Experimental study on Ti+Nb bearing ultra-low carbon bake hardening sheet steel hot-rolled in the ferrite region

A Ti+Nb bearing ultra-low carbon bake hardening sheet steel hot-rolled in the conventional austenite region and in the ferrite region with lubrication was experimentally studied.Subsequent cold rolling and continuous annealing processes were also conducted.The results show that microstructures of ultra-low carbon bake hardening hot strips at room temperature are basically irregular polygonal ferrites.The yield strength,ultimate tensile strength,n value,and r value of the No.2 specimen hot-rolled in the ferr...     

不同剂量A群脑膜炎球菌多糖菌苗的反应

应用30和50μg A 群脑膜炎球菌多糖菌苗,接种不同年龄组儿童和青少年、观察其全身和局部反应及大面积普种的异常反应。结果表明:接种30和50μg 菌苗后全身和局部反应轻微,两种剂量的接种反应无差别,仅有两个点接种两个不同年龄组时出现50μg 的全身及局部反应高于30μg。普种50多万人均未发生异常反应。     

Oxidation Performance of Fe-Al/WC Composite Coatings Produced by High Velocity Arc Sprayed at 650 ℃

Fe-Al intermetallics with remarkable high-temperatureintensity and excellent erosion,high-temperatureoxidation and sulfuration resistance are potential lowcost high-temperature structural material.ProducingFe-Al/WC composite coating by high velocity arcspraying(HVAS)on structural materials would notonly obviate the problems faced in fabrication of thesealloys into useful shapes,but also allow the effectiveuse of their outstanding high-temperature performance,which might thus promisingly mak…     

反应磁控溅射MgO薄膜溅射模式的分形维表征

用反应磁控溅射的方法制备了MgO薄膜，基于原子力显微镜观测，并借助Fourier变换，计算了薄膜表面形貌的分形维数。发现分形维数变化对应于薄膜溅射模式的变化，二者之间有相关性，氧分压30％的分形维数是一个临界点，分形维数若发生明显跌落，意味着溅射模式发生变化，界于临界值两侧的分形维数，分别对应两种截然不同的溅射模式，与临界值对应的溅射状态则处于金属模式和氧化物模式的混和状态。     

热力管线中不锈钢波纹管破裂原因分析

采用金相显微镜和扫描电镜分析了热力管线中不锈钢 波纹管破裂原因.该波纹管破裂特征与一般环向开裂不同，裂纹沿轴向扩展.分析认为，破裂 属穿晶应力腐蚀.引起应力腐蚀的介质是土壤中的氯化物，而应力则来自环向工作应力和冷 加工残余应力，而环向工作应力起主导作用。     

TiAl基双相合金相变的组织学研究

应用光学显微镜、透射电镜及X射线衍射研究了Ti—42at.—%Al和Ti—45at.—%Al两种合金的固溶处理后的快冷组织,证明其为过饱和的有序α_2单相组织,过饱和单相在1000-1100℃等温转变时,以准连续和不连续的机制分解成为γ+α_2两相。准连续转变中包括γ片析出和胞状化两个阶段,并在原始α_2晶界处形成锯齿形边界。     

我国的静电喷涂枪技术评述

就我国涂装用各种静电喷枪技术的现状分别作出了阐述和剖析,对有关企业制造或安全使用静电喷涂枪有积极意义。     

Fe和两种工业钢在500℃含氯气氛中ZnCl2-KCl盐膜下的腐蚀

研究了纯Fe,NF616和SS304钢在500℃含氯气氛中ZnCl2-KCl盐膜下的腐蚀行为.结果表明,3种材料都发生了加速腐蚀,生成了较厚的氧化膜,且在氧化膜与基体金属之间出现了熔融状氯化物混合盐.此外,合金在此环境中的抗腐蚀性随其Cr含量的提高而显著提高,这是在腐蚀过程中氧化膜内层出现了Fe-Cr尖晶石或Cr2O3阻挡了金属离子快速向外扩散的结果.讨论了材料发生加速腐蚀的机制.     

SELECTION OF THE PROCESS PARAMETERS FOR BATH AUTOGENOUS SMELTING OF COPPER

The process parameters for bath autogenous smelting of copper were selected based on dynamic analysis of the experimental data and calculation of the mathematical model. Selecting the slag composition of SiO_2/Fe=0.80 and CaO％=16. desulphur ratio less than 80 wt.-％ in system. and the copper content of matte less than 60 wt.-％, it is able to limit Fe_3O_4 formation and obtain a high desulphurization. The critical oxygen content of the blast increased with decrease of the sulphur content of the concentrate and increase of copper contents of the matte. If the copper contents of the concentrate are respectively of 30 and 35 wt.-％, the critical oxygen contents of the blast will be 48 and 69 wt.-％ respectively. The smelling rate increases linearly with the blast intensity. When the sulphur content of the concentrate is 30 wt.-％, the oxygen content of the blast 70 vol.-％ and the copper content of the matte 60 wt.-％, a blast intensityy of 700 Nm~3/m~2·h results in a smeling rate of 48.81 t/m~2·d.     

预氧丝在氧化镁/炭复合材料中的原位碳化及其强化作用

研究了碳纤维前驱体即预氧丝在氧化镁／炭复合材料中原位碳化及其强化作用。在氧化镁／炭复合材料中存在铝、镁添加剂时，预氧丝原位碳化后具有碳纤维的强度和强化效果。预氧丝在添加硅粉的氧化镁／炭材料中原位碳化时因与硅反应失去强度，在无抗氧化添加物的氧化镁／炭材料中原位碳化后，预氧丝因氧化失去强度，对基体无强化作用。