Lossy magnetic energy storage units for improvement in automatic generation control

Fast-acting energy storage devices can effectively damp electromechanical oscillations in a power system, because they provide storage capacity in addition to kinetic energy of the generator rotor, which can share the sudden changes in power requirement. Earlier studies showed the effectiveness of superconducting magnetic energy storage (SMES) for this purpose. The present paper analyses the characteristics of lossy magnetic energy storage (LMES) and shows the effectiveness of small-sized LMES units in improving power system transient response. Computer studies show that the optimal parameter settings of the power system are changed with the addition of an energy storage element.     

Wavelet domain analysis for identification of vehicle axles from bridge measurements

Bridge weigh-in-motion (B-WIM) is a process by which the axle and gross vehicle weights of vehicles travelling at highway speeds can be determined from instrumented bridges. The traditional method of attaching strain transducers to the soffit of the bridge and placing axle detectors on the road surface has been replaced here by using additional transducers underneath the bridge for axle detection and nothing-on-the-road (NOR). This paper presents a wavelet based analysis of strain signals and shows the efficacy of using wavelets in pattern recognition of these signals. The transformed signals are used to identify axle passage and hence the vehicle velocity and the axle spacing. In addition to numerically generated strains, signals acquired from such a NOR instrumentation of a bridge in Slovenia have been analysed by the method of wavelet transformation to extract axle position information that was not readily detectable using existing methods.     

The Structure And Properties of a Thermo‐mechanically Processed Low Carbon High Strength Steel

Research efforts were given towards development of low carbon high strength steels since recent past. The present study deals with the development of a low carbon high strength steel alloyed with Mn, Ni, Mo, Cu and microalloyed with Ti and Nb. The steel was subjected to three stage controlled rolling operation followed by accelerated cooling. The structure and properties of the steel at various processing conditions were evaluated. Microstructural observation reveals predominantly lath martensite along with twinned martensite structure at all processing conditions. High strength values at higher finish rolling temperatures have been obtained due to fine martensitic structure along with tiny precipitates of microalloying carbide and carbonitride. The strength value increases marginally at lower finishing temperature due to comparatively finer lath size of martensite and increased precipitation density of carbides, carbonitrides along with Cu particles. The variation in impact toughness properties at different finish rolling temperatures is found to be negligible at ambient and subambient temperatures. The formation of stable and large TiN/TiCN particles during casting have impaired the impact toughness values at ambient and at ‐40°C temperatures.     

Swing-up and stabilization of a cart–pendulum system under restricted cart track length

This paper describes the swing-up and stabilization of a cart–pendulum system with a restricted cart track length and restricted control force using generalized energy control methods. Starting from a pendant position, the pendulum is swung up to the upright unstable equilibrium configuration using energy control principles. An “energy well” is built within the cart track to prevent the cart from going outside the limited length. When sufficient energy is acquired by the pendulum, it goes into a “cruise” mode when the acquired energy is maintained. Finally, when the pendulum is close to the upright configuration, a stabilizing controller is activated around a linear zone about the upright configuration. The proposed scheme has worked well both in simulation and a practical setup and the conditions for stability have been derived using the multiple Lyapunov functions approach.     

Chemically deposited zinc oxide thin film gas sensor

Zinc oxide (ZnO) thin films were prepared by a low cost chemical deposition technique using sodium zincate bath. Structural characterizations by X-ray diffraction technique (XRD) and scanning electron microscopy (SEM) indicate the formation of ZnO films, containing 0.05–0.50 m size crystallites, with preferred c-axis orientation. The electrical conductance of the ZnO films became stable and reproducible in the 300–450 K temperature range after repeated thermal cyclings in air. Palladium sensitised ZnO films were exposed to toxic and combustible gases e.g., hydrogen (H₂), liquid petroleum gas (LPG), methane (CH₄) and hydrogen sulphide (H₂S) at a minimum operating temperature of 150 °C; which was well below the normal operating temperature range of 200–400 °C, typically reported in literature for ceramic gas sensors. The response of the ZnO thin film sensors at 150 °C, was found to be significant, even for parts per million level concentrations of CH₄ (50 ppm) and H₂S (15 ppm).     

Zoonoses and potential zoonoses transmitted by bats

PURPOSE: The purpose of this study was to develop an analytical method for the quantitative determination of the extent of neutralization of the carboxylic acid function in Carbopol 974P NF using Diffuse Reflectance Fourier Transform Infrared Spectroscopy (DRIFT) with Kubelka-Munk function analysis. METHODS: Carbopol 974P NF is a high molecular weight, chemically crosslinked polymer of acrylic acid, that has the C=O stretching band of the unionized carboxylic acid function at 1695 cm(-1). The quantitative determination of the extent of neutralization of the carboxylic acid function in Carbopol 974P NF is based upon the asymmetrical C=O stretching of the carboxylate anion at 1570 cm(-1) measured by DRIFT spectroscopy. RESULTS: To overcome spectral differences arising from sample preparation (powders, granules and tablets) and in an effort to increase the precision of the analytical method, the following approaches were used: (1) an internal standard, (2) first derivative of the spectrum to eliminate the effect of baseline drift and (3) the ratio of the first derivative of the C=O stretch of the carboxylate anion peak (1570 cm(-1)) in the neutralized Carbopol 974P NF to that of the peak of the internal standard (866 cm(-1)). The above data treatment techniques proved to be superior to the usual methods of peak height or peak area. The calibration curve of the ratio of the first derivative (1570 cm(-1)/866 cm(-1)) was a linear function of the mass of sodium carboxylate over the range from 0.0% to 100.0% neutralization of the carboxylic acid function in Carbopol 974P NF (Fig. 1a). No particle size or sample preparation effects were noted within the experimental error. CONCLUSIONS: DRIFT spectroscopy using the Kubelka-Munk function is a powerful tool for the routine determination of the extent of neutralization of the carboxylic acid function in Carbopol 974P NF in complex pharmaceutical formulations.     

A selective review of the finite element-ABC and the finite element-boundary integral methods for electromagnetic scattering

Annals of Telecommunications - This paper reviews two hybrid (frequency domain) finite element methods for electromagnetic scattering applications. Specifically, the progress over the last five...     

Race of new inorganic materials towards an ultra neolithic age

Three generally accepted generic groups of competitive engineering materials—metals, inorganic ceramics, as well as plastics and polymers belonging to the organic family—have been comparatively reviewed in the context of raw materials availability, energy requirements in production, engineering properties, combustibility and environmental friendliness. The intrinsic advantages of inorganic materials have been discussed. The shortcomings of engineering properties of inorganic materials and the new technologies of making chemically bonded ceramics or biomimic compounds from inorganic materials with improved toughness have been dealt with. The expanding application horizons of inorganic materials have been illustrated with the help of several novel products.