Development of polyurethane elastomer composite materials by addition of milled fiberglass with coupling agent

Polyurethane elastomer composites were developed using milled fiberglass and their mechanical properties were studied. In particular, the organically chemical treatment of the milled fiberglass was investigated in detail. It was demonstrated that both strength and toughness of the resulting elastomer composites were improved considerably with the addition content of fiberglass. Furthermore, it was indicated that the optimal properties can be achieved by the proper addition of milled fiberglass that was chemically treated using coupling agent.     

Preparation of BaMgAl10O17∶Eu2+ and Its Phase Behavior in Microemulsion System

BaMgAl10O17∶Eu2 (BAM) was prepared in the microemulsion system and its phase behavior was studied. There exists a small region in the reverse microemulsion system where the dispersed particles are of spherical form. In this way, BAM blue phosphor with good dispersion can be synthesized. The microemulsion phase diagrams of the pseudo-ternary system (Triton X-100/cosurfactant-oil-BAM brine) were first established intuitively by the dilution method. The microstructure of microemulsions was determined through eyeballing, conductance technique, and polar optical microscopy. Its phase behavior is affected by various factors, such as temperature (room temperature, 30, 40 ℃), oil, surfactants, and cosurfactants in microemulsions. According to the phase diagrams, the microemulsion system of Triton X-100/1-hexanol-hexane-BAM brine was chosen to prepare the precursor. The BAM phosphor can be obtained via sintering the precursor at a comparatively low temperature. The phosphors were characterized by XRD and vacuum ultraviolet (VUV) spectra.     

A Recursive Frequency Estimator Using Linear Prediction and a Kalman-Filter-Based Iterative Algorithm

This paper proposes a new Kalman-filter-based recursive frequency estimator for discrete-time multicomponent sinusoidal signals whose frequencies may be time-varying. The frequency estimator is based on the linear prediction approach and it employs the Kalman filter to track the linear prediction coefficients (LPCs) recursively. Frequencies of the sinusoids can then be computed using the estimated LPCs. Due to the coloredness of the linear prediction error, an iterative algorithm is employed to estimate the covariance matrix of the prediction error and the LPCs alternately in the Kalman filter in order to improve the tracking performance. Simulation results show that the proposed Kalman-filter-based iterative frequency estimator can achieve better tracking results than the conventional recursive least-squares-based estimators.     

改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。     

Effects of compressive and tensile stress on the growth mode of epitaxial oxide films

Oxide films were deposited on different substrates by laser molecular beam epitaxy. Reflection high-energy electron diffraction was performed to in situ investigate the change of growth mode and the lattice relaxation during the growth. An asymmetrical phenomenon was found in the two kinds of strain states, compressive stress and tensile stress of heterostructures with different lattice mismatch. In the case of BaTiO₃/SrTiO₃ (2.2%), 2D layer-by-layer growth mode without lattice relaxation can be maintained for a longer period for BTO films on STO with compressive stress, comparing to STO films on BTO with tensile stress. When MgO films were deposited on SrTiO₃ with a large mismatch of 7.8%, compressive stress leads to rapid lattice relaxation with a very thin wet layer, and 3D strained island were observed. As a comparison, SrTiO₃ films on MgO with tensile stress were configured. No RHEED patterns can be observed duo to a large tensile stress.