The lowest μTBS values were observed in the ozone groups (p < 0.05). The ethanol-wet bonded CAD group exhibited a higher μTBS than the water-wet bonded negative controls. Although compared to the positive control, chlorhexidine decreased the μTBS (p < 0.05), an increase with no significant difference was observed in the negative control (p > 0.05). Conclusions: The μTBS values of CAD were lower than those of sound dentin. Ethanol-wet bonding improved the μTBS of CAD. Ozone application reduced the μTBS in both sound and CAD; chlorhexidine improved the immediate μTBS after etching in CAD.     

Determination of the Optimum NiS Fire Assay Parameters for Pt,Pd, and Rh in Automotive Exhaust Catalytic Converters

This work investigates the performance of the nickel sulfide fire assay (NiS-FA) for the pyrometallurgical analysis of platinum group elements (PGEs) from mixtures of automotive exhaust catalytic converters (e.g., gasoline, diesel, and diesel particular filter) by assessing the effects of various flux materials and reaction parameters on platinum, palladium, and rhodium recovery. Inductively coupled plasma mass spectrometry and atomic absorption spectroscopy (AAS) are used for the analysis of the NiS-FA beads. We found that the optimum recovery (at least 99.0%) was achieved with reaction of 11.5 g of flux (0.53 w/w ratio, sodium tetraborate:sodium carbonate), 1 g nickel, and 0.84 g sulfur (1.2 w/w ratio, Ni:S) per gram of sample for 90 min at 975°C. Reference standards (NIST SRM 2557) were used to compare efficiencies and identify the optimum conditions. The results are consistent with certified values and PGEs could be recovered within the 95% confidence level. The precision (<4.0% RSD) of all measurements, expressed as percentage relative standard deviation (SD), ranged up to 3.0%.     

Al–Ti–B grain refiners via powder metallurgy processing of Al/K2TiF6/KBF4 powder blends

The response to thermal exposure of ball-milled Al/K₂TiF₆/KBF₄ powder blends was investigated to explore the potential of PM processing for the manufacture of Al–Ti–B alloys. K₂TiF₆ starts to be reduced by aluminium as early as 220 °C when ball-milled Al/K₂TiF₆/KBF₄ powder blends are heated. The reaction of KBF₄ with aluminium follows soon after. The Ti and B thus produced are both solutionized in aluminium before precipitating out as Al₃Ti and TiB₂. All these reactions take place below the melting point of aluminium. The ball-milled Al/K₂TiF₆/KBF₄ powder blends heat treated at approximately 525 °C can be compacted to produce Al–Ti–B pellets with in situ formed Al₃Ti and TiB₂ particles. These pellets are shown to be adequate grain refiners for aluminium alloys.     

Analysis of macro segregation in twin-roll cast aluminium strips via solidification curves

A porous NiO/yttria-stabilized zirconia (YSZ) anode substrate for zirconia-based tubular solid oxide fuel cells (SOFCs) was prepared by the gelcasting. The effect of the impregnation of SDC in the substrate was studied. Electrochemical impedance spectroscopy and I–V and I–P curves of the cells were measured. Scanning electron microscopy (SEM) was used to observe the microstructures. The results indicate that the performance of the cell can be significantly improved by incorporating the nano-structured SDC particles in the substrate. The peak power density of the cell is increased by about 60% and the area specific resistance (ASR) decreased by about 47% at 700 °C, compared with the unmodified cells. It is explained as the extended triple-phase boundary (TPB) in the anode substrate and the excellent electrocatalytic property of SDC. It is also found that the nano-scale SDC particles change a lot during the reduction of the anode substrate, and the morphology of the resultant SDC particles on the metal Ni is significantly different from that on the YSZ. After the long-term operation, the morphology of the SDC particles on the Ni changes again, but that on the YSZ keeps almost unchanged.     

Injectable solid hydrogel: mechanism of shear-thinning and immediate recovery of injectable β-hairpin peptide hydrogels

β-Hairpin peptide-based hydrogels are a class of injectable hydrogel solids with significant potential use in injectable therapies. β-hairpin peptide hydrogels can be injected as preformed solids, because the solid gel can shear-thin and consequently flow under a proper shear stress but immediately recover back into a solid on removal of the stress. In this work, hydrogel behavior during and after flow was studied in order to facilitate fundamental understanding of how the gels flow during shear-thinning and how they quickly recover mechanically and morphologically relative to their original, pre-flow properties. While all studied β-hairpin hydrogels shear-thin and recover, the duration of shear and the strain rate affected both the gel stiffness immediately recovered after flow and the ultimate stiffness obtained after complete rehealing of the gel. Results of structural analysis during flow were related to bulk rheological behavior and indicated gel network fracture into large (>200 nm) hydrogel domains during flow. After cessation of flow the large hydrogel domains are immediately percolated which immediately reforms the solid hydrogel. The underlying mechanisms of the gel shear-thinning and healing processes are discussed relative to other shear-responsive networks like colloidal gels and micellar solutions.     

False positive pleural biopsy and high CA125 levels in serum and pleural effusion in systemic lupus erythematosus

A 23-year-old female with systemic lupus erythematosus is reported. The clinical features included fever, shortness of breath, lymphadenopathies, hepatosplenomegaly, pleural and pericardial fluids, ANA and Anti-DNA positivity. Pleural biopsy was false positive for malignancy on two occasions. High CA125 levels were detected in both serum and pleural fluid. Following prednisolone treatment, clinical and laboratory findings returned to normal.     

Response of normal aorta to endovascular grafting: a serial histopathological study

The initial data on the effect of ruthenium red on mature human type-1 VDAC are presented. Highly enriched human type-1 porin in planar lipid bilayers shows lowered voltage-dependence whenever a commercially available ruthenium red preparation is applied. The hexavalent polycationic dye ruthenium red affects different functions in varying cell compartments. Concerning the plasma membrane of cells the actual data, together with our former measurements on the interaction of VDAC and the polycationic synthetic polyamine Compound 48/80, refer to a second VDAC opener, which is relevant for studies on the stimulation of exocytotic processes of different cell types.     

Microstructural characterization of a rapidly-solidified Al-12 wt% Si alloy

Optical, electron metallography and X-ray diffraction techniques were employed to characterize the microstructure of a rapidly solidified Al-12 wt% Si alloy. Ribbons produced with the planar flow casting process at a cooling rate of 10⁶ Ks^–1, had a very fine cellular structure of Al and nanosize Si particles which are distributed inside and at the boundaries of these cells. Thinner sections (t<30 m) have apparently experienced higher cooling rates and show, in addition to a cellular structure, a distinct zone which is featureless at optical microscope magnifications.