Polypyrrole composite membrane with high permeability prepared by interfacial polymerization

Novel polypyrrole (PPy)/polydimethylsiloxane (PDMS) composite membrane was prepared by interfacial polymerization to make a very effective gas separation membrane. We found that Polymerized PPy films as thin as ～200 nm could be chemically synthesized as freestanding membranes by using the interfacial polymerization technique. Additionally, we show that difference morphology of PPys films was obtained by controlling polymerization rate and more dense films were formed at low polymerization rate. Wide X-ray diffraction study showed the d spacing value of the PPy film decreased from 4.89 å to 3.67 å by the rate of polymerization decreases. According to d spacing value decrease, selectivity of a PPy composite membrane was increased dramatically and permeability was reduced gradually. This high selectivity was derived from d spacing closed to the kinetic diameter of nitrogen. These results indicated that the permeability is controlled by the diffusion coefficient, reflecting the packed structure of the PPy film. The highest selectivity value of composite membrane that was prepared by interfacial polymerization was O₂/N₂=17.2 and permeability for O₂ was 40.2 barrer.     

Electron spin resonance of thin films of organic light-emitting material tris(8-hydroxyquinoline) aluminum doped by magnesium

We have successfully observed electron spin resonance (ESR) signals of radical anions in thin films of tris(8-hydroxyquinoline) aluminum (Alq₃), a compound widely used as electron transporting and luminescent layers in organic light-emitting diodes. To obtain definitely defined radical-anion states in Alq₃, we doped Alq₃ with Mg by co-evaporating these materials. The obtained g value and peak-to-peak ESR linewidth ΔH_pp of Alq₃ radical anions are 2.0030 and 2.19 mT, respectively. Theoretical g value and hyperfine interactions were calculated by density functional theory method, which are in good agreement with the experimental results. A quantitative evaluation of doping concentration was performed. We confirmed that doped charges are localized at deep trapping sites by the lineshape analysis and temperature dependence of the ESR signals. Morphological investigation using transmission electron microscopy clarified that the co-evaporated Mg atoms form clusters.     

Ring-opening polymerization of ?-caprolactone by poly(propyleneglycol) in the presence of a monomer activator

The ring-opening polymerization of ?-caprolactone (CL) was induced by using polypropylene glycol (PPG) as an initiator in the presence of the monomer activator HCl·Et₂O to synthesize triblock copolymers composed of PPG and poly(?-caprolactone) (PCL). The degree of CL conversion and the molecular weight of PCL increased linearly with the polymerization time or with the feed ratio of CL to PPG in the presence of HCl·Et₂O in CH₂Cl₂ at 25 °C. The PCLs obtained had molecular weights close to the theoretical values calculated from the CL:PPG molar ratios and exhibited monomodal GPC curves with narrow polydispersity indexes. The apparent rate constant (k_app) for the polymerization of CL activated by HCl·Et₂O was greatly affected by the ratio of HCl·Et₂O/PPG. The activation energy for the polymerization of CL in this system was estimated to be 49.8 kJ/mol K. We successfully prepared PPG and PCL triblock copolymers using this activated monomer mechanism.     

Synthesis of mesoporous materials SBA-15 and CMK-3 from fly ash and their application for CO2 adsorption

A supernatant solution of silicate species extracted from coal fly ash in a power plant by alkali fusion was used in acidic condition to prepare a mesoporous silica SBA-15. The SBA-15 was used as a template for the synthesis of a mesoporous carbon CMK-3 using sucrose as a carbon source. Characterization of the produced mesoporous materials by XRD, N₂ adsorption-desorption, SEM, and TEM confirmed the formation of well-ordered hexagonal mesostructures. Textural properties were found close to those prepared by pure chemicals. SBA-15 after polyethyleneimine impregnation and CMK-3 were tested for carbon dioxide adsorption, successfully demonstrating the possibility of recycling the industrial waste product in a power plant into a useful adsorbent.     

Preparation of platinum-doped hollow spheres and their electrocatalytic activity in water electrolysis

Pure TiO₂ hollow spheres were prepared by using poly(styrene-methacrylic acid) latex particles as template; thereafter, titania hollow spheres were coated by platinum with an appropriate amount of choloroplatinic acid solution to obtain Pt/TiO₂ catalysts. The morphology and structure of nonstructural Pt/TiO₂ hollow spheres were characterized by BET, XRD, TGA, SEM and TEM analysis. In the samples, a remarkably uniform layer of Pt consisting of particles from 5 to 70 nm in size was formed over TiO₂ hollow spheres. We found the electrocatalytic nature of the samples by cyclic voltammetric experiment in acidic solution. The anodic peak current density of 20 wt% Pt-loaded TiO₂ hollow particles was observed 2.5 times higher than that of 5 wt% Pt/TiO₂ in the same experimental condition. Also, the anodic current density of 20 wt% Pt/TiO₂ hollow spheres calcined at various temperatures followed the order: 400 °C≈500 °C>600 °C. The electrocatalytic activity of the Pt-loaded TiO₂ hollow spheres depends on the amount of atomic platinum present in the sample; a higher concentration of platinum results in a larger current density value in anodic sweep, resulting in more oxygen production during electrolysis. Pt/TiO₂ hollow sphere catalysts have also shown long term electrocatalytic stability in acidic media.     

Effects of substituents of imidazolium cations on the performance of dye-sensitized TiO2 solar cells

Imidazolium iodides (Im⁺I⁻s) were synthesized with different substituents of the cation and used as electrolytes in dye-sensitized solar cells (DSSCs), and the effects of such substituents were investigated in terms of the photovoltaic performance of the cells. Synthesized iodides were verified by ¹H-NMR. Among the iodides, 1,3-diethylimidazolium iodide enabled a solar energy conversion efficiency of 4.8% for its DSSC, while 1-(4-acetophenyl)-3-ethylimidazolium iodide rendered an efficiency of 3.1% for its cell. In all cases the short-circuit photocurrent (J _sc) was found to increase with decrease in size of the substituent, which was also verified to be valid in the case of a quasi-solid state DSSC. Results are explained by the electrostatic interactions between solvated Im⁺ and negatively charged species based on the correlation between diffusion coefficients of I⁻ and I₃⁻ and J _sc values. These explanations are supported by steady-state voltammetry and electrochemical impedance spectroscopy (EIS).     

Physical modification of polypropylene: preparation of fibres dyeable with disperse dyes

Published literature from the past 30 years concerning the removal of dyes from textile effluent has been reviewed. The relationship between the bioelimination by activated sewage sludge and the molecular structure of anionic, water-soluble dyes has been examined. Bioelimination of many commercially available dyes as a mechanism for decolorising textile waste waters has been shown to be an inefficient process. However, the information collated will be used as the basis for development of novel reactive dyes for potential commercial application.     

Optimization of thermoelectric properties of n-type Bi_2(Te,Se)_3 with optimizing ball milling time

The thermoelectric properties at elevated temperature were investigated for n-type Bi2(Te,Se)3 which is obtained from ball milling processed powder with various milling times. Electrical properties such as electrical resistivity and Seebeck coefficient are clearly dependent on milling time, in which the carrier concentration is attributed to the change of the electrical properties. The concentrations of the defects are also varied with the ball milling time, which is the origin of the carrier concentration variation. Even though finer grain sizes are obtained after the long ball milling time, the temperature dependence of the thermal conductivity is not solely understood with the grain size, whereas the electrical contribution to the thermal conductivity should be also considered. The highest figure of merit value of ZT = 0.83 is achieved at373 K for the optimized samples, in which ball milling time is 10 h. The obtained ZT value is 48% improvement over that of the 0.5-h sample at 373 K.     

Grain Boundary Conformed Volumetric Mesh Generation from a Three-Dimensional Voxellated Polycrystalline Microstructure

We present a new comprehensive scheme for generating grain boundary conformed, volumetric mesh elements from a three-dimensional voxellated polycrystalline microstructure. From the voxellated image of a polycrystalline microstructure obtained from the Monte Carlo Potts model in the context of isotropic normal grain growth simulation, its grain boundary network is approximated as a curvature-maintained conformal triangular surface mesh using a set of in-house codes. In order to improve the surface mesh quality and to adjust mesh resolution, various re-meshing techniques in a commercial software are applied to the approximated grain boundary mesh. It is found that the aspect ratio, the minimum angle and the Jacobian value of the re-meshed surface triangular mesh are successfully improved. Using such an enhanced surface mesh, conformal volumetric tetrahedral elements of the polycrystalline microstructure are created using a commercial software, again. The resultant mesh seamlessly retains the short- and long-range curvature of grain boundaries and junctions as well as the realistic morphology of the grains inside the polycrystal. It is noted that the proposed scheme is the first to successfully generate three-dimensional mesh elements for polycrystals with high enough quality to be used for the microstructure-based finite element analysis, while the realistic characteristics of grain boundaries and grains are maintained from the corresponding voxellated microstructure image.     

A Synthetic Approach to Oligomeric Phenylethynylsilylenes

Oligomers consisting of alternating phenylethynyl and monosilyl or disilanyl moieties were synthesized in 15–64% precipitated yields by the reactions of dilithiated ethynylbenzene with dichlorodimethylsilane, dichlorodiphenylsilane, and 1,2-dichloro-1,1,2,2-tetramethyldisilane. Degrees of polymerization were fairly low due to chain termination reactions involving the deprotonation of ethynyl groups by aryllithium species. The presence of butyl chain ends was confirmed by ¹H and ²⁹Si NMR spectroscopy. ²⁹Si NMR spectroscopy was utilized to illustrate the random pattern of connectivity along the oligomer backbones. The oligomers exhibit fluorescent behavior in solution.