光纤光栅感温火灾探测报警系统在原油罐区的应用

通过对现有罐区火灾自动报警技术的认真考察、对比,在石西集中处理站原油罐区安装了光纤光栅感温火灾探测报警系统.该报警系统的传感信号是光的波长变化,传感器及其探测系统是靠光缆连接而进入被测现场,它具有高安全性、高可靠性、高绝缘性、高抗电磁干扰性、防潮耐蚀、寿命长等其他传统火灾探测报警系统无法比拟的优越性能.阐述了其系统构成和运行效果.该系统在石西集中处理站运用效果良好.     

乳化钻井液条件下高温高压气井气体扩散研究

高温高压下甲烷在油里的溶解度大，水包油乳化钻井液中存在油相，钻井作业中钻井液静置期间如起下钻、工具故障抢修等时间过长，储层中的甲烷气体会扩散到井眼里。在钻高含硫化氢及二氧化碳气井时，高温高压条件下天然气更有可能到达与油完全互溶的状态。文章将储层内的水平段井眼的气体扩散区域划分为4个区，外滤饼区、内滤饼区、滤液滞留区、滤液未污染区，根据外滤饼区、内滤饼区、滤液滞留区不同计算参数条件，计算预测了在使用水包油乳化钻井液情况下，储层中天然气通过扩散穿过3个区后，进入储层内井眼段环空导致的环空含气质量浓度变化，对环空内含气质量浓度随扩散时间、含油浓度因素的变化进行了定量计算。用伽略金有限元方法求解，计算表明，气体扩散量随钻井液静置时间延长而增加，水基钻井液加入油后与不加油的钻井液相比增大了气体扩散量。     

相关条件下基于N-P准则的分布式检测理论研究

本文针对并行网络、二元局部判决的情况,研究了在相关条件下基于N-P准则的分布式检测融合算法,给出了在联合概率密度已知和未知两种情况下的最优融合规则的理论推导及相应的解决方案,并在实验仿真的基础上,得到了部分有益的结论。     

一种的四进制CPM调制器的设计与FPGA实现

设计并实现了一种基于FPGA的四进制连续相位调制器（PCM）。该调制器的基带调制模块通过查表法实现，复杂度较低。仿真结果验证了设计的正确性。     

动感像素全息母版图案的设计制作研究

本文介绍了一种新颖的数码像素全息高速拍摄装置来实现全息母版的制作。提出和介绍了运用Photoshop软件一些特殊的图像处理功能设计制作动感像素全息图的方法,并结合多种防伪技术,使产生的图案具有不可仿制的图形畸变特点,并列举了设计实例。     

干涉型激光直写技术用于光盘防伪

利用作者研制的干涉型激光直写系统，阐述了干涉型激光直写设计OVD的方法，防伪特征，介绍了应用于光盘防伪的OVD技术和应用前景，给出了实验结果。     

Pack cementation process for the formation of refractory metal modified aluminide coatings on nickel-base superalloys

The vapour phase compositions of a series of pack powder mixtures containing elemental Al and Hf or W powders as depositing sources and CrCl₃·6H₂O or AlF₃or CrF₃as activators were analysed in an attempt to further develop the pack cementation process to codeposit Al and Hf or W to form diffusion coatings on nickel base superalloys. The results suggested that Al could be codeposited with Hf, but not with W, from the vapour phase. Compared with both AlF₃and CrF₃, CrCl₃·6H₂O has been shown to be a more suitable activator for codepositing Al with Hf. The optimum coating temperature was identified to be in the range of 1050°C to 1150°C. Based on the thermochemical analysis, a series of coating deposition studies were undertaken, which confirmed that codeposition of Al and Hf could be achieved at a deposition temperature of 1100°C in the CrCl₃·6H₂O activated packs containing elemental Al and Hf powders. The coating obtained had a multilayer structure consisting of a Ni₇Hf₆Al₁₆top layer and a NiAl layer underneath, followed by a diffusion zone, which revealed that the coating was formed by the outward Ni diffusion. It is suggested that the compositions suitable for codeposition of Al and Hf could be effectively identified by comparing the vapour pressures of HfCl₄and HfCl₃with that of AlCl in the packs activated by chloride salts. It has also been experimentally demonstrated that, although W could not be deposited from the vapour phase, a high volume of fine W particles can be entrapped into the outer NiAl coating layer formed by the outward Ni diffusion using a modified pack configuration. This leads to the formation of a composite coating layer with W particles evenly distributed in a matrix of NiAl. It is suggested that this modified pack process could be similarly applied to develop nickel aluminide coatings containing other refractory metals that may not be codeposited with Al from the vapour phase.     

高酸原油脱酸工艺技术研究

介绍了一种原油脱酸工艺方法。研究了温度、时间对高酸原油脱酸的影响,脱酸温度大于 260℃,脱酸反应较快。分析了高酸原油脱酸前后馏分酸值的变化,脱酸反应对130℃以上各馏分酸值降低都较多,180℃以上馏分脱酸率在80％以上。     

Breaking a remote user authentication scheme for multi-server architecture

Lin et al., (2003) proposed a remote user authentication scheme for multi-server architecture. In this paper, we breaks this scheme by giving an attack. Our attack allows an adversary to impersonate any user in the system, as long as a single authentication message of that user is observed.     

TEM Studies of High Temperature Corrosion Behaviour of TiAl Intermetallics with Surface Modifications

The oxidation/sulphidation behaviour of a Ti‐46.7Al‐1.9W‐0.5Si alloy with a TiAl₃ diffusion coating was studied in an environment of H₂/H₂S/H₂O at 850^oC. The kinetic results demonstrate that the TiAl₃ coating significantly increased the high temperature corrosion resistance of Ti‐46.7Al‐1.9W‐0.5Si. The SEM, EDX, XRD and TEM analysis reveals that the formation of an Al₂O₃ scale on the surface of the TiAl₃‐coated sample was responsible for the enhancement of the corroison resistance. The Ti‐46.7Al‐1.9W‐0.5Si alloy was also modified by Nb ion implantation. The Nb ion implanted and as received sampels were subjected to cyclic oxidation in an open air at 800^oC. The Nb ion implantation not only increased the oxidation resistance but also substantially improved the adhesion of scale to the substrate.