Application results of a prototype ultrasonic liquid film sensor to a 7 MPa steam–water two-phase flow experiment

A prototype ultrasonic liquid film sensor was applied to a high-temperature steam–water two-phase flow experiment. The liquid film sensor was vertically installed in a loop which was connected to HUSTLE, a multi-purpose steam source test facility. The hydraulic diameter of the measurement section was 9.4 mm. The output waveforms of the sensor were acquired with a digital oscilloscope. The fluid temperature and system pressure were kept at 288 °C and 7.2 MPa, respectively, during the experiment. The pulse-echo method was used to calculate the liquid film thickness. The cross-correlation calculation was utilized to determine the time difference between the pulse reflected at the sensor surface and the pulse reflected at the liquid film surface. The time-averaged liquid film thicknesses were less than 0.055 mm in the annular flow condition. The increase of the time-averaged thickness was small with the change of the gas momentum flux. The film thicknesses measured with the sensor were compared with the past experimental results; the former were smaller than one-fourth of the thickness estimated as the mean film thickness. The comparison results suggested that the continuous liquid sublayer thickness was measured with the liquid film sensor.     

First law analysis for viscous dissipation in liquid flows in micro-channels

This paper focuses on temperature rise due to the viscous dissipation in liquids flowing through micro-channels. In the past, equations for the prediction of the temperature rise have been obtained as a function of the friction factor, Reynolds number and Eckert number or a similar form, starting from Navier–Stokes equation and energy equation under the assumption of fully developed laminar flow by researchers. The temperature rises calculated from the equations have been compared with experimental data and the equations have been validated. However, in this paper, a new equation for the prediction of the temperature rise is simply obtained from the first law of thermodynamics without restriction of fully developed laminar flow.     

Preparation of ultrafine polyurethane fiber web by laser‐electrospinning combined with air blowing

Thermoplastic polyurethane fiber webs were prepared using a laser‐heated electrospinning process combined with air blowing. The effect of spinning conditions such as air flow rate and air temperature on fiber diameter and molecular weight was investigated. Although the average fiber diameter decreased with increased air flow rate at each air temperature, the diameter increased when the air flow rate was >15 NL min^?1. In addition, the fiber was comparatively thicker with an increase in the air temperature. The variation in the fiber diameter tends to increase with the air flow rate, and a reduction in the molecular weight of the fiber by thermal degradation was suppressed. The thinnest and most uniform fiber with a diameter of 0.9 µm and a diameter coefficient variation of 15% was obtained at an air temperature of 25°C under an air flow rate of 15 NL min^?1. This fiber also had a minimum of decreased molecular weight. POLYM. ENG. SCI., 54:2605–2609, 2014. © 2013 Society of Plastics Engineers     

Thickness estimation of interface films formed on Li1−xCoO2 electrodes by hard X-ray photoelectron spectroscopy

Solid electrolyte interface (SEI) films formed on Li_1−xCoO₂ electrodes were observed with hard X-ray photoelectron spectroscopy (HX-PES). This paper particularly focuses on film thickness estimation using HX-PES with theoretical calculation. The validity of the calculation was proven by experiments using model SEI films. The native film formed on a LiCoO₂ composite electrode was estimated to be LiF with its thickness of 5 nm. Formation of Co (II) species on top of LiCoO₂ was also indicated. Storage of the electrode at 60 °C brought about considerable film growth (30-40 nm) with carbonate compounds formation. SEI film changes during charging of the LiCoO₂ electrode were also examined. The main component in the film was deduced to be LiF or a kind of fluorite, with its thickness decreased during charging. The SEI formation mechanisms are also elucidated.     

Structure and mechanical properties of multi‐hollowed fibers produced by CO2 laser irradiated neck drawing

Multi‐hollowed fibers with a hollowness ratio of over 20% were successfully produced using a neck‐drawing technique accompanied by CO₂ laser irradiation on unoriented and amorphous polytrimethylene terephthalate (PTT) fibers with diameters of approximately 104 µm. The structure and mechanical properties of the multi‐hollowed fibers were characterized using scanning electron microscopy, wide angle X‐ray diffraction (WAXD), birefringence measurements, and tensile tests. Crystal orientation factors in the direction normal to the (010) and (002) planes, which were obtained from WAXD patterns, were lower in comparison to values obtained in previous studies on fibers that did not feature these hollows [9] because of the development of these internal hollows. The PTT fibers in this study also displayed high toughness, about 465 MPa (3.5 cN/dtex) strength and about 40% elongation, and had excellent elastic recovery (>95%) after 10 stretch cycles. POLYM. ENG. SCI., 56:609–616, 2016. © 2015 Society of Plastics Engineers     

Discovery of a Novel Scaffold as an Indoleamine 2,3‐Dioxygenase 1 (IDO1) Inhibitor Based on the Pyrrolopiperazinone Alkaloid,Longamide B

Indoleamine 2,3‐dioxygenase 1 (IDO1) has emerged as a key target for cancer therapy, as IDO1 plays a critical role in the capacity of tumor cells to evade the immune system. The pyrrolopiperazinone alkaloid longamide B and its derivatives were identified as novel IDO1 inhibitors based on docking studies and small library synthesis. The thioamide derivative showed higher IDO1 inhibitory activity than longamide B, and displayed an activity similar to that of a representative IDO1 inhibitor, 1‐methyl‐tryptophan. These results suggest that the pyrrolopiperazinone scaffold of longamide B could be used in the development of IDO1 inhibitors.     

Cerebral Hyperperfusion after Revascularization Inhibits Development of Cerebral Ischemic Lesions Due to Artery-to-Artery Emboli during Carotid Exposure in Endarterectomy for Patients with Preoperative Cerebral Hemodynamic Insufficiency: Revisiting the “Impaired Clearance of Emboli” Concept

The purpose of the present study was to determine whether cerebral hyperperfusion after revascularization inhibits development of cerebral ischemic lesions due to artery-to-artery emboli during exposure of the carotid arteries in carotid endarterectomy (CEA). In patients undergoing CEA for internal carotid artery stenosis (≥70%), cerebral blood flow (CBF) was measured using single-photon emission computed tomography (SPECT) before and immediately after CEA. Microembolic signals (MES) were identified using transcranial Doppler during carotid exposure. Diffusion-weighted magnetic resonance imaging (DWI) was performed within 24 h after surgery. Of 32 patients with a combination of reduced cerebrovascular reactivity to acetazolamide on preoperative brain perfusion SPECT and MES during carotid exposure, 14 (44%) showed cerebral hyperperfusion (defined as postoperative CBF increase ≥100% compared with preoperative values), and 16 (50%) developed DWI-characterized postoperative cerebral ischemic lesions. Postoperative cerebral hyperperfusion was significantly associated with the absence of DWI-characterized postoperative cerebral ischemic lesions (95% confidence interval, 0.001–0.179; p = 0.0009). These data suggest that cerebral hyperperfusion after revascularization inhibits development of cerebral ischemic lesions due to artery-to-artery emboli during carotid exposure in CEA, supporting the “impaired clearance of emboli” concept. Blood pressure elevation following carotid declamping would be effective when embolism not accompanied by cerebral hyperperfusion occurs during CEA.     

On-off switching properties of one-dimensional photonic crystals consisting of azo-functionalized polymer liquid crystals having different methylene spacers and polyvinyl alcohol

In this paper, photoresponsive behavior of multi-bilayered films having precisely controlled layer thickness prepared by stacking an azo-functionalized polymer liquid crystal, PMAzXAc, and polyvinyl alcohol alternatively, PVA, is described. The multi-bilayered films were found to reflect a light of specific wavelength depending on the layer thickness and refractive index, and showed the reversible change in the reflection intensity by irradiation with visible and UV lights. The change in the reflection intensity was brought about by change in the molecular orientation of PMAzXAc between an out-of-plane orientation and a photo-induced isotropic state, and was strongly dependent on the number of methylene spacer of PMAzXAc linking the azobenzene side group with the acrylate polymer main chain. PMAz6Ac with hexa-methylene spacer showed the largest change in the reflection intensity, while smaller change in the reflection intensity was observed for PMAzXAc having shorter or longer methylene spacer than 6. The effect of the methylene spacers on the photochemical change in the molecular orientation of azobenzene chromophores in the multi-bilayered films will be discussed.