Design of photonic crystal fibers for dispersion-related applications

A general procedure for design of photonic crystal fibers (PCFs) with desirable dispersion properties is presented. The design model is based on the combination of a rigorous vector mode solver and a scaling transformation for the dispersion properties of the PCFs. In comparison with the conventional design method, the new design procedure is more efficient and can be readily automated for the purpose of design optimization. Several applications of the design procedure, e.g., the design optimization for dispersion shifted fibers, dispersion flattened fibers, and dispersion compensation fibers, are demonstrated and discussed.     

Mutual coupling of two collocated orthogonally oriented circular thin-wire loops

Coupling between two collocated orthogonal circular thin-wire loops is analyzed in this paper. Two coupled integral equations for the loop currents are derived and their solution in general form is found in terms of Fourier series. An analytical expression for currents induced through the mutual coupling is obtained for the case when all loop current harmonics higher than first can be ignored. It is found that strong coupling can exist for all loop current harmonics, except for the fundamental. It is also found that coupling for orthogonal collocated loop antennas depends on the relative locations of the loop terminals.     

Hermetic Packaging Using Eutectic SnPb Solder and Cr/Ni/Cu Metallurgy Layer

We have developed an easy, low-cost, and low-temperature optoelectronic hermetic packaging technology utilizing the eutectic SnPb solder and the Cr/Ni/Cu bonding pad. Bonding characteristics of the design were investigated in three different setups: silicon-silicon, silicon-glass, and glass-glass samples. Hermeticity was achieved at 200 degC without flux for all samples during the final bonding process. The bonding pads did not dewet during or after the reflow process. By utilizing the eutectic SnPb solder, the self-alignment process can be achieved. Because the bonding process was conducted through visual alignment, original misalignment was estimated to be more than 100 mum. The surface tension of melting solder during the reflow process allowed the samples to self-align and obtain a misalignment of less than 20 mum after solidification, which was 4% of the entire solder width. The bonding strength of the three setups ranged from 3 to 10 MPa. Among the three setups, glass-glass samples appear to have the strongest bonding strength. This low-temperature and cost-effective soldering process has demonstrated its feasibility and potential utilization in optoelectronic packaging     

Measurement of gain spectrum for Fabry-Perot semiconductor lasers by the Fourier transform method with a deconvolution process

To improve the accuracy of measured gain spectra, which is usually limited by the resolution of the optical spectrum analyzer (OSA), a deconvolution process based on the measured spectrum of a narrow linewidth semiconductor laser is applied in the Fourier transform method. The numerical simulation shows that practical gain spectra can be resumed by the Fourier transform method with the deconvolution process. Taking the OSA resolution to be 0.06, 0.1, and 0.2 nm, the gain-reflectivity product spectra with the difference of about 2% are obtained for a 1550-nm semiconductor laser with the cavity length of 720 /spl mu/m. The spectra obtained by the Fourier transform method without the deconvolution process and the Hakki-Paoli method are presented and compared. The simulation also shows that the Fourier transform method has less sensitivity to noise than the Hakki-Paoli method.     

Electromagnetic coupling effects on the cavity measurement of antenna efficiency

Electromagnetic coupling effects on the antenna in a conducting cavity are studied theoretically and experimentally. It is observed in experiments that at the resonant frequencies of the cavity, the input resistance of the antenna attains values two or three orders of magnitude higher than that at frequencies away from resonance. It is shown via theoretical analysis that the input resistance of the antenna measured at the resonant frequencies of the cavity is not merely the loss resistance desired in computing the antenna efficiency, but is actually the sum of the loss resistance of the antenna and the coupling resistance between the antenna and cavity. This coupling effect is demonstrated quantitatively by numerical computations for dipole and monopole antennas. The computational results for the input resistance are in agreement with the measured data. A method is proposed to avoid the cavity-antenna antiresonance in the measurement.     

转动玻璃圆筒激光器

本文介绍了转动玻璃圆筒激光器的设计及实验结果,得到了脉冲能量为13J,重复频率为15Hz的激光输出。电光转换效率为2.2％,斜效率为3.4％。     

Postbuckling analysis of plates on an elastic foundation by the boundary element method

The postbuckling behavior of plates on an elastic foundation is studied by using the boundary element method (BEM). A new fundamental solution of lateral deflection is derived through the resolution theory of a differential operator, and a set of boundary element formulae in incremental form is presented. By using these formulae, the BEM solution procedure becomes relatively simple. The results of a number of numerical examples are compared with existing solutions and good agreement is observed. It shows that the proposed method is effective for solving the postbuckling problems of plates with arbitrary shape and various boundary conditions.     

加固改造中的结构承重体系转换

从加固改造工程的实践出发 ,探讨了混合结构向框架结构体系转换的方法和构造措施 ,为实际工程提供了新的技术思路     

住宅设计的几个消防问题

对住宅消防设计中若干规范交叉问题进行了分析 ,提出几个有待解决的问题。     

Experimentally Verified Mn–Zn Ferrites' Intrinsic Complex Permittivity and Permeability Tracing Technique Using Two Ferrite Capacitors

After setting up a mathematical model for rectangular-shaped Mn-Zn ferrite capacitors, this paper investigates dimensional effects on the intrinsic complex permittivity and the measured apparent complex permittivity of Mn-Zn ferrite blocks. The simple block structure of the samples guarantees their easy and precise preparation. Above a few hundred kilohertz, dimensional effects make the measured apparent complex permittivity deviate from its intrinsic value. This paper uses a Newton-Raphson based method to trace the intrinsic complex permittivity and permeability from the measured impedances of two rectangular-shaped Mn-Zn ferrite capacitors in the frequency range from a few hundred kilohertz to 40 MHz. From the traced intrinsic complex permittivity and permeability, the apparent complex permittivity of a third sample with different dimensions is then calculated theoretically. The papers also presents results of experiments carried out to measure the apparent complex permittivity of the third sample; agreement between the measured and the calculated values is very good. This justifies the validity of the method presented in this paper, when used to determine the dimension-independent intrinsic complex permittivity and permeability of Mn-Zn ferrites