Microhardness measurements and the Hall-Petch relationship in an AlMg alloy with submicrometer grain size

An Al-3% Mg solid solution alloy was subjected to intense plastic deformation, using either equal-channel angular (ECA) pressing or torsion straining, to produce grain sizes in the submicrometer range. Static annealing at elevated temperatures led to grain growth and average grain sizes of up to > 100 μm. As-fabricated and statically annealed specimens were used to determine the variation in microhardness with grain size, and results confirm that the Hall-Petch relationship persists down to at least the finest grain size examined experimentally (∼90 nm). The results provide no evidence to support the claims of a negative Hall-Petch slope when the average grain size is very small, but there is evidence of a decrease in the slope of the Hall-Petch plot at the very finest grain sizes (< 150 nm); this is attributed to the increased participation of mobile extrinsic dislocations in the boundary regions when taking the hardness measurements.     

c-axis oriented ZnO formed in a rotating magnetic field with various rotation speeds

A rotating magnetic field was used to fabricate c-axis oriented zinc oxide. The influence of rotating speed on orientation structure was also examined. The aligned axes had the largest diamagnetic susceptibility, which axis was difficult to align with a static magnetic field. In c-axis oriented ZnO, the degree of orientation (Lotgering factor) in the green compact ranged from 0.2 to 0.5 along c-axis. The Lotgering factor increased with rotating speed. For all samples with the rotating magnetic field, the degrees of orientation increased up to above 0.9 after sintering at 1573 K.     

Comparative study of the physicochemical and palynological characteristics of honey from Melipona subnitida and Apis mellifera

Twenty‐four samples of Apis mellifera honey and twenty‐four samples of Melipona subnitida (Jandaira) honey were collected in the northeast of Brazil. Moisture, hydroxymethylfurfural, free acidity, insoluble solids in water, diastase activity, ashes, electrical conductivity, proteins, lipids, total carbohydrates, energy and sugars were the parameters analysed. The efficiency of the qualitative tests (Fiehe's test, Lugol's reaction, Lund's reaction) was tested. Pollen types and the corresponding plant species were identified in all samples (3 in Apis and 1 in Melipona). Apis mellifera honey samples demonstrated parameters in accordance with the Brazilian Legislation, while the Melipona subnitida honey samples displayed moisture (24.80%) and diastase activity (null) in discordance with the established by the regulation for Apis mellifera honeys. Apis honey samples presented higher values of electric conductivity (284.00 μS cm^?1) than the obtained from the Jandaira honey samples (102.77 μS cm^?1) as well as a darker colour (26.67 mmPfund) when compared with Jandaira honey (7.00 mmPfund). The concentration of the glucose, fructose and sucrose was higher in the Apis honeys than in the Jandaira honey. The characteristics of the two types of honey were very different, highlighting the need of developing specific legislation for stingless bees' honey.     

Evaluation of TEM samples of an Mg-Al alloy prepared using FIB milling at the operating voltages of 10 kV and 40 kV

Transmission electron microscopy (TEM) samples of an Mg-Al alloy has been prepared using a Ga-focused ion beam (FIB) milling at two different operating voltages of 10 kV and 40 kV to investigate the influence of the FIB energy on the sample quality. The fine structures of the samples have been studied using a high resolution TEM, and the concentration of the implanted Ga was analysed using an energy dispersive X-ray (EDX) analysis. The result of the TEM observation revealed that point defects were introduced to the sample finally milled at 40 kV but not at 10 kV. However, crystal lattice images and electron diffraction patterns were clearly observed on both the samples. The typical influence of the FIB energy was indicated in the elemental analysis. The relative Ga concentration in the thin sample finally milled at 10 kV was 1.0-2.0 at% that is less than half of 4.0-6.0 at% of the Ga concentration in the sample finally milled at 40 kV. A comparison between the experimental results of the Ga concentration measurement with simulation was also discussed.     

TEM,XPS and SIMS Analyzes on Grain Boundary of Lanthanum Chromites

The morphological characteristics, chromium valence state, and cation transport in the vicinity of grain boundary in La_1-xCa_xCrO₃ were investigated by using TEM/EDS, XPS and SIMS techniques. The width of grain boundary was around 1 nm where anomalous enrichment of calcium was observed. Higher valence state of chromium such as Cr⁶⁺(d⁰) was detected in the grain boundaries whereas Cr³⁺(d³) and Cr⁴⁺(d²) were dominant in the bulk. Very fast interdiffusion of alkaline earths was observed in the Sr²⁺-La_0.75Ca_0.25CrO₃ system. All observed phenomena were correlated by assuming the A-site vacancy which may be induced by the formation of Cr⁶⁺ at grain boundaries.     

Strengthening and hydrogen embrittlement of ultrafine-grained Fe–0.01 mass% C alloy processed by high-pressure torsion

This study was conducted to elucidate the effects of annealing and hydrogenation on the tensile properties of an Fe–0.01 mass% C alloy processed by high-pressure torsion (HPT). By HPT processing, the tensile strength was increased to ∼1500 MPa through grain refinement. Low-temperature annealing further strengthened the HPT-processed specimen because of a simultaneous effect of carbide precipitation and grain refinement. Reduction in the dislocation density and the fraction of low-angle grain boundaries through warm-temperature annealing led to a decrease in hydrogen uptake when the specimens were exposed to high-pressure gaseous hydrogen, and they became less sensitive to hydrogen embrittlement (HE).     

Direct observation of internal structure in spray-dried yttria-doped zirconia granule

Spray-dried yttria-doped zirconia granules were made transparent by immersion in a liquid and the internal structure was characterized using an optical microscope. This unique technique was found to be applicable for this system by using an immersion liquid with appropriate refractive index, and it enabled observation of the internal structure to be made over the entire volume of granules, in clear contrast to conventional SEM observation. Distinct features, which were considered to be agglomerates, were found in the granules. This was supported by SEM observation.     

Phase diagram calculations of ZrO2-based ceramics with an emphasis on the reduction/oxidation equilibria of cerium ions in the ZrO2-YO1.5-CeO2-CeO1.5 system

Phase diagram calculations that were made previously for the ZrO₂-MO _m/2 (m = 2, 3, 4) systems and for the ZrO₂-YO_1.5-MO _m/2 (M = transition metals) systems have been extended to the ZrO₂-YO_1.5-CeO₂(-CeO_1.5) system to make an attempt to explain (1) thermogravimetric (TG) results as a function of oxygen potential, (2) electronic conductivity as a function of oxygen potential, and (3) a miscibility gap observed in air. The interaction parameters for the CeO₂-CeO_1.5-YO_1.5 system were obtained from the reported oxygen nonstoichiometry in CeO_2−x and rate earth doped ceria, (Ce,RE)O_2−δ . The interaction parameters for the ZrO₂-CeO₂ subsystem were obtained so as to reproduce the observed miscibility gap at 1273 K. Those thermodynamic properties can reproduce consistently the experimental behaviors of the electronic conductivity and the TG results in the (Zr_1−x Ce _x )_0.8Y_0.2O_1.9 solid solutions; these indicate the enhancement of reduction of CeO₂.