High-gain pseudomorphic InGaAs base ballistic hot-electron device

A high-gain ballistic hot-electron device is described. The GaAs-AlGaAs heterostructure device, with a 21-mm-thick pseudomorphic In _0.12Ga_0.88As base, had a current gain of 27 at 77 K and 41 at 4.2 K. As characteristically seen in ballistic devices, transfer into the L valley limited the maximum gain. The Γ-L valley separation in the strained In_0.12Ga_0.88As was estimated to be about 380 meV     

Simulation of the initial stages of nucleation and growth of Au/NaCl(100)

The results of a computer simulation of the initial stages of the nucleation and growth of gold on NaCl(100) are presented. A potential energy scaling Monte Carlo model employing a 50 × 50 array, mobile monomers, dimers and trimers, and gold atom vertical “roll up” was used. The parameters in the model were obtained from the work of Robinson and Robins, other published sources and/or found by calculation. Simulations of the migration of single gold adatoms over the surface permitted the determination of the diffusion coefficient as a function of the reciprocal temperature which returned the same activation energy given by the potential field, thus indicating the consistency of the model. Initial cluster densities were determined using deposition rates of R_d = 10¹⁵cm^-2s^-1 and R_d = 10¹⁴cm^-2s^-1 over the temperature range T=200–425 K. Initial cluster growth was found to occur primarily by surface phase transport and resulted in clusters that were shaped like very thin disks. Using the equations from the work of Velfe and coworkers, calculations were made to extrapolate the computer simulation data in order to permit an indirect comparison with the data of Robinson and Robins. Good agreement was achieved. Initial condensation coefficients determined over a 250 ms interval showed that α ≈ 0 at T > 425 K and α ≈ 1 at T < 325 K for a deposition rate of R_d=10¹⁵ cm^-2 s^-1.     

Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

High performance biofilm process for treating wastewater discharged from coal refining plants containing nitrogen, cyanide and thiocyanate.

Wastewater discharge from coal refining plants contains a number of biologically toxic compounds; 2000-2500 mg/l of COD of which 40% is composed of phenol, 100-400 mg/l of thiocyanate, 10-40 mg/l of cyanide, 100-250 mg/l of NH4+-N and 150-300 mg/l of total nitrogen. In order to treat this kind of high strength wastewater, we have developed a high performance biofilm process using fluidizing bio-carriers of the tube chip type. The fluidizing biofilm carriers are made of a composite of polyethylene and several inorganic materials, whose density is controlled at 0.97-0.98 g/ml. The fluidizing biofilm carriers show sound fluidization characteristics inside bioreactors. The wastewater is treated using three consecutive series reactors in oxic-anoxic-oxic arrangement. Each reactor is charged with the fluidizing biofilm carriers of 50 vol%. Furthermore, newly cultured active microorganisms for the thiocyanate biodegradation are added in the biofilm process. At total hydraulic retention time of 2.2 days, this process can achieve steady state removal efficiencies: COD, 99%; thiocyanate, 99%; NH4+-N, 99% and total nitrogen, 90%.     

Optical characteristics of waste stabilization ponds: recommendations for monitoring.

The optical character of waste stabilization ponds (WSPs) is of concern for several reasons. Algal photosynthesis, which produces oxygen for waste oxidation in WSPs, is influenced by attenuation of sunlight in ponds. Disinfection in WSPs is influenced by optical characteristics because solar UV exposure usually dominates inactivation. The optical nature of WSPs effluent also affects assimilation by receiving waters. Despite the importance of light behaviour in WSPs, few studies have been made of their optical characteristics. We discuss simple optical measures suitable for routine monitoring of WSPs (including at sites remote from laboratories): optical density of filtrates - an index of dissolved coloured organic (humic) matter, visual clarity - to provide an estimate of the beam attenuation coefficient (a fundamental quantity needed for optical modelling) colour (hue) - as an indicator of general WSP 'condition' and irradiance attenuation quantifying depth of light penetration. The value of optical characterisation of WSPs is illustrated with reference to optical data for WSPs in NZ (including high-rate algal ponds) treating dairy cattle wastewater versus domestic sewage. We encourage increased research on optical characteristics of WSPs and the incorporation of optical measures in monitoring and modelling of WSP performance.     

An integrated system to remote monitor and control anaerobic wastewater treatment plants through the internet.

The TELEMAC project brings new methodologies from the Information and Science Technologies field to the world of water treatment. TELEMAC offers an advanced remote management system which adapts to most of the anaerobic wastewater treatment plants that do not benefit from a local expert in wastewater treatment. The TELEMAC system takes advantage of new sensors to better monitor the process dynamics and to run automatic controllers that stabilise the treatment plant, meet the depollution requirements and provide a biogas quality suitable for cogeneration. If the automatic system detects a failure which cannot be solved automatically or locally by a technician, then an expert from the TELEMAC Control Centre is contacted via the internet and manages the problem.     

Computerized conferencing for knowledge acquisition from multiple experts

The increasing complecity of many expert system application areas calls for the integration of the knowledge of multiple experts. The use of multiple experts introduces some interesting new problems during the process of knowledge acquisition. The problems are further complicated when the experts are geographically dispersed or unavailable for face-to-face interactions.

This article discusses the motivations for acquiring the knowledge of multiple experts, the problems related to knowledge acquisition, new issues that arise whens multiple experts interact, solutions that can be brought to bear in building multiple expert systems (particularly when experts are geographically dispersed), and new tools for knowledge engineers to use when dealing with multiple experts.     

The application of SSADM to modelling the logical structure of proteins.

A logical design that describes the overall structure of proteins, together with a more detailed design describing secondary and some supersecondary structures, has been constructed using the computer-aided software engineering (CASE) tool, Auto-mate. Auto-mate embodies the philosophy of the Structured Systems Analysis and Design Method (SSADM) which enables the logical design of computer systems. Our design will facilitate the building of large information systems, such as databases and knowledgebases in the field of protein structure, by the derivation of system requirements from our logical model prior to producing the final physical system. In addition, the study has highlighted the ease of employing SSADM as a formalism in which to conduct the transferral of concepts from an expert into a design for a knowledge-based system that can be implemented on a computer (the knowledge-engineering exercise). It has been demonstrated how SSADM techniques may be extended for the purpose of modelling the constituent Prolog rules. This facilitates the integration of the logical system design model with the derived knowledge-based system.     

Sensory analysis of polystyrene packaging material taint in cocoa powder for drinks and chocolate flakes

Polystyrene packaging material taint was sensorily evaluated in cocoa powder for drinks and chocolate flakes using short-cut signal detection measures on differences between control and test samples and on recognition of styrene. No differences were observed in cocoa powder for drinks and plain chocolate flakes treated with 0.5 dm2 polystyrene of 1 mm thickness. However, differences were detected in milk chocolate flakes and plain chocolate flakes, which were in contact with a larger area or thicker polystyrene packaging material. The latter results were confirmed by the styrene recognition test, so polystyrene is a potential source of off-flavour for chocolate products. The amount of residual styrene in the polystyrene used was about 320 ppm, while the amounts of styrene ranged from 7 to 132 ppb in cocoa drinks and from 414 to 1447 ppb in chocolate flakes.     

Current and future water issues in the Oldman River Basin of Alberta, Canada.

Long-term trends in alpine and prairie snow pack accumulation and melt are affecting streamflow within the Oldman River Basin in southern Alberta, Canada. Unchecked rural and urban development also has contributed to changes in water quality, including enhanced microbial populations and increased waterborne pathogen occurrence. In this study we look at changing environment within the Oldman River Basin and its impact on water quality and quantity. The cumulative effects include a decline in net water supplies, and declining quality resulting in increased risk of disease. Our data indicates that decreases in the rate of flow of water can result in sedimentation of bacterial contaminants within the water column. Water for ecosystems, urban consumption, recreation and distribution through irrigation is often drawn from waterholding facilities such as dams and weirs, and concern must be expressed over the potential for contaminate build-up and disproportionate potential of these structures to pose a risk to human and animal health. With disruption of natural flow rates for water resulting from environmental change such as global warming and/or human intervention, increased attention needs to be paid to use of best management practices to protect source water supplies.