Self-oscillating dimmable electronic ballast

This paper presents a simple alternative for an electronic ballast operating in self-sustained oscillating mode with dimming capability for fluorescent lamps. A simple modification in one of the gate drivers side circuit allows the lamp to dim without compromising the simplicity, reliability, and low cost which characterize the self-oscillating electronic ballast (SOEB). A qualitative analysis is presented to explain the behavior of the proposed self-oscillating electronic ballast with dimming feature. In addition, the stability and the key equations for the design are derived using the extended Nyquist criterion and describing function method. Experimental results from two 40-W electronic ballasts are presented to demonstrate the performance and to validate the analysis carried out.     

Scale Up from Small Oven-Drying Tests of Mineral Concentrate to Pilot-Scale Drying with a Heated Pad

While Fickian diffusion models are commonly used in other applications, there are few reports of them being applied to the batch drying of a mineral concentrate. Diffusion coefficients estimated from small-scale oven-drying tests were used to predict the drying behavior of a concentrate sample 1 m × 1 m in area and 50 cm deep, with a heated bottom pad. These pilot-scale tests included both daily turning of the sample and turning every three days. The excellent quantitative agreement between the predicted and observed pilot-scale behavior gives a high level of confidence in the model predictions and suggests that a Fickian diffusion model is adequate to predict the behavior of mineral concentrates at the low moisture contents used here.     

RF microelectronics for W-CDMA mobile communication systems

Third generation (3G) mobile communication systems are now just starting to be introduced. With a maximum data rate of 2 Mbit/s they will make wireless access to broadband data services like the Internet or video applications feasible. Most of the different physical layer technologies summarised under the acronym 3G are based on wideband-CDMA (W-CDMA), in contrast to existing second generation systems, which mostly use TDMA and FDMA. This has severe consequences for the design of the transceiver front-ends. During standardisation these were assumed to have an adequate RF performance yet they still present a performance bottleneck for the system. Starting with a short introduction to UMTS (Universal Mobile Telecommunications System)-the 3G standard to be deployed in Europe and already operating in Japan-this paper describes by way of example some of the test cases specified for UMTS and their impact on the analogue front-end. It is shown that accurate simulation of all the analogue and digital signal processing is necessary in order to predict the RF performance needed of today's commercial RFICs. The paper then presents and reviews some actual design examples. Finally, possible technologies and techniques for application in future mobile terminals are discussed     

LiNbO3 optical waveguides formed in a new proton source

Proton-exchanged planar waveguides have been fabricated on Z-cut and X-cut lithium niobate crystals by using a new proton source formed by a mixture of benzoic and adipic acids. Waveguide index profiles and optical characteristics have been obtained at different values of the adipic-benzoic acid concentration ratio. The samples have been structurally characterized by Raman and infrared (IR) absorption spectroscopy and double-crystal X-ray diffraction. Good quality samples have been fabricated by using 30 mol% ratio dilution, showing very low scattering levels (<0.1 dB/cm), relatively high electrooptic coefficient (r₃₃=0.88 pm/V), and low relative percentage of interstitial protons (26%). The main factor limiting the waveguide optical properties is the substitutional-interstitial proton ratio, which can be easily controlled to produce good quality waveguides. A demonstration of the repeatability of the exchange process in the acid mixture is also provided     

Metal diffraction gratings as laser power or energy dividers

The authors survey published results on the application of metal diffraction gratings as laser power or energy dividers when the laser beam is split into two approximately equal pans. The normal incidence of laser radiation on metal diffraction gratings of various profiles in the case of three propagating diffraction orders n=0, ±1 is discussed, along with the case of oblique incidence with only two propagating diffraction orders n=0 and n =–1.Translated from Izmeritel'naya Tekhnika, No. 2, pp. 22–26, February, 1994.     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.     

Polymeric prodrugs of mitomycin C designed for tumour tropism and sustained activation

Prodrugs of mitomycin C (MMC) based on soluble poly-[N-(2-hydroxyethyl)-L-glutamine] (pHEG) polymers have been evaluated as tumour-targeted drugs. These materials are designed to exploit the enhanced permeability of tumour vasculature, combining a passive tumour tropism with decreased systemic liberation of free MMC. A tri- or tetrapeptide linkage (e.g. Gly-Phe-Ala-Leu) between pHEG and the aziridine nitrogen of MMC can combine good hydrolytic stability with rapid cleavage by lysosomal enzymes, releasing free MMC. The conjugates showed decreased systemic toxicity and could be administered to mice at a total MMC dose of 15 mg/kg i.v., compared with just 6 mg/kg for free MMC. Conjugates also showed better activity against animal models of established tumours, achieving up to 77% increased life span (ILS) against solid P388 leukaemia, compared with only 23% for free MMC, and up to 121% ILS against solid C26 colorectal carcinoma, compared with no activity for the free drug. Improving the therapeutic index of anticancer drugs by combining tumour tropism with decreased systemic toxicity is a versatile approach that should produce a new generation of improved anticancer agents.     

Effect of postoperative mydriatics on the iris

PURPOSE: To assess the role postoperative mydriatics play after extracapsular cataract extraction (ECCE) and posterior chamber intraocular lens (IOL) implantation in causing iris modifications and in controlling inflammation. SETTING: Outpatients Department, Ninewells Hospital, Dundee, Scotland. METHODS: The prospective study comprised 136 patients who had standardized ECCE. Half the patients used a mydriatic for 2 weeks postoperatively. Anterior chamber activity, pain, and eye redness were evaluated at 2 weeks postoperatively; pupil shape, peripheral anterior synechias, IOL position, and iris adhesions, at 6 weeks. RESULTS: Iris-lens adhesions were significantly more common in the group using a mydriatic. There was no difference between the two groups in postoperative inflammation. CONCLUSION: Mydriatics should not be used routinely after ECCE with posterior chamber IOL implantation.