Deformation and fracture of glass bead/ CTBN-rubber/epoxy composites

Carboxyl-terminated butadiene-acrylonitrile-rubber decreases modulus and yield stress of the studied epoxy but increases fracture toughness. The addition of glass bead compensates for the loss in modulus but has little effect on yield stress. However, it significantly contributes to the fracture toughness by providing additional mechanisms for toughening of both the unmodified and rubber-modified epoxy. For the toughened epoxies studied, fracture surfaces gave only limited information on fracture mechanisms since significant energy absorption also occurs in the material below the fracture surface. Suggestions for suitable material compositions for fiber composite matrices are given.     

Systematic characterization of Cl2 reactive ion etchingfor improved ohmics in AlGaN/GaN HEMTs

Pre-metal-deposition reactive ion etching (RIE) was performed on an Al_0.3Ga_0.7N/AlN/GaN heterostructure in order to improve the metal-to-semiconductor contact resistance. An optimum AlGaN thickness for minimizing contact resistance was determined. An initial decrease in contact resistance with etching time was explained in terms of removal of an oxide surface layer and/or by an increase in tunnelling current with the decrease of the AlGaN thickness. The presence of a dissimilar surface layer was confirmed by an initial nonuniform etch depth rate. An increase in contact resistance for deeper etches was experienced. The increase was related to depletion of the two-dimensional (2-D) electron gas (2-DEG) under the ohmics. Etch depths were measured by atomic force microscopy (AFM). The contact resistance decreased from about 0.45 Ωmm for unetched ohmics to a minimum of 0.27 Ωmm for 70 Å etched ohmics. The initial thickness of the AlGaN layer was 250 Å. The decrease in contact resistance, without excessive complications on device processing, supports RIE etching as a viable solution to improve ohmic contact resistance in AlGaN/GaN HEMTs     

New insights in polarity-dependent oxide breakdown for ultrathin gate oxide

In this work, a quantitative analysis is applied to resolve the newly reported polarity-dependent charge-to-breakdown (Q/sub BD/) data from thick oxides of 6.8 nm down to ultrathin oxides of 1.9 nm. Three independent sets of Q/sub BD/ data, i.e., n/sup +/poly/NFET stressed under inversion and accumulation, and p/sup +/ poly/PFET under accumulation are carefully investigated. The Q/sub BD/ degradation observed for p-type anodes, either poly-Si or Si-substrate, can be nicely understood with the framework of maximum energy released by injected electrons. Thus, this work provides a universal and quantitative account for a variety of experimental observations in the time-to-breakdown (T/sub BD/) and Q/sub BD/ polarity-dependence of oxide breakdown.     

A robust adaptive pole‐placement controller without strictly positive real condition

This paper considers the adaptive pole‐placement control problem for system (1) with unmodelled dynamics η_n dominated by a small constant ε multiplied by a quantity independent of ε but tending to infinity as the past input, output, and noise grow. Using bounded external excitation and randomly varying truncation techniques, we give a design method of adaptive pole‐placement controller. It is shown that the closed‐loop system is globally stable, the estimation error for the parameter contained in the modelled part is of order ε, and the closed‐loop system under the adaptive pole‐placement control law is suboptimal in the sense of $$\mathop{\lim\sup}\limits_{{n\to\infty }}{1\over n}\mathop{\sum}\limits_{i=0}^n{\left({A^{*}(z)y_{n}‐L(z)C(z)w_{n}‐B(z)R(z)y_{n}^{*}}\right)^{2}{\leq}O({\varepsilon}^{2})+\gamma^{2}\mathop{\sum}\limits_{j=1}^q{b_{j}^{2}}}$$\nopagenumbers\end while the SPR condition used usually in other papers is replaced by a stability condition. Copyright © 2001 John Wiley & Sons, Ltd.     

A Distributed State Estimator Utilizing Synchronized Phasor Measurements

With the creation of balancing authorities by the North American Reliability Council that span large portions of the North American interconnection, and stringent requirements for real time monitoring of power system evolution, faster and more accurate state estimation algorithms that can efficiently handle systems of very large sizes are needed in the present environment. This paper presents a distributed state estimation algorithm suitable for large-scale power systems. Synchronized phasor measurements are applied to aggregate the voltage phase angles of each decomposed subsystem in the distributed state estimation solution. The aggregated state estimation solution is obtained from the distributed solution using a sensitivity analysis based update at chosen boundary buses. Placement of synchronized phasor measurements in the decomposed subsystems is also investigated in this paper. Test results on the IEEE 118-bus test bed are provided     

Boosting nitrification by membrane-attached biofilm.

Nitrification is a key step for reliable biological nitrogen removal. In order to enhance nitrification in the activated sludge (AS) process, membrane-attached biofilm (MAB) was incorporated in a conventional activated sludge tank. Simultaneous organic carbon removal and nitrification of the MAB incorporated activated sludge (AS + MAB) process was investigated with continuous wastewater treatment. The effluent TOC concentration of AS and the AS + MAB processes were about 6.3 mg/L and 7.9 mg/L, respectively. The TOC removal efficiency of both AS and AS + MAB were above 95% during the wastewater treatment, indicating excellent organic carbon removal performance in both processes. Little nitrification occurred in the AS process. On the contrary, successful nitrification was obtained with the AS + MAB process with nitrification efficiency of about 90%. The volumetric and surface nitrification rates were about 0.14 g/Ld and 6.5 g/m2d, respectively. The results clearly demonstrated that nitrification in the conventional AS process was boosted by MAB. Furthermore, the microfaunal population in the AS + MAB process was different from that in the AS process. The high concentration of rotifers in the AS + MAB process was expected to decrease the generation of excess sludge in the process.     

Preparation of flexible polyhedral particles via concentrated emulsion templating polymerization

This paper presents recent efforts on the preparation of flexible polyhedral particles via concentrated emulsion templating polymerization in which the hydrophilic monomer (acrylamide) and hydrophobic monomer (butyl acrylate) are polymerized simultaneously in the continuous and dispersed phase, respectively. Such templating polymerization has been enhanced in our systems owing to the introduction of acrylamide monomer and their higher polymerization rate in continuous phase as compared with butyl acrylate in dispersed phase. Diffusion between the different phases was also inhibited. Furthermore, the stability of the concentrated emulsion and the molecular weight of the produced poly(butyl acrylate) were found to be significantly affected by the amount of redox initiator. The morphology of the particles could be controlled by varying the volume fraction of the dispersed phase and the polyhedral particles were achieved at higher volume fraction. Copyright © 2005 Society of Chemical Industry