Experimental study on self-excitations in nitrogen-diluted laminar lifted butane flames

Laminar lifted butane flames diluted with nitrogen have been investigated experimentally to determine distinctive self-excitation regimes in the flame stability maps and also to elucidate the individual self-excitation characteristics. Self-excitations of lift-off height are classified into five regimes in laminar free-jet lift-off butane flames diluted with nitrogen: a stationary lifted regime (regime I), a heat-loss-induced self-excitation (regime II), a buoyancy-induced self-excitation due to flame flicker as well as a heat-loss-induced self-excitation (III), a combined form of an oscillation prior to blow-out and a heat-loss-induced oscillation (regime IV), and a combined form of an buoyancy-induced self-excitation and a heat-loss-induced oscillation as well as an additional buoyancy-driven self-excitation due to flame flicker (regime V). Extremely low-frequency (<0.1 Hz) self-excitation is caused by conductive heat loss from the premixed wings to the trailing diffusion flame and can be explained by a proposed mechanism. It is also found that the flame oscillation prior to flame blow-out is also caused by buoyancy and also significantly affected by the conductive heat loss from the premixed wings to the trailing diffusion flame, thereby showing that the frequency with nozzle exit velocity increases in the triple-flame propagation mode and then decreases in the flame-front propagation mode. Characterization of the individual self-excitation mode is presented and also discussed with Strouhal numbers and its relevant parameters through the analysis of power spectrum for temporal variation of lift-off height.     

Sugar recovery from rice straw by dilute acid pretreatment

Rice straw was pretreated with dilute sulfuric acid in order to decrease the amorphous portion and enhance enzyme accessibility. Dilute acid pretreatment process was optimized using a statistical method, and the relationships between each factor were investigated. Saccharification of pretreated rice straw was then performed, followed by fermentation of glucose, the hydrolysate of the saccharification process. The optimal dilute acid pretreatment process was as follows: temperature 110 °C, reaction time 14.02 min, and acid concentration 1.2%. Following dilute acid pretreatment, the solid weight was decreased by about 20% and 73.14% of the theoretical maximum content of xylose was solubilized. Glucose was recovered at a rate of about 90% at 24 h after rice straw was treated with dilute acid. Qualitative analysis such as SEM, XRD, and FT-IR were conducted after the pretreatment process, and the results supported the pretreatment process.     

Effect of Repetitive Lysine-Tryptophan Motifs on the Eukaryotic Membrane

In a previous study, we synthesized a series of peptides containing simple sequence repeats, (KW)_n–NH₂ (n = 2,3,4 and 5) and determined their antimicrobial and hemolytic activities, as well as their mechanism of antimicrobial action. However, (KW)₅ showed undesirable cytotoxicity against RBC cells. In order to identify the mechanisms behind the hemolytic and cytotoxic activities of (KW)₅, we measured the ability of these peptides to induce aggregation of liposomes. In addition, their binding and permeation activities were assessed by Trp fluorescence, calcein leakage and circular dichrorism using artificial phospholipids that mimic eukaryotic liposomes, including phosphatidylcholine (PC), PC/sphingomyelin (SM) (2:1, w/w) and PC/cholesterol (CH) (2:1, w/w). Experiments confirmed that only (KW)₅ induced aggregation of all liposomes; it formed much larger aggregates with PC:CH (2:1, w/w) than with PC or PC:SM (2:1, w/w). Longer peptide (KW)₅, but not (KW)₃ or (KW)₄, strongly bound and partially inserted into PC:CH compared to PC or PC:SM (2:1, w/w). Calcein release experiments showed that (KW)₅ induced calcein leakage from the eukaryotic membrane. Greater calcein leakage was induced by (KW)₅ from PC:CH than from PC:SM (2:1, w/w) or PC, whereas (KW)₄ did not induce calcein leakage from any of the liposomes. Circular dichroism measurements indicated that (KW)₅ showed higher conformational transition compared to (KW)₄ due to peptide-liposome interactions. Taken together, our results suggest that (KW)₅ reasonably mediates the aggregation and permeabilization of eukaryotic membranes, which could in turn explain why (KW)₅ displays efficient hemolytic activity.     

PG-2, a Potent AMP against Pathogenic Microbial Strains,from Potato (Solanum tuberosum L cv. Gogu Valley) Tubers Not Cytotoxic against Human Cells

In an earlier study, we isolated potamin-1 (PT-1), a 5.6-kDa trypsin-chymotrypsin protease inhibitor, from the tubers of a potato strain (Solanum tuberosum L cv. Gogu Valley). We established that PT-1 strongly inhibits pathogenic microbial strains, but not human bacterial strains, and that its sequence shows 62% homology with a serine protease inhibitor. In the present study, we isolated an antifungal and antibacterial peptide with no cytotoxicity from tubers of the same potato strain. The peptide (peptide-G2, PG-2) was isolated using salt-extraction, ultrafiltration and reverse-phase high performance liquid chromatography (RP-HPLC). Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF/MS) showed the protein to have a molecular mass of 3228.5 Da, while automated Edman degradation showed the N-terminal sequence of PG-2 to be LVKDNPLDISPKQVQALCTDLVIRCMCCC-. PG-2 exhibited antimicrobial activity against Candida albicans, a human pathogenic yeast strain, and Clavibacter michiganensis subsp. michiganensis, a plant late blight strain. PG-2 also showed antibacterial activity against Staphylococcus aureus, but did not lyse human red blood cells and was thermostable. Overall, these results suggest PG-2 may be a good candidate to serve as a natural antimicrobial agent, agricultural pesticide and/or food additive.     

Conjugated polymer mediated synthesis of nanoparticle clusters and core/shell nanoparticles

Two water soluble conjugated polymers, poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) and ammonium ion stabilized poly(phenylene vinylene) (P2), are found to be able to reduce noble metal ions to zero-valent metals via a direct chemical deposition technique. Au nanoparticle clusters can be obtained through reduction of Au³⁺ ions by PEDOT:PSS and the electronic coupling between them can be controlled by HAuCl₄ concentration. Core/shell Ag/polymer nanostructures are prepared from reduction of Ag⁺ ions by P2, which have a ppb detection limit for 4-MBA using surface-enhanced Raman spectroscopy (SERS). This conjugated polymer mediated synthesis of metal nanoparticles may open a new avenue for fabricating nanomaterials and nanocomposites with tunable optical properties that are dominated by their structure and electronic coupling between nanoparticles.     

Electrical conductivity and thermoelectric power studies of solution-combustion-processed Ca2.76Cu0.24Co4O9

Nanocrystalline Ca_2.76Cu_0.24Co₄O₉ powders (25 nm in crystallite size) are synthesized by the solution combustion method, using aspartic acid as the combustion fuel. In this study, we discuss the effect of sintering temperature on the microstructure and thermoelectric properties of Ca_2.76Cu_0.24Co₄O₉. The density and grain size increase with an increase in sintering temperature. The Ca_2.76Cu_0.24Co₄O₉ sintered at 900 °C shows the largest value of electrical conductivity and Seebeck coefficient, resulting in the largest power factor (3.8×10^?4 W m^?1 K^?2 at 800 °C). This value is more than 22 times larger than that of the Ca_2.76Cu_0.24Co₄O₉ sintered at 940 °C (1.7×10^?5 W m^?1 K^?2 at 800 °C).     

A green and facile one-pot synthesis of Ag–ZnO/RGO nanocomposite with effective photocatalytic activity for removal of organic pollutants

In this study, Ag–ZnO/reduced graphene oxide (Ag–ZnO/RGO) composite was synthesized by a green and facile one-step hydrothermal process. Aqueous suspension containing Ag and ZnO precursors with graphene oxide (GO) sheets was heated at 140 °C for 2 h. The morphology and structure of as-synthesized particles were characterized by field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy, and Photoluminescence (PL) spectroscopy which revealed the formation of composite of metal, metal oxide and RGO. It was observed that the presence of Ag precursor and GO sheets in the hydrothermal solution could sufficiently decrease the size of ZnO flowers. The hybrid nanostructure, with unique morphology, obtained from this convenient method (low temperature, less time, and less number of reagents) was found to have good photocatalytic and antibacterial activity. The perfect recovery of catalyst after reaction and its unchanged efficiency for cyclic use showed that it will be an economically and environmentally friendly photocatalyst.     

Site-specific growth and density control of carbon nanotubes by direct deposition of catalytic nanoparticles generated by spark discharge

Catalytic iron nanoparticles generated by spark discharge were used to site-selectively grow carbon nanotubes (CNTs) and control their density. The generated aerosol nanoparticles were deposited on a cooled substrate by thermophoresis. The shadow mask on top of the cooled substrate enabled patterning of the catalytic nanoparticles and, thereby, patterning of CNTs synthesized by chemical vapor deposition. The density of CNTs could be controlled by varying the catalytic nanoparticle deposition time. It was also demonstrated that the density could be adjusted by changing the gap between the shadow mask and the substrate, taking advantage of the blurring effect of the deposited nanoparticles, for an identical deposition time. As all the processing steps for the patterned growth and density control of CNTs can be performed under dry conditions, we also demonstrated the integration of CNTs on fully processed, movable silicon microelectromechanical system (MEMS) structures.     

Effects of Residual Stress on the Electrical Properties of PZT Films

The effects of the residual stress (either compressive or tensile) induced during the heat-treatment process on the electrical properties of Pb(Zr_0.52Ti_0.48)O₃ (PZT) films were investigated. The PZT films were deposited on platinized silicon substrates by the rf-magnetron sputtering method using a single oxide target. After their deposition, the films were bent elastically by means of a specially designed fixture during the annealing process. Residual stress was induced in the film by removing the substrate from the fixture after annealing. The ferroelectric and piezoelectric properties of the films were markedly changed by the residual stresses; the remnant polarization ( P _r) and saturation polarization ( P _sat) increased when a compressive stress was induced. On the other hand, the piezoelectric properties increased when a tensile stress was induced in the film.     

Photocatalytic degradation of methanol on titania and titania–silica aerogels prepared by non-alkoxide sol–gel route

Titania and titania–silica aerogels were prepared by alkoxide or non-alkoxide sol–gel route and subsequent supercritical drying with carbon dioxide at low temperature. The resulting aerogels having high surface area and mesoporosity were used as photocatalysts for gas phase methanol degradation reaction. Photocatalytic degradation reactions were carried out on titania and titania–silica aerogels, and commercial Degussa P-25 titania. The photocatalytic activities of titania and titania–silica aerogels were higher than that of the P-25. While the conversion of methanol degradation over the P-25 catalyst was only 50–60%, that for the titania aerogel was observed to be above 98% due to the higher specific surface area and the well developed mesoporous structure. In spite of lower titania contents, much higher surface area and high dispersion of titania of titania–silica aerogel gave rise to the high photocatalytic activity in comparison to those of titania aerogels. Moreover, titania–silica aerogel was also used for the photodegradation and adsorption hybrid system. It was observed that the high removal efficiency for methanol was caused by the combination of higher catalytic activity and adsorption capacity.