高质量的一级光栅1．55μmDFB激光器

本文详细叙述了ＤＦＢ激光器的设计要点和新的工艺。采用一级全息光栅和二步液相外延法批量研制出高稳定单纵模工作的１．５５μｍ分布反馈激光器（ＤＦＢ—ＬＤ）。外延片成品率＞４０％。器件特性：２５℃时阈值电流２０ｍＡ，单面光功率＞１０ｍｗ，主边模抑制比ＳＭＳＲ达４３ｄＢ（λ／４相移光栅），谱线宽度△ν－２０ｄＢ＝０．３ｎｍ，调制速率＞１．８ＧＨｚ。可靠性测试显示：高温监测光谱稳定，２５°Ｃ时阈值退化率△Ｉｔｈ／ｔ＜０．３ｍＡ／ｋｈ，对应器件预估寿命将超过１０万ｈ。     

Comparisons of PWM and one-cycle control for power amplifier with multilevel converter

Based on the concepts of cascade multilevel converters and one-cycle technique, comparisons are conducted to characterize the distortion of the pulsewidth modulation (PWM) and one-cycle control methods that were applied to converters. Simulation results for the different control schemes are obtained in PSIM software initially to see the effect of one-cycle control different from that of PWM control. Through the comparisons, the advantages and disadvantages are identified for each method. The one-cycle scheme is better than PWM control in reducing undesirable harmonics and tracing dynamic waveforms. Simulation and experimental results are also provided to verify the conclusions.     

Development of a numerical comparator for protective relaying: PartII

This paper describes the testing of a new power system numerical relaying concept. The new technique is applied to distance relaying to offer improved reliability and security of the relay, and improve the speed of relay operation. To validate the algorithm's performance, the scheme was analyzed under a variety of test conditions and compared with conventional relay concepts. This paper presents the results of the testing and shows that the new relaying scheme operated with a high level of security and dependability for all of the test cases. The tests show improvements that the new scheme can offer in comparison to the conventional schemes     

土钉支护结构水平位移安全监控模型研究

国内现行规范、标准是以极限变形值作为土钉支护结构水平位移安全监测报警值 ,但没有反映工程进度影响 ,不便指导工程实践。提出“过程控制”概念 ,以反正切函数为基本形式 ,基于历史经验建立“安全时程曲线”控制模型 ,要求施工过程中实测水平位移始终处在“安全时程曲线”之下 ,以确保最终变形在某一适当的阈值之内 ,已有实测结果可以为施工方案调整提供依据。通过实际案例 ,检验模型的可行性 ,表明过程控制模型较极限变形策略更具可操作性     

Automation model of sewerage rehabilitation planning.

The major steps of sewerage rehabilitation include inspection of sewerage, assessment of structural conditions, computation of structural condition grades, and determination of rehabilitation methods and materials. Conventionally, sewerage rehabilitation planning relies on experts with professional background that is tedious and time-consuming. This paper proposes an automation model of planning optimal sewerage rehabilitation strategies for the sewer system by integrating image process, clustering technology, optimization, and visualization display. Firstly, image processing techniques, such as wavelet transformation and co-occurrence features extraction, were employed to extract various characteristics of structural failures from CCTV inspection images. Secondly, a classification neural network was established to automatically interpret the structural conditions by comparing the extracted features with the typical failures in a databank. Then, to achieve optimal rehabilitation efficiency, a genetic algorithm was used to determine appropriate rehabilitation methods and substitution materials for the pipe sections with a risk of mal-function and even collapse. Finally, the result from the automation model can be visualized in a geographic information system in which essential information of the sewer system and sewerage rehabilitation plans are graphically displayed. For demonstration, the automation model of optimal sewerage rehabilitation planning was applied to a sewer system in east Taichung, Chinese Taiwan.     

27keV Ar~+斜入射时的Cu-Au合金溅射实验角分布

用27keV Ar~+分别在垂直和倾斜入射情况下,轰击了Cu-Au(30wt％)合金样品,测量了Cu和Au原子的溅射角分布。角分布是用卢瑟福背散射(RBS)技术分析Al捕获膜上的Cu-Au沉积成分而定量得到的。结果表明:(1)在Ar~+倾斜(θ=40°)入射时,Cu原子择优发射,且程度比垂直入射(θ_r=O°)时增强:(2)倾斜入射时,Cu原子的角分布显示出在接近于样品表面法线方向的发射角范围内(θ<45°),发射机率比垂直入射时减小。