Effect of Temperature on Hydraulic Parameters of Cable-In-Conduit-Conductor of SST-1

Stable operation of superconducting magnets depend critically on the balance of heat deposition rate versus heat extraction rate by the cryo-coolant. Thus, the mass flow rate of the coolant in case of force-flow cooled superconducting magnet with Cable-In-Co-nduit-Conductor (CICC) construction becomes an important factor for optimum stability of magnets. The Toroidal and Poloidal Field magnets of Steady-state Superconducting Tokamak-1 (SST-1) is made of superconducting CICC with a void fraction of 40 %±2 %. For adequate cooling of magnets, supercritical helium at 4 bar and 4.5 K is forced-flown through the voids. Effect of temperature on mass flow rate and pressure drop in SST-1 CICC is studied in a 7 m long piece wound helically. The experimental friction factor of the CICC is also measured at different temperatures and flow rates and is compared with the standard Katheder equation and Tada equation. Also, based on the new findings obtained from the experimental results, the dimensionless Reynolds number has been slightly modified. This new number is used to propose a modified Katheder correlation for the friction factor in CICCs similar to that of SST-1.     

Freestanding chemiresistive polymer composite ribbons as high-flux sensors

Chemiresistive polymer composite ribbons that function as chemical detectors were produced from solution-cast films of polymers and carbon composites. An array with multiple polymer sensor threads was exposed to dimethyl methyl phosphonate, a nerve agent simulant, and different interferents in the vapor phase. Principal component analysis was used to differentiate between the analytes. The response of the ribbon sensors as a function of the carbon composite and the host polymer source was investigated. The freestanding threads/sensors were mounted into a cell perpendicular to the gas flow to provide little pressure drop and were imbedded into fabrics to provide an example of a small, low-cost, wearable chemical sensor. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Electrodeposition of copper into high aspect ratio PCB micro-via using megasonic agitation

This paper presents the use of micro-particle imaging velocimetry (micro-PIV) to analyse fluid flow and hence ion replenishment in PCB micro-via during the electroplating process. The cross section of a PCB via is fabricated in PMMA to allow optical access to the sample. Fluid flow within two 1:1 aspect ratio blind micro-vias, one with straight side walls and the other with tapered side walls were compared. Flow is also analysed in a 1:1 aspect ratio through via. Flow rates measured using micro-PIV are used to validate simulated flow models. The results show that there are increased flow rates within the blind via with tapered side walls. This goes some way to explaining the improved electroplating results obtained in industry when tapered vias are used. Initial experimental results using megasonic streaming to remove bubbles from blind micro-via and promote ion transportation within high aspect ratio PCB micro-via to enhance electrodeposition are also reported.     

Indoor emissions of total and fluorescent supermicron particles during HOMEChem

Inhalation of particulate matter is associated with adverse health outcomes. The fluorescent portion of supermicron particulate matter has been used as a proxy for bioaerosols. The sources and emission rates of fluorescent particles in residential environments are not well-understood. Using an ultraviolet aerodynamic particle sizer (UVAPS), emissions of total and fluorescent supermicron particles from common human activities were investigated during the HOMEChem campaign, a test-house investigation of the chemistry of indoor environments. Human occupancy and activities, including cooking and mopping, were found to be considerable sources of indoor supermicron fluorescent particles, which enhanced the indoor particle concentrations by two orders of magnitude above baseline levels. The estimated total (fluorescent) mass emission rates for the activities tested were in the range of 4-30 (1-11) mg per person meal for cooking and 0.1-4.9 (0.05-4.7) mg/h for occupancy and mopping. Model calculations indicate that, once released, the dominant fate of coarse particles (2.5-10 micrometer in diameter) was deposition onto indoor surfaces, allowing for the possibility of subsequent resuspension and consequent exposures over durations much longer than the ventilation time scale. Indoor coarse particle deposition would also contribute to soiling of indoor surfaces.     

Improving the dynamic performance of continuous-flow mixing of pseudoplastic fluids possessing yield stress using Maxblend impeller

The strategic approach of this article is to characterize the continuous-flow mixing of pseudoplastic fluids possessing yield stress in a stirred reactor with the Maxblend impeller. Dynamic experiments were carried out through the frequency-modulated random binary input of a brine solution to determine the extent of non-ideal flows. Mixing quality was determined on the basis of the extent of channeling and fully mixed volume. The effects of important parameters such as impeller speed (25–500 rpm), absence of baffles, fluid rheology (0.5–1.5%), fluid flow rate (3.20–14.17 L min⁻¹), and the locations of inlet/outlet on the dynamic performance of the continuous-flow mixing vessel were explored. The performance of the Maxblend impeller was then compared to the performances of various types of impellers such as close-clearance (an anchor), axial-flow (a Lightnin A320), and radial-flow (a Scaba 6SRGT) impellers. It was found when the channeling approached zero and the fully mixed volume approached the total fluid volume in the vessel, the power drawn by the A320 impeller and the Scaba impeller were about 2.9 and 4.3 times greater than that of the Maxblend impeller. Thus, the Maxblend impeller was able to drastically improve the performance of continuous-flow mixing with huge power savings. The mixing quality was further improved by optimizing the impeller speed, decreasing the fluid flow rate, decreasing the fluid concentration, and using bottom inlet- top outlet configuration. The flow non-ideality of the mixing system increased in the absence of the baffles. Thus, better mixing quality and more energy savings can be achieved by employing the findings of this study.     

Calcific mitral stenosis in the hemodialysis patient

The dialysis patient is prone to elevations in the calcium phosphorus product and hyperparathyroidism, which contributes to valvular and vascular calcification. We present the case of a young lady on chronic dialysis that developed mitral calcification complicated by severe mitral stenosis, caseous calcification and retinal embolization. She subsequently required mitral valve replacement.     

Keggin type inorganic–organic hybrid material containing Mn(II) monosubstituted phosphotungstate and S-(+)-sec-butyl amine: Synthesis and characterization

A new inorganic–organic POM-based hybrid material comprising Keggin type mono manganese substituted phosphotungstate and enantiopure S-(+)-sec-butyl amine was synthesized in an aqueous media by simple ligand substitution method. The synthesized hybrid material was systematically characterized in solid as well as solution by various physicochemical techniques such as elemental analysis, TGA, UV–vis, FT-IR, ESR and multinuclear solution NMR (³¹P, ¹H, ¹³C). The presence of chirality in the synthesized material was confirmed by CD spectroscopy and polarimeter. The above study reveals the attachment of S-(+)-sec-butyl amine to Keggin type mono manganese substituted phosphotungstate through N → Mn bond. It also indicates the retainment of Keggin unit and presence of chirality in the synthesized material. An attempt was made to use the synthesized material as a heterogeneous catalyst for carrying out aerobic asymmetric oxidation of styrene using molecular oxygen. The catalyst shows the potential of being used as a stable recyclable catalytic material after simple regeneration without significant loss in conversion.     

Stochastic nonlinear failure analysis of laminated composite plates under compressive transverse loading

This paper present the second ordered statistics of first-ply failure response of laminated composite plate with random material properties under random loading. The basic formulation is based on higher order shear deformation plate theory (HSDT) with the geometrically nonlinearity in the von-Karman. The direct iterative based C⁰ nonlinear finite element method combined with mean centered first order perturbation technique developed by the authors are extended and successfully applied nonlinearity for failure problem with a reasonable accuracy to predict the second order statistics (standard deviation) of first-ply failure response using Tsai-Wu and Hoffman failure criterion with macroscopic analysis. Typical numerical results for various combinations of boundary conditions, plate thickness ratios, aspect ratios, laminates scheme and layers, elastic modulus ratios have been presented to illustrate the application of developed procedure. Some new results are presented and examined which clearly demonstrated the importance of the randomness in the system parameters in the failure response of the structures subjected to transverse loadings.     

Factors influencing the crushing strength of some Aegean sands

Engineering properties of sands mainly depend on the integrity of the particles, which in turn has a strong bearing on their crushing strength. Seven different Aegean sands were tested for mineralogy, particle shape, size and specific gravity and the influence of aspect ratio, particle composition, particle shape and size on the crushing strength was examined. As the Aegean sands have a small range of sphericity and roundness, crushing strength tests were also performed on five Anatolian sands. A multiple regression analysis was carried out and an equation proposed to determine the crushing strength value of the Aegean sands. The computed values were found to be in good agreement with those obtained from the experimental investigations. It is concluded that the equation is sufficiently accurate to be a useful, time- and cost-effective way of obtaining crushing strength estimations at the preliminary stage of site investigations.