Simultaneous measurement of dissolved oxygen concentration and velocity field in microfluidics using oxygen-sensitive particles

This paper reports a technique for measuring the velocity and dissolved oxygen concentration (DOC) fields simultaneously in a micro-scale water flow using oxygen-sensitive particles (OSP) and a conventional microparticle image velocimetry method. The OSP were fabricated using a dispersion polymerization method by synthesizing platinum (II) octaethyporphyrin (PtOEP) with polystyrene, and used as tracer particles and oxygen sensors. An ultraviolet light-emitting diode with a wavelength of 385 nm was used as the excitation light source, and phosphorescence images of OSP were captured on a CMOS high-speed camera. The interrogation window concept was used to measure the DOC in water from the dispersed phosphorescence intensity distribution of OSP. The Stern–Volmer equations in the interrogation windows were obtained from in situ calibration. Water containing OSP with DOC values of 0 and 100 % were injected into a Y-shaped microchannel using a double loading syringe pump. The velocity and DOC field over the entire channel area were quantified.     

Effects of Annealing Temperature on Microstructure and Tensile Properties in Ferritic Lightweight Steels

An investigation was conducted into the effects of annealing temperature on microstructure and tensile properties of ferritic lightweight steels. Two steels were fabricated by varying the C content, and were annealed at 573 K to 1173 K (300 °C to 900 °C) for 1 hour. According to the microstructural analysis results, κ-carbides were formed at about 973 K (700 °C), which was confirmed by equilibrium phase diagrams calculated from a THERMO-CALC program. In the steel containing low carbon content, needle-shaped κ-carbides were homogeneously dispersed in the ferrite matrix, whereas bulky band-shaped martensites were distributed in the steel containing high carbon content. In the 973 K (700 °C)-annealed specimen of the steel containing high carbon content, deformation bands were formed throughout the specimen, while fine carbides were sufficiently deformed inside the deformation bands, thereby resulting in the greatest level of strength and ductility. These results indicated that the appropriate annealing treatment of steel containing high carbon content was useful for the improvement of both strength and ductility over steel containing low carbon content.     

Modeling for multilevel switching in oxide-based bipolar resistive memory

We report a physical model for multilevel switching in oxide-based bipolar resistive memory (ReRAM). To confirm the validity of the model, we conduct experiments with tantalum-oxide-based ReRAM of which multi-resistance levels are obtained by reset voltage modifications. It is also noticeable that, in addition to multilevel switching capability, the ReRAM exhibits extremely different switching timescales, i.e. of the order of 10(-7)?s to 10(0)?s, with regard to reset voltages of only a few volts difference which can be well explained by our model. It is demonstrated that with this simple model, multilevel switching behavior in oxide bipolar ReRAM can be described not only qualitatively but also quantitatively.     

Sunitinib release from biodegradable films of poly(l-lactide-co-caprolactone)

The aim of this study was to prepare sunitinib-loaded biodegradable films using poly(l-lactide-co-?-caprolactone) (PLCL) for anti-tumor drug delivery. Sunitinib-loaded PLCL film has a rough surface, while empty film has a smooth surface. PLCL film loaded with 5% (w/w) sunitinib showed an absence of a crystalline peak of sunitinib, while sharp peaks were observed at 10% (w/w) loading, indicating that sunitinib was molecularly distributed in the polymer matrix at 5% (w/w). A drug release study revealed an initial burst during the first 2 h, followed by continuous release until 24 h. Since weight loss of film was <10% for 1 week, drug release mechanism was dominantly dependent on the diffusion-mediated release of drugs to the medium. Sunitinib has a dose-dependent anti-proliferation effect against HuCC-T1 human cholangiocarcinoma cells in vitro. These results indicate that sunitinib-loaded PLCL film is a appropriate candidate as a vehicle for anti-tumor drug delivery.     

Layered Nanoprobe for Long‐Lasting Fluorescent Cell Label

A long‐lasting particle‐based fluorescent label is designed for extended cell imaging studies. This onion‐like nanoprobe is constructed through layer‐by‐layer fabrication technology. The nanoprobes are assembled with multiple layers of optically quenched polyelectrolytes, the fluorescence signal of which can be released later by intracellular proteolysis. Upon incubation with cells, the assembled nanoprobes are taken up efficiently. The tight packing and layered assembly of the quenched polyelectrolytes slow subsequent intracellular degradation, and then result in a prolonged intracellular fluorescence signal for up to 3 weeks with no noticeable toxicity.     

Effect of contact angle and drop spacing on the bulging frequency of inkjet-printed silver lines on FC-coated glass

The morphologies of inkjet-printed narrow silver lines on fluorocarbon film-coated glass substrates were measured with varying contact angles and drop spacing to study the actual stability of line printing by using a practical inkjet system. From a practical stability point of view, three types of the lines were observed: stable, unstable, and meta-stable. The stable lines were free from any bulging or breaking; the unstable lines had repetitive and periodic instabilities; and the meta-stable lines had no repetitive instability but had irregular bulges that appear sparsely. Unstable line printing resulted from either the dynamic or static instability of bead flow, which arose when the pressure-driven bead flow was too large or too small compared with droplet deposition rate, respectively. Whether the printing would be stable or meta-stable was determined by the anti-bulging stability of the flow against other disturbances. The anti-bulging stability increased when the bead flow rate was balanced with the printing rate, whereas it decreased for the present system when the flow-balance became sensitive to drop spacing.     

Simple and cost-effective reduction of graphite oxide by sulfuric acid

We report a simple, cost-effective, and environmentally benign process for reducing graphite oxide by treating solely with sulfuric acid. The suggested process consists of a two-step reduction of graphite oxide, first in aqueous sulfuric acid at room temperature and then in concentrated sulfuric acid with refluxing. X-ray diffractometry, X-ray photoelectron spectroscopy, Raman spectroscopy and thermogravimetric analysis demonstrated that the graphite oxide was reduced effectively and was comparable in composition to reduced graphite oxide prepared using previously described methods that rely on toxic and hazardous reducing agents, such as hydrazine, sodium borohydride, or hydrohalic acids.     

High‐Precision Temperature‐Controllable Metal‐Coated Polymeric Molds for Programmable,Hierarchical Patterning

Nanofabrication is an indispensable process in nanoscience and nanotechnology. Unconventional lithographic techniques are often used for fabrication as alternatives to photolithography because they are faster, more cost‐effective, and simpler to use. However, these techniques are limited in scalability and utility because of the collapse of preprinted structures during step‐and‐repeat processes. This study proposes a new class of temperature‐controllable polymeric molds that are coated with a metal such that any site‐specific patterning can be accomplished in a programmable manner using selective contact‐dewetting lithography. The lithography allows sub‐100 nm patterning, step‐and‐repeat processing, and hierarchical structure fabrication. The programmable feature of the lithography can be utilized for the structural coloring and shaping of objects. Large‐area programmable patterning, semiconductor device manufacturing, and the fabrication of iridescent security devices would benefit from the unique features of the proposed strategy.     

Steam reforming of liquefied natural gas (LNG) for hydrogen production over nickel–boron–alumina xerogel catalyst

A series of mesoporous nickel–boron–alumina xerogel (x-NBA) catalysts with different boron/nickel molar ratio (x = 0–1) were prepared by an epoxide-driven sol–gel method. The effect of boron/nickel molar ratio on the catalytic activities and physicochemical properties of nickel–boron–alumina xerogel catalysts was investigated in the steam reforming of liquefied natural gas (LNG). All the mesoporous x-NBA catalysts showed similar surface area. Introduction of boron increased interaction between nickel and support. In addition, introduction of boron into x-NBA catalysts reduced methane activation energy and increased nickel surface area. Promotion of boron had a positive effect on the catalytic activity due to the increase of adsorbed methane and nickel surface area. The amount of adsorbed methane and nickel surface area exhibited volcano-shaped trends with respect to boron/nickel molar ratio. LNG conversion and hydrogen yield increased with increasing the amount of adsorbed methane and with increasing nickel surface area. Among the catalysts, 0.3-NBA, which retained the largest amount of adsorbed methane and the highest nickel surface area, showed the best catalytic performance. It was also revealed that x-NBA catalysts showed strong coke resistance during the steam reforming reaction.