Formation of C49-TiSi2 in flash memories: a nucleation controlled phenomenon?

The formation of Ti silicides has been examined in flash memories with 0.25 μm linewidth by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. It has been observed that, after the first rapid thermal process and the selective metal etch, there is no silicide on the source and on a majority of drain contacts while C49-TiSi₂ is found on the gate. A pre-amorphisation implant increases drastically the formation of C49-TiSi₂ in the drain zone while modifications of annealing conditions have little impact. These results indicate that the formation of C49-TiSi₂ is most likely controlled by nucleation and that this nucleation is sensitive to both the width and the length of the reaction zone. The formation of a Ti rich silicide may play an important role in this nucleation by decreasing the driving force for the formation of C49-TiSi₂. Curiously enough, the formation of C49-TiSi₂ appears thus as a major concern for the salicide process in flash memories.     

Pile Response Adjacent to Braced Excavation

The excavation of soil for the construction of basements or cut-and-cover tunnels results in ground movements. One particular concern is that the excavation-induced lateral soil movements may adversely affect any nearby pile foundation. The lateral loads imposed by the soil movements induce bending moments and deflections in the pile, which may lead to structural distress and failure. This paper presents the results of an actual full-scale instrumented study that was carried to examine the behavior of an existing pile due to nearby excavation activities resulting from the construction of a 16 m deep cut-and-cover tunnel. The pile was located 3 m behind a 0.8 m thick diaphragm wall. Excavation to the formation level that was 16 m below the ground surface resulted in a maximum lateral pile movement of 28 mm. A simplified numerical procedure based on the finite-element method was used to analyze the pile response. Generally, the theoretical predictions were in reasonable agreement with the measured results.     

Microstructural and textural characterization of a hot-rolled IF steel

The present paper reports the experimental results on the microstructural and textural characterization of a hot-rolled IF steel. The IF steel was hot-rolled in multiple passes in the austenitic field (1,070 °C) followed by air-cooling. SEM, TEM, and LOM were used to image the microstructure of the material. The global texture was determined by X-ray diffraction (XRD) technique. The mesotexture of selected regions was investigated by electron backscatter diffraction (EBSD). Results show the presence of a diffuse (nearly random) and weak texture in the hot-band that consists of recrystallized polygonal grains and subgrains. The fraction of boundaries with misorientations comprised in the interval 2° ≤ ψ < 15° was found to be lower than 5%. It can be concluded that these low angle boundaries and the presence of subgrains can be associated to the existence of a few areas softened by recovery during or after hot rolling in austenitic field.     

Methodologies for characterizing traffic in wide area networks: Analysis and benchmarking

Since computer networks play an important role in distributed computing environments, an application's performance depends heavily on the quality of service provided by the communication networks. To ensure a high performance, the characteristics of wide area networks, WANs, must be well understood. This paper presents methodologies to characterize WAN traffic based on real measurements from Bellcore's backbone network that connects remote sites using dedicated T1 links. This paper also suggests some workload models that can be used for wide area network sizing and performance evaluation studies. It is found that the inter-site traffic pattern depends on the time of the day and the day of the week. Furthermore, the traffic between two sites is found to be reasonably symmetric, except for those sites designated as back-up sites. The coefficient of variation is used as a measure for the traffic burstiness and it is found to be 1·5 degree during working hours. The methods presented here are easy to use and cost-effective.     

Evaluation of solid-desiccant-based evaporative cooling cycles for typical hot and humid climates

This paper presents an evaluation of various solid desiccant cycles for air conditioning in hot and humid climates. Psychometric evaluation of potential cycles for 16 typical Indian cities has been carried out with the objective of achieving standard comfort conditions in the room. Computer simulation is based on constant effectiveness of heat exchangers and evaporative coolers and actual performance data of a commercially available desiccant wheel dehumidifier. The influence of various outdoor conditions, the effectiveness of heat exchangers/evaporative coolers on the cooling coefficient of performance and volumetric air flowrate per unit cooling capacity have been investigated. It is found that amongst ventilation, recirculation and Dunkle cycles, the Dunkle cycle is better for a wide range of outdoor conditions. However, cycles using wet surface heat exchangers give even higher performance.     

Efficient dissemination of personalized information using content-based multicast

There has been a surge of interest in the delivery of personalized information to users (e.g., personalized stocks or travel information), particularly as mobile users with limited terminal device capabilities increasingly desire updated and targeted information in real time. When the number of information recipients is large and there is sufficient commonality in their interests, as is often the case, IP multicast is an efficient way of delivering the information. However, IP multicast services do not consider the structure and semantics of the information in the multicast process. We propose the use of Content-Based Multicast (CBM) where extra content filtering is performed at the interior nodes of the IP multicast tree; this will reduce network bandwidth usage and delivery delay, as well as the computation required at the sources and sinks. We evaluate the situations in which CBM is advantageous. The benefits of CBM depend critically upon how well filters are placed at interior nodes of the IP multicast tree and the costs depend upon those introduced by filters themselves. Further, we consider the benefits of allowing the filters to be mobile so as to respond to user mobility or changes in user interests and the corresponding costs of filter mobility. The criterion that we consider is the total network bandwidth utilization. For this criterion, we develop an optimal filter placement algorithm, as well as a heuristic that executes faster than the optimal algorithm. We evaluate the algorithms by means of simulation experiments. Our results indicate that filters can be effective in substantially reducing bandwidth. We also find filter mobility is worthwhile if there is marked large-scale user mobility. We conclude with suggestions for further work.     

Effect of exponentially graded base doping on the performance ofGaAs/AlGaAs heterojunction bipolar transistors

The authors have fabricated n-p-n GaAs/AlGaAs heterojunction bipolar transistors (HBTs) with base doping graded exponentially from 5×10¹⁹ cm^-3 at the emitter edge to 5×10¹⁸ cm^-3 at the collector edge. The built-in field due to the exponentially graded doping profile significantly reduces base transit time, despite bandgap narrowing associated with high base doping. Compared to devices with the same base thickness and uniform base doping of 1×10¹⁹ cm^-3 , the cutoff frequency is increased from 22 to 31 GHz and maximum frequency of oscillation is increased from 40 to 58 GHz. Exponentially graded base doping also results ill consistently higher common-emitter current gain than uniform base doping, even though the Gummel number is twice as high and the base resistance is reduced by 40%     

Long-wavelength infrared photoinduced switching of a resonanttunneling diode using the intersubband transition

Voltage switching induced by long-wavelength infrared light from a CO₂ laser was observed using a double-barrier resonant tunneling diode (RTD) biased in the bistable region and the intersubband transition (IT) between the quantum confined states. Possible optoelectronic and all-optical switching applications involving hysteresis are proposed and discussed     

Rotative quadrature phase-shift keying

A rotative quadrature phase-shift keying (RQPSK) modulation scheme is proposed. By rotating the QPSK signal constellation by pi /2 either clockwise or anticlockwise during a symbol duration, the conventional QPSK scheme can be modified to transmit 3 bits per symbol to achieve both power and bandwidth efficiency.<>