Factors affecting cloud point analysis of palm oleins

Some of the factors affecting cloud point determination of palm oleins are described. These are the type of container used, method of stirring, rate of stirring and bath temperature. The repeatability and reproducibility standard deviations of the method are determined from collaborative trials. Recommendations for the test are made to reduce the large variations among laboratories.     

Stability studies on methyl and ethyl fatty acid esters of sunflowerseed oil

Fatty acid esters, high in linoleic acid, were prepared and stored for long-term engine tests. Storage tests with these esters were undertaken to obtain more information on optimal storage requirements and general stability characteristics. Samples were kept at three temperature levels (20 C, 30 C and fluctuating around 50 C) for a 90-day period and were removed at regular intervals for chemical and physical analysis. The influence of air, temperature, light, TBHQ and contact with mild steel was evaluated by comparing the free fatty acid, peroxide, anisidine, ultraviolet absorption, viscosity and induction periods. A statistical model was used to evaluate the data and to reduce the large number of data points to comparable curves. Storage of esters in contact with air, especially at a temperature above 30 C, resulted in significant increases in peroxide, ultraviolet absorption, free fatty acid, viscosity and anisidine values. Exclusion of air retarded oxidation at all temperature levels. A direct relationship between viscosity increases and oxidation parameters was evident. Exposure to light caused a small increase in the oxidation parameters of esters stored at the highest temperature level. Addition of TBHQ prevented oxidation of samples stored under moderate conditions. Under unfavorable storage conditions the anti-oxidant was no longer effective. Mild steel had very little effect on the oxidation parameters. Only the anisidine values of samples stored at the highest temperature level were slightly increased. Methyl esters performed slightly better than ethyl esters during the storage test. The following practical guidelines for storage of fatty acid ester fuels are: (i) airtight containers should be used; (ii) the storage temperature should be <30 C; (iii) mild steel (rust free) containers may be used, and (iv) TBHQ has a beneficial effect on oxidation stability.     

A test for the statistical significance of DNA sequence similarities for application in databank searches

A method is developed, based on word-searching, which provides a rapid test for the statistical significance of DNA sequence similarities for use in databank searching. The method makes allowance for the lengths and dinucleotide compositions of the sequences being compared. A way is also described to calculate the power of the test, i.e. the probability of detecting a given similarity as being statistically significant. The effects on the power of the test of the scoring method, word length, sequence length, and sequence composition are examined. A novel scoring method is shown to be superior to the method currently used in most word-searching algorithms.     

Use of electrochemical oxidation process as post-treatment for the effluents of a UASB reactor treating cellulose pulp mill wastewater.

The main purpose of this study was to evaluate the performance of the electrochemical oxidation process as a post-treatment for the effluents of a bench-scale UASB reactor treating simulated wastewater from an unbleached pulp plant. The oxidation process was performed using a single compartment cell with two plates as electrodes. The anode was made of Ti/Ru0.3Ti0.7O2 and the cathode of stainless steel. The following variables were evaluated: current density (75, 150 and 225 mA cm(-2)) and recirculation flow rate in the electrochemical cell (0.22, 0.45 and 0.90 L h(-1)). The increase in current density from 75 to 225 mA cm(-2) did not increased the color removal efficiency for the tested flow rates, 0.22, 0.45 and 0.90 L h(-1), however the energy consumption increased significantly. The results indicated the technical feasibility of the electrochemical treatment as post-treatment for UASB reactors treating wastewaters from pulp and paper plants.     

Biochemical oxidation of caprolactam-containing wastewater from the production of synthetic fibres

Conclusions The chemical mutagenesis method is recommended for use in local purification installations for cleaning up of caprolactam-containing wastewater.Use of this method permits one to carry out a biochemical clean-up of wastewater having a caprolactam content up to 600 mg/liter while increasing the oxidative power of the aeration tank by a factor of two.Translated from Khimicheskie Volokna, No. 6, p. 46, November–December, 1985.     

Improving the Public Health Information Network through Semantic Modeling

The US Centers for Disease Control and Prevention (CDC) created the Public Health Information Network to advance fully capable, interoperable information systems in public health organizations. PHIN prioritizes public health information systems' functional requirements, capabilities, performance measures, and operational characteristics while letting the architects of those systems choose enabling approaches, methods, and concepts to meet the requirements. PHIN also provides a certification process for public health administrators to evaluate their information infrastructure's quality. The certification process is important because affected organizations often depend on certification for continued funding.     

Numerical solution for shape optimization of an impactor penetrating into a semi-infinite target

The shape of the impactor with the maximum depth of penetration (DOP) for a given impact velocity is found using a numerical procedure for solving a corresponding non-classical variational problem. It is shown that the optimum shape in a general case is close to a blunt cone. The variation of the optimal shape of the impactor and the dependence of the DOP vs. the initial (impact) velocity and friction coefficient is studied. The analysis is performed also for optimal conical impactors.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.