Turbulent natural convection in an enclosure with localized heating from below

This study reports the results of a numerical investigation of turbulent natural convection in a square enclosure with localized heating from below and symmetrical cooling from the vertical side walls. The present study simulates the case of an accidental heat generation due to fire in a typical isolated building of a nuclear reactor or electronic components cabin. The source of fire is considered to be centrally located at the bottom wall with different heated widths, which is assumed to be either isothermal or with isoflux. For the purpose of the analysis, the source length is varied from 20 to 80% of the total width of the bottom wall. The top wall and the unheated portion of the bottom wall are considered to be adiabatic, whereas sidewalls are isothermal. Steady as well as transient forms of two-dimensional Reynolds–Averaged-Navier–Stokes equations and conservation equations of mass and energy, coupled with the Boussinesq approximation, are solved by the control volume based discretisation method employing the SIMPLE algorithm for pressure–velocity coupling. Turbulence is modeled using the standard k–ε model. Rayleigh number, Ra, based on the enclosure height is varied from 10⁸ to 10¹². Stream lines and isotherms are presented for various combinations of Ra and the heated width. A double cell flow pattern is observed with marginal loss in symmetry as Ra increases. The results are reported in the form of local and average Nusselt number on the heated floor. Correlations are developed to predict the heat transfer rates from the enclosure as a function of dimensionless heated width of the bottom wall and Ra, by least square linear regression analysis.     

Heat Transfer and Friction Characteristics of Perforated Fin with a Longitudinal Slot under Forced Convection

Extended surfaces are used in a variety of heat transfer applications owing to their ability in reducing the convection resistance by exposing a large surface area to the surrounding fluid. Surface modification in the form of perforations is a passive method of increasing the heat transfer rates with the additional benefit of weight reduction. This work deals with numerical investigation of heat transfer and friction from a perforated fin (with and without slot) subjected to forced convection. The perforated fin with slot has been found to have a maximum enhancement in heat transfer with the simultaneous increase in frictional losses versus that of a solid fin. Further, the perforated fin without slot has been able to transfer heat at a relatively higher rate with a considerable reduction in energy loss due to friction in comparison to a solid fin.     

Rare earth metal Gd influenced defect sites in N doped TiO2: Defect mediated improved charge transfer for enhanced photocatalytic hydrogen production

In this experimental studies, we report the synthesis of TiO₂ co-doped by both cationic and anionic sites by simple sol-gel based method. All the prepared samples exhibit the anatase crystalline morphology however, showed lattice distortion caused by the displacement of Ti⁴⁺ sites by Gd³⁺. The improved visible absorption is witnessed by the Gd and N co-doping with an assured redshift in the absorption edge. The N and Gd displacement inside TiO₂ lattice accompanied by the creation of OTiN and GdOTi bonds are characterized by the X-ray photoelectron spectra. The strong resonance signal by Gd4f electrons in the electron paramagnetic resonance spectroscopy further substantiate the displacement of lattice cites of TiO₂ by Gd³⁺ ions. The longevity of the photo produced charges observed in fluorescence spectra of Gd and N co-doped TiO₂ is because of the effective transfer of charges to the defect sites. The aforementioned catalysts are tested for their capacity for the H₂ production from water splitting. The 2 wt% gadolinium and nitrogen co-doped TiO₂ has shown 10764 μmol g^?1 H₂ production which is 26 times higher than the commercial Degussa P-25 catalyst. The enhanced activity for hydrogen production can be attributed to factors such as increased absorptivity under visible light and effective charge carrier separation.     

Blast Fragility and Sensitivity Analyses of Steel Moment Frames with Plan Irregularities

Fragility functions are determined for braced steel moment frames (SMFs) with plans such as square-, T-, L-, U-, trapezoidal-, and semicircular-shaped, subjected to blast. The frames are designed for gravity and seismic loads, but not necessarily for the blast loads. The blast load is computed for a wide range of scenarios involving different parameters, viz. charge weight, standoff distance, and blast location relative to plan of the structure followed by nonlinear dynamic analysis of the frames. The members failing in rotation lead to partial collapse due to plastic mechanism formation. The probabilities of partial collapse of the SMFs, with and without bracing system, due to the blast loading are computed to plot fragility curves. The charge weight and standoff distance are taken as Gaussian random input variables. The extent of propagation of the uncertainties in the input parameters onto the response quantities and fragility of the SMFs is assessed by computing Sobol sensitivity indices. The probabilistic analysis is conducted using Monte Carlo simulations. The frames have least failure probability for blasts occurring in front of their corners or convex face. Further, the unbraced frames are observed to have higher fragility as compared to counterpart braced frames for far-off detonations.     

Convective heat transfer enhancement techniques of heat exchanger tubes: a review

Heat exchangers are widely used in almost all industrial activities. Turbulent promoters used in heat exchanger tubes are an effective way of enhancing the performance. This paper summarises various investigations using twisted tapes, wire coil ribs, baffles, and swirl flow generators. The main objective of this paper is to review various studies, in which different obstacle roughness elements are used to enhance the rate of heat transfer in the heat exchanger tubes. It has been found that a lot of experimental and analytical studies reported in the literature. On the basis of correlations developed by various investigators an attempt has been made to compare the thermal hydraulic performance of obstacles in heat exchanger tubes. In this work, a comparative study is also carried out to select the best obstacle roughness shapes for higher heat transfer rate and low pressure drop losses.     

Incident photon energy and Z dependence of L X-ray relative intensities

The intensity ratios, I_Lk/I_Lα1 (k = l, η, α₂, β₁, β_2,15, β₃, β₄, β_5,7, β₆, β_9,10, γ_1,5, γ_6,8, γ_2,3, γ₄), have been evaluated for elements with atomic number 36 ? Z ? 92 at incident photon energies ranging E_L1 < E_inc ? 200 keV using currently considered to be more reliable theoretical data sets of different physical parameters, namely, L_i (i = 1-3) subshell photoionization cross sections based on the relativistic Hartree-Fock-Slater model, the X-ray emission rates based on the Dirac-Fock model, and the fluorescence and Coster-Kronig yields based on the Dirac-Hartree-Slater model. At incident photon energies above the K-shell ionization threshold, the contribution to the production of different L X-ray lines due to the additional L_i (i = 1-3) subshell vacancies created following decay of the primary K-shell vacancies have also been included in the present calculations. The important features pertaining to dependence of the tabulated intensity ratios on the incident photon energy and atomic number have been discussed.     

QoS aware and fault tolerant handovers in software defined LTE networks

Wireless Networks - In order to handle a huge number of mobile users connections and their requirements like higher throughput, lower delay and seamless mobility, telecom operators have started...     

Comprehensive review for energy efficient hierarchical routing protocols on wireless sensor networks

Wireless Networks - In recent years, wireless sensor networks (WSNs) have played a major role in applications such as tracking and monitoring in remote environments. Designing energy efficient...     

Hot boning of intact carcasses: a procedure to avoid central nervous system self-contamination in beef and beef products

Compared with traditional boning of split refrigerated carcasses, hot boning of intact carcasses (the removal of meat from the skeleton prerigor) provides several commercially important cuts, may improve quality and reduce refrigeration costs, and may reduce the contamination of carcasses with central nervous system (CNS) tissue. In a comparative study of hot boning of intact and split carcasses, the CNS tissue contamination of intact carcasses was negligible (as measured with the CNS-related proteins glial fibrillary acidic protein and S-100 protein), but split carcasses were highly contaminated. The same trends were observed for dissection worktables used during the boning process. Most current boning plants have processing lines that are organized for boning carcass quarters, where the carcasses, in addition to transversal division, also are split horizontally. This part of the boning process was incorporated in the design of our study. Nine of the 18 intact carcasses were split horizontally between thoracic vertebrae 10 and 11 before they were hot boned. CNS tissue contamination was not detected on the carcass site related to this procedure. The amount of CNS tissue contamination was similar in boned cuts and minced meat from split and intact carcasses, except in the forerib. Boning of split carcasses appears to reduce CNS tissue contamination significantly to a level comparable to that of intact hot-boned carcasses.     

Production Equations for Unsteady-State Construction Processes

The production equation called Little’s law has been applied to construction data recently. However, Little’s law was derived for steady-state conditions assuming constant input and output rates and long production runs. Production in construction is inherently temporary, and learning curves and environmental influences often render input and output rates unequal and nonlinear. Starting with a conservation of mass formulation, general equations for work-in-process and cycle time for unsteady-state conditions and limited run production are developed. The motivation behind these equations is to explain common trends in production variables seen on construction projects. Previous studies have shown that when output from a construction production system is drastically increased, a significant upward impact is also seen on cycle time and work-in-process, and this work provides underlying theory and equations to explain these trends. Cycle time and work-in-process equations are presented as functions of time and on average. Data from construction activities are used to show that unsteady-state conditions commonly occur. Reasonable simplifications of the general equations provide guidelines for buffer sizing and resource allocation decisions.