Analysis and comparison of two-dimensional permanent-magnet arrays for planar motor

This paper investigates three kinds of permanent-magnet arrays used in planar motors with polarity centers distributed in the lattices of a matrix. The magnetic field of every kind of magnet array is analyzed by analytical methods. First, we give a Laplace equation of magnetic scalar potential and a series of boundary conditions. Then, we derive the analytical expressions of magnet field strength and magnet flux density in the air gap of each kind of magnet array by the method of separation of variables. Finally, we compare the three types of magnet arrays on the basis of the analytical solutions.     

EPP在便携式数据采集系统中的应用

分析了并口处于EPP(增强型并行端口)模式时和单片机进行数据交换的原理.介绍了有关EPP的基本特性、信号定义、操作模式及其程序设计方法,设计了基于EPP协议的便携式数据采集系统,给出了技术解决方案,讨论了系统的硬件接口电路和软件编程.方案具有可靠性高、速度快、软硬件设计简捷等优点.     

Structure and catalytic properties of dealuminated modified zeolites Y

The effect of treatment with a zirconyl nitrate aqueous solution on the structure; the hydroxyl-layer constitution; and the adsorptive, acid, and catalytic properties of dealuminated zeolite Y was studied. The zeolite was prepared by boiling NH₄Y in an ethylenediaminetetraacetic acid disodium salt solution followed by ion exchange with ammonium chloride and calcination in a 100% steam flow at 750°C. X-ray diffraction, IR spectroscopy, and DTA data show the formation of an ultrastable form of zeolite Y. The incorporation of zirconium in zeolite led to an increase in the proportion of strong acid sites, thus raising the yield of cracking products during n-hexane conversion tested on platinum-containing catalyst samples.     

碳纤维复合材料柔性连续抽油杆开发及应用

碳纤维柔性连续抽油杆选用高性能碳纤维 ,以环氧树脂胶液为基体材料 ,添加一定配比的固化剂、促进剂和脱模剂 ,采用拉挤成型工艺制成 ,其开发的关键技术是连续成型、连接接头和安全保险装置。现场应用试验表明 ,TXC— 1、TXC— 2、TXC— 3三种规格的碳纤维柔性连续抽油杆能可靠应用于泵挂深度分别为 12 0 0、 180 0、 30 0 0m的直井和斜井中 ,实测比钢抽油杆节电 ,日产油量提高 。节能增产效果显著。     

Structure and Certain Properties of Hot-Pressed Boron Carbide-Based Ceramic with Calcium-Silicon Additive

The influence which the composition of powder mixtures, the treatment conditions which the mixtures are subjected to, and the conditions under which the hot-pressed composite materials B₄C – (5-10 mass%) calcium-silicon are fabricated exert on the structure, nature of failure, and mechanical properties of these materials is investigated. Optimum properties are possessed by material containing 10 mass% of addition. It is shown that the structure, morphology, and dispersivity, as well as the nature of the distribution of the components that are added to the composite material (secondary phase) vary as the temperature of hot pressing changes. Maximal mechanical characteristics of the composite material (σ_bend = 560 MPa, K _1c = 4.7 MPa·m^1/2, HV = 37 GPa) are attained at hot-pressing temperatures in the range 2000-2100°C.     

芳烃抽提装置技术改造

由于中国石化锦西石化分公司600kt／a连续重整装置的建设，芳烃抽提装置的原料由原来的脱戊烷油变为Ce组分。为此，对抽余油水洗塔和芳烃分离部分的苯塔塔盘，以及苯塔塔顶和塔底抽出部分进行了改造，更换部分机泵和增加变频泵，并将常规仪表改为DCS控制。改造后装置实现一次开车成功，生产出合格产品。抽余油中总芳烃含量小于0．1％，苯回收率达到99%以上。     

Convective transfer processes in chemically stable and reacting liquids with an internal structure

Dynamic processes are studied in media with softly and hardly internal destroyable configurations. A method is examined for the measurement of properties of media with spatial separation of the chemical transformation stages and thermal hydrodynamic measurements.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 53, No. 5, pp. 781–789, November, 1987.     

Fabrication of Strain-Relaxed Si<Subscript>1 − <Emphasis Type="Italic">x</Emphasis></Subscript>Ge<Subscript>x</Subscript>/Si(001) Buffer Layers of Low Surface Roughness

The results are presented of the fabrication of strain-relaxed graded Si_{1 − x} Ge_x/Si(001) buffer layers with a maximum Ge fraction of about 0.25 that have a low density of threading dislocations (<10⁶ cm⁻²) and low surface roughness. The buffer layers are grown by atmospheric-pressure hydride CVD. It is found that chemical mechanical polishing can reduce their surface roughness to a level comparable with that of the original Si(001) substrates. It is shown that the polished buffer layers can serve as substrates for MBE-grown SiGe/Si heterostructures.__________Translated from Mikroelektronika, Vol. 34, No. 4, 2005, pp. 243–250.Original Russian Text Copyright © 2005 by Vostokov, Drozdov, Krasil’nik, Kuznetsov, Novikov, Perevoshchikov, Shaleev.