One-step molten salt carbonization of tobacco stem for capacitive carbon

Journal of Porous Materials - High-performance carbon materials for supercapacitors were prepared by a one-step molten salt carbonization of tobacco stem in molten carbonate. Physicochemical...     

含多端口能量路由器的多能互补系统故障保护功能测试研究

针对某区域用电负荷存在严重的季节性过载现象,以及可再生能源存在功率波动大、稳定性较差的问题,研制了多能(含水电、光伏、储能)、多端口的能量路由器装置及其能量管理系统.综合考虑当地多场景运行,解决了季节性过载问题,实现了能量的合理配置与利用.首先,对比分析选定能量路由器各端口变换器的拓扑结构;然后,对多场景下的工作模式进行介绍;最后,对含能量路由器的多能互补系统进行故障保护功能测试.测试结果表明,该系统具有较好的故障保护功能,有效实现了不同场景下的工作模式切换,直流母线电压稳定以及上层功率指令跟踪等功能,解决了当地用电负荷季节性过载和可再生能源功率波动较大的问题.     

关节式电分相电磁暂态过程研究

关节式电分相是电气化铁路牵引供电系统较为薄弱的环节,电力机车在通过关节式电分相时经常会产生过电压现象,过电压可能会造成机车放电间隙击穿、牵引所馈线保护跳闸,严重影响铁路的安全运营.从实测结果来看,机车在过渡区和中性区行驶时过电压会持续存在一段时间,与以往对关节式电分相产生过电压的研究作对比,分析造成电磁暂态过程以及过电压延续的原因可能是机车的移动.在MATLAB/Simulink软件上建立了机车过关节式电分相的仿真模型,用多个离散过程来近似模拟机车过电分相的连续过程,最后与实测波形对比,验证等效模型是有效的.     

不同活化剂对石油焦基活性炭孔结构的影响

以石油焦为原料 ,Na OH,KOH和 Na2 CO3 为活化剂制备活性炭 ,采用氮气吸附考察了不同活化剂对活性炭的比表面积、中孔和微孔孔径分布、孔容积及平均孔径等孔结构的影响 .结果表明 :KOH活化制备的活性炭包含 1 nm的微孔和 4nm的中孔 ,总孔容 0 .648cm3 /g,比表面积大 ;Na OH制备的活性炭以 1 nm的微孔为主 ,占总孔容 ( 0 .1 65 cm3 /g)的 98% ,平均孔径 1 .83nm;Na2 CO3 制备的活性炭以 4nm的中孔为主 ,占总孔容 ( 0 .1 43cm3 /g)的 68.5 % ,平均孔径 3.42 nm,比表面积小 .3种样品的孔径都呈现出多峰分布特征 .KOH和 Na2 CO3 活化制备的活性炭的 N2 吸附脱附曲线属于 型 ,Na OH活化制备的活性炭吸附脱附曲线属于 型 .     

Properties of poly(n‐butyl methacrylate) prepared by reverse atom transfer radical polymerization in an aqueous dispersed system

Reverse atom transfer radical polymerization (ATRP) of n‐butyl methacrylate (BMA) in waterborne media using Cu(II) complexes with azo initiators (i.e., reverse ATRP) was conducted. The influence of several factors, such as surfactant, catalyst, and reaction time, on the stability of the emulsion, the particle size, the morphology of the emulsion particles, and the control of the polymerization was investigated. The results showed great differences between ATRP and conventional emulsion polymerization, especially the nucleation mechanism and the kinetics. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1542–1547, 2003     

Electron Emission from Barium Strontium Titanate Ceramics

This paper focuses on understanding the influence of materials' properties on the ferroelectric electron emission. Ferroelectric ( x =1.0 and 0.8) and paraelectric ( x =0.67 and 0.5) compositions of barium strontium titanate (Ba _x Sr_{(1− x )}TiO₃) system were chosen for study based on their different ferroelectric and dielectric properties. Similar emission current waveforms were obtained from four compositions with negative triggering voltage applied to the rear electrode of the samples. It was difficult to explain the experimental results using the spontaneous polarization-switching model. The mechanism of electron emission from Ba _x Sr_{(1− x )}TiO₃ ceramics was ascertained to surface plasma emission.     

PVC助剂的新进展

介绍了近年来聚氯乙烯助剂的研制、开发的现状和趋势。     

Toughening by Metallic Lamina in Nickel/Alumina Composites

Tape casting and hot-pressing were used to produce metal/ alumina laminate composites. The mechanical behavior of these laminates was characterized. The strength and toughness of the laminates were greatly improved in comparison to that of monolithic alumina. Indentation strength values of the laminates remained approximately constant for indent loads between 10 and 100 N. Thus, this type of laminate appears to be a good candidate for damage-tolerant composite material design.     

Transformation of β-Ni(OH)2 to NiO nano-sheets via surface nanocrystalline zirconia coating: Shape and size retention

Shape and size of the synthesized NiO nano-sheets were retained during transformation of sheet-like β-Ni(OH)₂ to NiO at elevated temperatures via nano-sized zirconia coating on the surface of β-Ni(OH)₂. The average grain size was 6.42 nm after 600 °C treatment and slightly increased to 10 nm after 1000 °C treatment, showing effective sintering retardation between NiO nano-sheets. The excellent thermal stability revealed potential application at elevated temperatures, especially for high temperature catalysts and solid-state electrochemical devices.