全文获取类型
收费全文 | 155篇 |
免费 | 10篇 |
国内免费 | 30篇 |
专业分类
综合类 | 11篇 |
金属工艺 | 71篇 |
机械仪表 | 3篇 |
建筑科学 | 10篇 |
石油天然气 | 4篇 |
武器工业 | 1篇 |
一般工业技术 | 27篇 |
冶金工业 | 64篇 |
自动化技术 | 4篇 |
出版年
2024年 | 1篇 |
2023年 | 6篇 |
2022年 | 7篇 |
2021年 | 3篇 |
2019年 | 5篇 |
2018年 | 3篇 |
2017年 | 4篇 |
2016年 | 2篇 |
2015年 | 8篇 |
2014年 | 4篇 |
2013年 | 2篇 |
2012年 | 9篇 |
2011年 | 9篇 |
2010年 | 11篇 |
2009年 | 15篇 |
2008年 | 21篇 |
2007年 | 16篇 |
2006年 | 17篇 |
2005年 | 7篇 |
2004年 | 8篇 |
2003年 | 6篇 |
2002年 | 9篇 |
2001年 | 1篇 |
2000年 | 6篇 |
1999年 | 4篇 |
1998年 | 4篇 |
1996年 | 2篇 |
1993年 | 2篇 |
1992年 | 2篇 |
1990年 | 1篇 |
排序方式: 共有195条查询结果,搜索用时 15 毫秒
91.
氢对Ti_3Al基合金组织和超塑性能的影响 总被引:2,自引:0,他引:2
研究了红对Ti-24Al-14Nb-3V-0.5Mo(摩尔分数,%)合金的组织和超塑性能的影响。研究结果表明:渗氢使合金中B2相的体积分数增加,O相的体积分数下降。氢的存在使所研究合金超望变形的流变应力下降,下降幅度随氢含量的增加而增大。渗氢还使合金最佳超塑变形温度下降,最佳超塑变形速率向高速区移动。 相似文献
92.
93.
Alloys with different compositions in Mg-rich corner of Mg-Zn-La system at 400 ℃were prepared, the phase equilibrium in the Mg-rich corner of Mg-Zn-La system was determined by scanning electron microscopy(SEM), electron probe microanalysis based on energy dispersive X-ray spectroscopy (EPMA-EDS) and X-ray diffraction(XRD), and the isothermal section at 400℃ was established. The results show that there exists a ternary compound (T-phase) with a constant La content and changable Mg/Zn contents in the Mg-Zn-La system. The mole fraction of La in T-phase is about 8%, and that of Zn is from 16% to 43%, There exist a two-phase equilibrium which consists of T-phase plus hcp-Mg and a three-phase equilibrium which is composed of T-phase, hcp-Mg and a liquid phase (L-phase) at 400℃. The L-phase consists of 70% Mg, 30% Zn and is free of La. 相似文献
94.
通过硬度试验、拉伸试验、场发射扫描电镜(SEM)和透射电镜(TEM)观察,研究了Ti含量对IF钢再结晶温度的影响,并研究了不同Ti含量IF钢冷轧后在不同退火温度下的性能变化。结果表明,随着Ti含量的降低,IF钢中纳米析出物尺寸减小、分布稀疏且体积分数降低,钉扎作用减弱,再结晶温度下降;低Ti含量IF钢经630 ℃退火保温10 h后,屈服强度为198 MPa,抗拉强度为312 MPa,伸长率为36.78%,应变硬化指数(n值)为0.25,塑性应变比(r值)为2.42,符合超深冲钢的性能要求。 相似文献
95.
为了确定管材扩展组合模连续铸挤过程的变形力,将金属扩展组合模的模腔划分为导流区、扩展区、分流区、焊合区和定径区,分析各区金属的受力状态;用切块法建立各区应力计算公式。将金属连续铸挤型腔划分为液相区与半固态区、固态初始夹紧区和固态夹紧区,建立管材连续铸挤挤压力计算公式。在自行设计的连续铸挤机上进行铝管扩展组合模连续铸挤实验并测量其挤压力,获得的径向挤压力实验结果与理论计算结果吻合。 相似文献
96.
97.
研究了两种不同锰含量的高锰奥氏体钢在室温拉伸变形过程中力学性能和组织的变化.结果表明,随着钢中锰含量的变化,实验钢在流变应力的作用下出现相变诱导塑性的TRIP效应和孪晶诱导塑性的TWIP效应.在1×10-3 s-1的初始应变速率条件下,锰的质量分数为23.8%的实验钢可达到666 MPa的抗拉强度和67%的伸长率,而锰的质量分数为33%的实验钢可达到540 MPa的抗拉强度和97%的伸长率.并且在10-3~10-1 s-1的初始应变速率范围内,实验钢的抗拉强度对于流变应力不敏感,而实验钢的塑性则表现出一定的应变速率敏感性.由于该钢具有较好的综合力学性能,有望作为新一代高强度、高塑性汽车用钢. 相似文献
98.
耐热镁合金的合金设计及组织控制 总被引:3,自引:0,他引:3
结合近年来新型耐热稀土镁合金方面的研究进展,对耐热镁合金合金设计及组织控制的研究现状进行了简要评述,提出了尚待研究的问题,并对耐热镁合金的发展进行了展望. 相似文献
99.
For toe-shooting method, geomaterial constitutive models concerned are studied. Analysis shows that, although extensively applied in soil mechanics, due to its angular singularity of yielding surface, the Mohr-Coulomb model is not suitable for numerical simulations in large deformation; in this case the rock-fills may be regarded as the Drucker-Prager model and the seaooze as the Prandtl-Reuss model. By comparing experimental data with numerical results, the constitutive model of the seaooze is numerically verified. It shows that, in high strain rate stage forming the blasting crater, the seaooze behaves as ideal non-compressible fluid, while in low strain rate stage during which the reck-fills flow to the blasting crater, the viscosity of the seaooze is negligible. 相似文献
100.
数值模拟外转角半径及背压对纯钛ECAP变形的影响 总被引:4,自引:2,他引:2
使用DEFORM-3D软件模拟等通道转角挤压过程中外转角半径及背压对纯钛应力和应变分布的影响,探讨不同R值对材料流动的影响规律。结果显示:当R=6mm时,工件上下表面应力状况较为平衡,从而得到均匀的等效应变分布;当R<6mm时,在外转角形成的死区使材料之间相互搓动,导致工件底部区域出现剧烈畸变,工件不同区域之间的等效应变量差别较大;当R>6mm时,工件上表面与模具内转角之间的相互作用力增加,使工件顶部变形加剧并导致工件等效应变量不均匀;施加背压(pb)后,能有效提高等效应变量;适当的R值与pb匹配可使工件得到均匀的应变分布。 相似文献