Interfacial tension of demixed polymer solutions near the critical temperature: polystyrene + methylcyclohexane

Interfacial tension between demixed solutions of polystyrene + methylcyclohexane has been measured near the critical temperature as a function of temperature using polystyrenes with molecular weights 9000 ～ 1.26 × 10⁶. The critical exponent for the interfacial tension was determined to be about 1.30 for the lower molecular weight systems. However, for higher molecular weights the exponent could not be obtained because the system departed from critical behaviour. Magnitudes of the interfacial tension were proportional to about N^?0.44, where N is the polymerization index. Experimental results were compared with the recently-proposed theories and found to be in qualitative agreement. The tricritical theory of polymer solutions was also compared with the experimental results.     

A superconducting filter to separate an oxygen and argon mixture

Hot isostatic pressing in an oxygen atmosphere, known as O₂-HIP method, has been used successfully to synthesize oxide materials, as well as to produce porous materials. In this paper a porous superconducting oxide is synthesized by this method and its application as a gas filter is described. Porous superconductors can be used to separate a mixture of paramagnetic and diamagnetic gases, such as oxygen and argon. Separation occurs after a magnetic field is applied and is based on the Meissner effect. Experimental results showed that the oxygen content of an oxygen/argon mixture increased after passing through a filter with large pore size (about 10 m).     

Additional kernel observer: privilege escalation attack prevention mechanism focusing on system call privilege changes

International Journal of Information Security - Cyberattacks, especially attacks that exploit operating system vulnerabilities, have been increasing in recent years. In particular, if administrator...     

Chromium-nitride in situ composites with a compositional gradient formed by reactive DC plasma spraying

Nitrides of transition metals have good wear- and corrosion-resistant properties because of their high hardness and chemical stability. Chromium-nitride coatings can be deposited by ion plating; however, the thin thickness due to the slow deposition rate must be improved for severe wear-resistant applications. The main objective in this paper is to realize good structural control in the processing of chromiumnitride in situ composite coatings formed at a high deposition rate. They were synthesized by reactive low-pressure plasma spraying using elemental chromium powder as a spray material. The transferred arc between the gun electrode and the substrate was used to accelerate the nitriding reaction. The sprayed coatings consist of chromium, Cr₂N, and CrN, which have a composition gradient from the substrate interface to the surface. The volume fraction of Cr₂N increases with transferred arc current, and nonreacted chromium concurrently decreases, except close to the substrate. The CrN phase, however, only exists as a surface layer of 20 to 30 μm because it is decomposed to Cr₂N above 1420 K. The hardness of the composite coatings depends on the volume fraction of Cr₂N, and it increases to 1300 HV at a Cr₂N volume fraction of 0.98. The seizure stress with lubricant depends on the coating hardness. The maximum seizure stress of 24.9 MPa is obtained at a hardness of 1300 HV. The composite coatings also show a superior wear resistance. Hence, the Cr₂N in situ composite coatings synthesized by reactive plasma spraying with transferred arc are expected to be good candidates for wear-resistant applications.     

Microstructure development of steel during severe plastic deformation

The microstructure development during plastic deformation was reviewed for iron and steel which were subjected to cold rolling or mechanical milling (MM) treatment, and the change in strengthening mechanism caused by the severe plastic deformation (SPD) was also discussed in terms of ultra grain refinement behavior. The microstructure of cold-rolled iron is characterized by a typical dislocation cell structure, where the strength can be explained by dislocation strengthening. It was confirmed that the increase in dislocation density by cold working is limited at 10¹⁶m⁻², which means the maximum hardness obtained by dislocation strengthening is HV3.7 GPa. However, the iron is abnormally work-hardened over the maximum dislocation strengthening by SPD of MM because of the ultra grain refinement caused by the SPD. In addition, impurity of carbon plays an important role in such grain refinement: the carbon addition leads to the formation of nano-crystallized structure in iron.     

Polytetrafluoroethylene processing characteristics using high-energy X-ray

Polytetrafluoroethylene (PTFE) microstructures’ processing characteristics using X-ray photo dcomposition and desorption are studied in the highest energy region (2 keV to >12 keV). While the exposed surface states are seen melting and boiling from the remaining bubble structure of the irradiated surface, basic photochemistry of PTFE is also same as previous reports and high-aspect ratio structures are successfully formed. We developed new Ni stencil electroformed stencil masks and successfully fabricated first and practical example of PTFE micro fluidic parts. The characteristics of fabricated micro fluidic parts, a PTFE fluid filter for vertical fluid flow operation which works as passive valve, agreed with the calculated results. This suggests that the accuracy of patterning is adequate to apply this technique to fabricate microfluidic parts and other various microparts.     

Enzyme-linked immunosorvent assay using vertical microreactor stack with microbeads

The advantages of vertical microreactor stack with three-dimensional (3D) structure for immunoassay are discussed. The vertical microreactor stack uses vertical fluid flow operation with multifunctional fluid filters. The multi function of fluid filter is very effective for micromixing and passive valve operation. The mechanism of micromixing is discussed by using computational fluid dynamics (CFD), and we know that the mixing mechanism based on Coanda effect. To evaluate the micromixing performance of fluid filter, we demonstrated enzyme reaction with unique repeat mixing operation. As the results, we proved that the fluid filter has very effective mixing performance. The detection limit, which demonstrated by competition enzyme-linked immunosorvent assay (ELISA), is comparable with recommended detection limit, which suggested by Japanese ministry for the environment.     

A low wall-loading DEMO reactor design with high priority for early and reliable realization of a tokamak fusion reactor over the cost performance

Based on scientific databases adopted for designing ITER plasmas and on the advancement of fusion nuclear technology from the recent R&D program, a low wall-loading DEMO fusion reactor has been designed, where high priority has been given to the early and reliable realization of a tokamak fusion plasma over the cost performance. Since the major radius of this DEMO reactor is chosen to be 10 m, plasma ignition is achievable with a low fusion power of 0.8 GW and an operation period of 4–5 hours is available only with inductive current drive. The low ignition power makes it possible to adopt a first wall with an austenitic stainless steel, for which significant databases and operating experience exists, due to its use in the presence of neutron irradiation in fission reactors. In step with development of advanced materials, a step-wise increase of the fusion power seems to be feasible and realistic, because this DEMO reactor has the potential to produce a fusion power of 5 GW.