卫生陶瓷贴牌（OEM）加工问题的探讨

前言 近20年来,随着改革开放和国民经济的飞速发展,我国建筑卫生陶瓷行业也得到快速发展,产量连年增长,成为世界上建筑卫生陶瓷的最大生产国和消费国,也是出口大国.2007年全国卫生陶瓷的产量达到15 000万件,占世界产量的40%,出口量达到5 525万件,占产量的40%.     

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

The cooling and solidification of melted drops during their movement in an immiscible cooling medium is widely employed for granulation in the chemical industry, and a study of these processes to provides a basis for the design of the granulation tower height and the temperature of the cooling medium is reported. A physical model of the cooling and solidification of the drop is established and the numerical calculation is performed. The influences of the key factors in the solidification, i.e., Bi number, drop diameter, temperature of the cooling medium, etc. are presented. The cooling and solidification during wax granulation in a water‐cooling tower and during urea granulation in an air‐cooling tower (spraying tower) are described in detail. Characteristics of the solidification and temperature distribution within the particle at different times are shown. The model and calculations can be used for structure design of the granulation tower and optimization of the operation parameters.     

Cholesterol‐imprinted polymer receptor prepared by a hybrid imprinting method

A novel cholesterol‐imprinted polymer (CMIP‐H) was prepared by a hybrid method of covalent imprinting and non‐covalent imprinting. This approach involves the copolymerization of a template‐containing monomer, cholesteryl 2‐hydroxyethyl methacrylate carbonate, and a cross‐linker, followed by hydrolysis to afford a flexible guest‐binding site accompanied with the easy and efficient removal of a ‘sacrificial spacer’. The effect of solvent on the binding capacity of CMIP‐H towards cholesterol was studied, indicating that a good binding capacity towards cholesterol could be achieved in a less‐polar solvent. The binding experiments of CMIP‐H towards a series of structural analogues of cholesterol, including cholesterol acetate, progesterone and stigmasterol, were carried out in hexane. The results showed that CMIP‐H almost did not bind cholesterol acetate at all because the hydrogen‐bonding site is blocked. It exhibited a similar binding towards both cholesterol and stigmasterol, but much higher binding towards progesterone. Copyright © 2005 Society of Chemical Industry     

Colour Centres and Energy Transfer in BaF2-xClx:Eu2+ Phosphors

The optical absorption spectra of BaF2-xClx:Eu2 after ultraviolet (UV) light excitation were investigated.The differences between the absorption spectra after and before excitation (DAS) were observed.The DAS increase at both the high and the low energy side of F band in BaF2-xClx:Eu2 after 245 nm UV light excitation.The bleach effect of UV light and the absorption of electrons in the valence band may account for the former and the formation of Fa centres (association of F(Cl-) centres), whose absorption band matches the HeNe laser better, may explain the latter.In the write-in process, the transfer of electrons is via tunneling.In the readout process, the transfer of electrons captured in F(F-) and Fa centres is more likely via tunneling, and that of F(Cl-) centres is more likely via conduction band.     

Broad-band MMICs based on modified loss-compensation method using 0.35-/spl mu/m SiGe BiCMOS technology

Using the concept of loss compensation, novel broad-band monolithic microwave integrated circuits (MMICs), including an amplifier and an analog multiplier/mixer, with LC ladder matching networks in a commercial 0.35-mum SiGe BiCMOS technology are demonstrated for the first time. An HBT two-stage cascade single-stage distributed amplifier (2-CSSDA) using the modified loss-compensation technique is presented. It demonstrates a small-signal gain of better than 15 dB from dc to 28 GHz (gain-bandwidth product=157 GHz) with a low power consumption of 48 mW and a miniature chip size of 0.63 mm² including testing pads. The gain-bandwidth product of the modified loss-compensated CSSDA is improved approximately 68% compared with the conventional attenuation-compensation technique. The wide-band amplifier achieves a high gain-bandwidth product with the lowest power consumption and smallest chip size. The broad-band mixer designed using a Gilbert cell with the modified loss-compensation technique achieves a measured power conversion gain of 19 dB with a 3-dB bandwidth from 0.1 to 23 GHz, which is the highest gain-bandwidth product of operation among previously reported MMIC mixers. As an analog multiplier, the measured sensitivity is better than 3000 V/W from 0.1 to 25 GHz, and the measured low-frequency noise floor and corner frequency can be estimated to be 20 nV/sqrt(Hz) and 1.2 kHz, respectively. The mixer performance represents state-of-the-art result of the MMIC broad-band mixers using commercial silicon-based technologies     

APT（STLRI）—1.78型单模光纤（缆）连接器简介

利用引进的制造技术和设备,制作出了 APT(STLRI)—1.78型系列化光纤连接器。     

In-Situ observation on microfracture behavior ahead of the crack tip in 63Sn37Pb solder alloy

in-situ transmission electron microscopy (TEM) tensile tests on as-cast and aged 63Sn37Pb solder alloys were conducted, and the fracture behavior in nanometer scale ahead of the crack tip was inspected and discussed. Results show that the fracture was completed by connecting the discontinuous cracks or voids. Dislocation behavior was concentrated along the grain boundaries for as-cast samples, and displayed mainly as dislocation climb. The crack was intergranular dominated under the lower strain rate. While remarkable mutual dislocation emission was detected in the aged solder. Transgranular cracks were dominant in the fractured area, and they propagated by linking up with the nanometer scale cracks ahead of the crack tips under the effective promotion of the inverse dislocation emission. At the same time, the partial interphase or intergranular cracks in the thinned area were also found. Under this condition, a new critical stress intensity factor K _c ^′ to define the mutual dislocation emission was proposed.     

Amorphous diffusion bonding of steel pipe and its impact toughness

An iron-based amorphous foil (FeNiCrSiB) was used as an interlayer for the amorphous diffusion bonding of low carbon steel pipes under argon flux. The microstructure and mechanical properties of the joint were analyzed using an electron probe micro-analyzer (EPMA), tensile test, bending test and impact test. The results show that the joint microstructure resembles that of the base metal and no precipitates form at the joint. Melting point depressants (B, Si) diffuse far away from the joint and the base metal element is homogenous across the joint. The joint impact toughness is greater than the base metal toughness and the mechanical properties of the joint are similar around the pipe.