Deformation behavior of HCP Ti-Al alloy single crystals

Single crystals of Ti-Al alloys containing 1.4, 2.9, 5, and 6.6 pct Al (by weight) were oriented for 〈a〉 slip on either basal or prism planes or loaded parallel along the c-axis to enforce a nonbasal deformation mode. Most of the tests were conducted in compression and at temperatures between 77 and 1000 K. Trace analysis of prepolished surfaces enabled identification of the twin or slip systems primarily responsible for deformation. Increasing the deformation temperature, Al content, or both, acted to inhibit secondary twin and slip systems, thereby increasing the tendency toward strain accommodation by a single slip system having the highest resolved stress. In the crystals oriented for basal slip, transitions from twinning to multiple slip and, finally, to basal slip occurred with increasing temperature in the lower-Al-content alloys, whereas for Ti-6.6 pct Al, only basal slip was observed at all temperatures tested. A comparison of the critically resolved shear stress (CRSS) values for basal and prism slip as a function of Al content shows that prism slip is favored at room temperature in pure Ti, but the stress to activate these two systems becomes essentially equal in the Ti-6.6 pct Al crystals over a wide range of temperatures. Compression tests on crystals oriented so that the load was applied parallel to the c-axis showed extensive twinning in lower Al concentrations and 〈c+a〉 slip at higher Al concentrations, with a mixture of 〈c+a〉 slip and twinning at intermediate compositions. A few tests also were conducted in tension, with the load applied parallel to the c-axis. In these cases, twinning was observed, and the resolved shear for plastic deformation by twinning was much lower that that for 〈c+a〉 slip observed in compression loading. This article is based on a presentation made in the symposium entitled “Defect Properties and Mechanical Behavior of HCP Metals and Alloys” at the TMS Annual Meeting, February 11–15, 2001, in New Orleans, Louisiana, under the auspices of the following ASM committees: Materials Science and Critical Technology Sector, Structural Materials Division, Electronic, Magnetic & Photonic Materials Division, Chemistry & Physics of Materials Committee, Joint Nuclear Materials Committee, and Titanium Committee.     

Efficient mixed Timoshenko–Mindlin shell elements

The precise representation of rigid body motions in the displacement patterns of curved Timoshenko–Mindlin (TM) shell elements is considered. This consideration requires the development of the strain–displacement relationships of the TM shell theory with regard to their consistency with the rigid body motions. For this purpose a refined TM theory of multilayered anisotropic shells is elaborated. The effects of transverse shear deformation and bending‐extension coupling are included. The fundamental unknowns consist of five displacements and eight strains of the face surfaces of the shell, and eight stress resultants. On the basis of this theory the simple and efficient mixed models are developed. The elemental arrays are derived using the Hu–Washizu mixed variational principle. Numerical results are presented to demonstrate the high accuracy and effectiveness of the developed 4‐node shell elements and to compare their performance with other finite elements reported in the literature. Copyright © 2002 John Wiley & Sons, Ltd.     

Sequential tripping strategy for a transmission network back-upprotection expert system

This paper describes a sequential tripping strategy used in a wide area back-up protection expert system (BPES) to combat situations in which protection relays have maloperated or information is missing. The BPES is an innovative back-up protection scheme designed to prevent the occurrence of widespread blackouts. The BPES evaluates the certainty that transmission lines are likely to be affected by the fault and uses a sequential tripping strategy to isolate the fault if a firm decision is not available due to maloperated relays and/or missing information. The mode of analysis and the sequential tripping strategy ensures that the BPES will clear a fault at minimum risk to the network. An example is included to demonstrate how the certainty factor based sequential tripping strategy is employed by the BPES to clear a fault which occurred on the South Western part of the UK National Grid System     

Use of Mechanically Separated Spleen in Frankfurters

Beef and pork frankfurters were produced with 0, 5, 10, and 15% of the meat block being mechanically separated spleen (MSS). No fatting or peelability problems were experienced. Frankfurters were held at 2°C and evaluated at 2-wk intervals for 6 wk. Consumer panelists rated all products acceptable. A bi-monthly laboratory taste panel evaluated all frank furters (except the 15% product) acceptable during storage. Allo-Kramer shear values decreased with increased MSS, Frankfurters with 5, 10, and 15% MSS had 2.2, 3.9, and 4.9 times more iron than the control, respectively. Level of MSS did not influence bacterial numbers.     

Microwave signal generation using an optical self-heterodyne technique

A new technique for mixing optical waves to generate microwave-frequency signals using an injection laser diode and a fibre-optic interferometer is reported. A beat signal is produced by interfering light from the laser with light from the same laser emitted earlier at a different frequency. The interferometer consists of an evanescent-field fibre coupler joined to a length of single-mode optical fibre. The laser is tuned by pulsed or bipolar current waveforms superimposed on a DC bias current. Feedback from an external cavity stabilises the laser frequency and reduces its linewidth. Efficient mixing at difference frequencies from 250 MHz to 2 GHz is obtained, with spectral widths of less than 1% of the centre frequency.     

INHIBITION OF BOTULINUM TOXIN PRODUCTION BY PEDIOCOCCUS ACIDILACTICI IN TEMPERATURE ABUSED REFRIGERATED FOODS

The "Wisconsin process'(a combination of lactic acid starter culture and sucrose) has previously been shown to be effective in preventing botulinum toxigenesis in reduced nitrite bacon. This technology has been applied to other low-acid refrigerated foods which receive less than a 12D thermal process. A combination of Pediococcus acidilactici and dextrose was effective in preventing botulinum toxigenesis in chicken salad. When the chicken salad was temperature abused, the P. acidilactici catabolized available dextrose to lactic acid. Extracellular accumulation of the lactic acid caused a decrease in the pH of the product. Pathogen challenge tests verified that the rate and extent of lactic acid accumulation in the chicken salad during temperature abuse was sufficient to preclude botulinum toxigenesis. This technology has the potential to be of use in a variety of low-acid refrigerated foods.     

Bonding in cotton fiber from formaldehyde-free crosslinks

Cotton fabric was crosslinked with five agents, three of which were prepared form formaldehyde and two of which were formaldehyde-free. The formaldehyde-free agents produced less bonding between layers in the laminated microstructure of the cotton fiber. One agent, 4,5-dihydroxy-1,3-dimethyl-2-imidazolidinone, gave no evidence of any interlayer bonding. All five agents gave the same relationship between wrinkle recovery angle and molar substitution on the cotton up to moderate recovery angles, but only agents based on formaldehyde gave higher wrinkle recovery angles with additional reaction. Intralayer crosslinking did not reduce absorptivity, as shown by moisture regain and dye receptivity, but did restrict swelling in cupriethylenediamine hydroxide to the same extent as combined interlayer and intralayer crosslinking. The decrease in extensibility of treated fabric with increasing wrinkle recovery angle was the same with all agents. These results indicate the regions of the fiber that are important for each of these properties.     

New natural 2-acetoxy fatty acids using chemical ionization and electron impact mass spectrometry

The phospholipids of the spongePolymastia gleneni contain saturated long chain (C_22–30)-acetoxy fatty acids. Their structures were assigned based on chromatographic and spectrometric data as well as comparison with a synthetic sample. The use of capillary gas chromatography combined with chemical ionization and electron impact mass spectrometry was instrumental in the eludication of structures, since only a very small amount of crude lipids was available. Part 10 of “Phospholipids in Marine Organisms.” For Part 9 in this series, see reference 12.