Effect of heme and vacuole deficiency on FRE1 gene expression and ferrireductase activity in Saccharomyces cerevisiae

Doppler sonography of the fetal descending aorta, renal artery, middle cerebral artery and umbilical artery in a population of 74 fetuses with a abdominal circumference below the fifth percentile of the reference limits were done. All fetuses were free from structural and chromosomal abnormalities. The pulsatility- and the resistance indices as well as the ratios between these indices from peripheral and cerebral vessels were calculated and correlated to the fetal distress. The measurement of the pulsatility index of the middle cerebral artery provided the best results in predicting the development of fetal distress. Better results were achieved by the use of ratios of pulsatility-indices of various vessels than by the examination of the vessels alone. Our results suggest the usefulness of the examination of the middle cerebral artery and their ratios compared to the renal artery.     

Analysis of a soliton-based logic module for a ring network

We analyze and numerically study the code-matching logic module that is the central element in a proposed soliton-based ring network system running at peak rates of 100 Gb/s. The proposed network is packet-switched, and fast logic is required to route each packet. That is the function of the code-matching logic module, and four soliton logic gates that can perform fast logic are the key devices in its design. The behavior of the code-matching logic module is governed by a large set of parameters, and we simulate it by varying many of these parameters. The physical effects that occur in these devices and their significance are analyzed. The results indicate that the logic module will work but within a restricted parameter range     

A contribution to the analysis of magnetic circuits excited bypermanent-magnets

In this paper, the influence of permeability on flux density in magnetic circuits is relegated to a minor importance. Here, permeability is considered as a mere measure of the effectiveness of amperian currents in increasing magnetic intensity. Based on this interpretation, the solution of problems related to magnetic circuits excited by permanent-magnets is reduced to the solution of problems related to magnetic circuits excited exclusively by energized coils     

Process-based cost modeling of photonics manufacture: the cost competitiveness of monolithic integration of a 1550-nm DFB laser and an electroabsorptive modulator on an InP platform

The monolithic integration of components holds promise to increase network functionality and reduce packaging expense. Integration also drives down yield due to manufacturing complexity and the compounding of failures across devices. Consensus is lacking on the economically preferred extent of integration. Previous studies on the cost feasibility of integration have used high-level estimation methods. This study instead focuses on accurate-to-industry detail, basing a process-based cost model of device manufacture on data collected from 20 firms across the optoelectronics supply chain. The model presented allows for the definition of process organization, including testing, as well as processing conditions, operational characteristics, and level of automation at each step. This study focuses on the cost implications of integration of a 1550-nm DFB laser with an electroabsorptive modulator on an InP platform. Results show the monolithically integrated design to be more cost competitive over discrete component options regardless of production scale. Dominant cost drivers are packaging, testing, and assembly. Leveraging the technical detail underlying model projections, component alignment, bonding, and metal-organic chemical vapor deposition (MOCVD) are identified as processes where technical improvements are most critical to lowering costs. Such results should encourage exploration of the cost advantages of further integration and focus cost-driven technology development.     

Impurity Distribution Behavior in Caprolactam Extraction with Environmentally Benign Mixed Solvents

In a previous study a solvent mixture of heptane containing 40 mass % heptanol was selected as an alternative in the industrial extraction of caprolactam to replace benzene, toluene, or chlorinated hydrocarbons. This work reports the equilibrium distribution ratio of caprolactam and four model impurities of organic nature, namely, cyclohexanone, aniline, n‐methylcaprolactam, and cyclohexane‐carboxamide, comparing the mixed solvents with toluene as a reference. The resulting phase equilibria were interpreted using the equilibrium stage model. Based on these calculations it was found that, compared to toluene, the co‐extracted fraction of cyclohexanone and aniline was higher, that of n‐methylcaprolactam was comparable, and that of cyclohexane‐carboxamide was lower using the mixed solvent. Overall, the mixed solvent reduced the fraction of co‐extracted impurities by almost 10 %.     

Development of heat-and impact-resistant coatings for main pipelines

We have developed composite layered temperature-resistant silicon-organic sandwich-type coatings with thin polyurethane silicon-organic interlayers. We used the following materials as binding components: KO 921 silicon-organic lacquer with addition of éD-20 epoxy resin for prime coat, the same lacquer with addition of PZ 1040 S polyurethane elastomer for thin soft interlayers, and only KO 921 lacquer for thick hard layers. The mineral filler represented a mixture of coal ash and omiacarb in proportion 70 / 30 mass %. We have manufactured and tested laboratory specimens with two hard layers and two interlayers as well as with three hard layers and two thin interlayers. We have established that the developed composite layered coatings exceed, in their basic characteristics, the requirements of the State Standard Committee of Ukraine and foreign normative documents for the rust protection of steel main pipelines. Our coatings possess high impact strength, heightened elasticity and adhesion strength and, as to their electrical insulating characteristics, exceed these requirements by an order of magnitude. We note the complexity of the technology of applying layered composite coatings and the necessity of its improvement. __________ Translated from Fizyko-Khimichna Mekhanika Materialiv, Vol. 42, No. 4, pp. 59–65, July–August, 2006.     

Surface leakage currents in SiN/sub x/ passivated AlGaN/GaN HFETs

A novel guarded surface leakage test structure is used to isolate the surface and bulk leakage contributions to gate current in AlGaN/GaN HFETs. Passivation with various recipes of SiN/sub x/ always resulted in the commonly observed increase in gate leakage, which was found to be dominated by bulk leakage through the AlGaN. However, high temperature deposited SiN/sub x/ recipes gave a 1-2 orders reduction in surface leakage, whereas low temperature deposition gave an increase. Gate lag measurements were found to correlate closely with the surface leakage component, giving direct evidence that the key device problem of current slump is associated with current flow at the AlGaN surface.     

Creating advanced functions on network processors: experience and perspectives

In this article we present five case studies of advanced networking functions that detail how a network processor (NP) can provide high performance and also the necessary flexibility compared with ASIC. We first review the basic NP system architectures, and describe the IBM PowerNP architecture from the data plane as well as the control plane point of view. We introduce models for the programmer's views of NP that facilitate a global understanding of NP software programming. Then, for each case study, we present results from prototypes as well as general considerations that apply to a wider range of system architectures. Specifically, we investigate the suitability of NP for QoS (active queue management and traffic engineering), header processing (GPRS tunneling protocol), intelligent forwarding (load balancing without flow disruption), payload processing (code interpretation and just-in-time compilation in active networks), and protocol stack termination (SCTP). Finally, we summarize the key features as revealed by each case study, and conclude with remarks on the future of NP.