Influence of bearing damping on instability of asymmetric shafts, part IV: Effects of fluid-film bearings

The influence of fluid-film bearings on the parametric instability of asymmetric shafts is investigated. Since fluid-film bearings may have non-isotropic stiffness and damping, the system equations are time-varying coefficients in a rotating reference frame and the complete solution of transition curves includes coupled modes. Thus, the analytical modal method provided by our previous studies has been modified in this part for the determination of approximate solutions from a truncated Hill's determinant. In numerical examples, a plain cylindrical type and a tilting four-pad type are considered to estimate the effects of bearing parameters concerning static load, oil viscosity, and clearance on unstable regions.     

Field and numerical analysis of in-situ air sparging: a case study

An in-situ air sparging operation was used to remediate the sandy subsurface soils and shallow groundwater under a drum storage site near Chicago, IL, where either periodic or random spillage of a light non-aqueous phase liquid (LNAPL) occurred between 1980 and 1987. Both field measurements and model simulations using commercially available computer software suggested that microbial degradation was the most significant contributor to the removal of contaminant mass. Toluene, ethylbenzene and total xylenes (TEX), which were of major concern with regards to reaching clean-up criteria at the site, were observed to decline by 88% in concentration. Furthermore, up to 97% of the total mass removed through microbial degradation consisted of TEX. Of the total contaminant spill, up to 23% of initial organic chemical mass was removed through microbial degradation compared to less than 6% by physical stripping. Greater loss to microbial degradation is most likely attributed to the relatively low air injection rate used during the course of the air sparging remediation. Evaluation of air sparging at the site using model simulations supported this analysis by estimating 140 and 620 kg of total contaminant mass being removed through volatilization and biodegradation, respectively. An evaluation of several system design parameters using model simulations suggested that only the type of sparging operation (i.e. pulsed or continuous) was significant in terms of total contaminant removal time, while both the sparging operation and air injection rate were significant in terms of removal of a critical species, total xylenes.     

Bioinformatics of Differentially Expressed Genes in Phorbol 12-Myristate 13-Acetate-Induced Megakaryocytic Differentiation of K562 Cells by Microarray Analysis

Megakaryocytes are large hematopoietic cells present in the bone marrow cavity, comprising less than 0.1% of all bone marrow cells. Despite their small number, megakaryocytes play important roles in blood coagulation, inflammatory responses, and platelet production. However, little is known about changes in gene expression during megakaryocyte maturation. Here we identified the genes whose expression was changed during K562 leukemia cell differentiation into megakaryocytes using an Affymetrix GeneChip microarray to determine the multifunctionality of megakaryocytes. K562 cells were differentiated into mature megakaryocytes by treatment for 7 days with phorbol 12-myristate 13-acetate, and a microarray was performed using RNA obtained from both types of cells. The expression of 44,629 genes was compared between K562 cells and mature megakaryocytes, and 954 differentially expressed genes (DEGs) were selected based on a p-value < 0.05 and a fold change >2. The DEGs was further functionally classified using five major megakaryocyte function-associated clusters—inflammatory response, angiogenesis, cell migration, extracellular matrix, and secretion. Furthermore, interaction analysis based on the STRING database was used to generate interactions between the proteins translated from the DEGs. This study provides information on the bioinformatics of the DEGs in mature megakaryocytes after K562 cell differentiation.     

Shock Initiation of PBX-9404 by electrically driven flyer plates

The shock initiation threshold of PBX-9404 has been studied over the pressure range 3.1 GPa-28 GPa with pulse lengths ranging from 0.007 μs-0.63 μs. The short-duration, high pressure pulses were produced by the impact of thin plastic flyer plates accelerated by electrically exploded metal foils. We performed the experiments on explosive pellets 25.4 mm in diameter with thicknesses of 6.0 mm, 10.1 mm and 19.1 mm. No dependence of the initiation threshold on pellet thickness was observed. The data are represented reasonably well by either the critical initiation energy or by the constant P²τ initiation criteria.     

Effect of surface structure on biomechanical properties and osseointegration

The purpose of this study is to improve the bone-bonding ability between titanium implants and living bone through the control of geometric design and chemical compositions of an implant surface. We compared the tissue healing response and resulting implant stability for three surface designs by characterizing the histological and mechanical properties of the healing tissue around smooth-surfaced Ti–6Al–4V (SS), CP-Ti plasma-spray-coated (PSC), alkali- and heat-treated (AHT) implants. The implants were transversely inserted into a dog thighbone and evaluated at 4, 8, and 12 weeks. Histological examination indicated that initial matrix mineralization leading to osseointegration occurred more rapidly with the AHT implant. During the 4, 8, and 12 week healing periods, new bone on the surface of AHT implant showed denser growth than that on the SS and PSC implants. The more extensive tissue integration and more rapid matrix mineralization with the AHT implant were reflected in the mechanical test data, which demonstrated superior attachment strength and interfacial stiffness for the AHT implant after healing for 4, 8 and 12 weeks of healing because of the mechanical interlocking in the micrometer sized rough surface and the large bonding area between bone and implant caused by the nanosized porous surface structure. Histological and mechanical data demonstrate that with the appropriate surface design selection, bone bone-bonding ability can be improved and can induce acceleration of the healing response, thereby improving the potential for implant osseointegration.     

Amyloid Formation in Nanoliter Droplets

Processes that monitor the nucleation of amyloids and characterize the formation of amyloid fibrils are vital to medicine and pharmacology. In this study, we observe the nucleation and formation of lysozyme amyloid fibrils using a facile microfluidic system to generate nanoliter droplets that can control the flow rate and movement of monomer-in-oil emulsion droplets in a T-junction microchannel. Using a fluorescence assay, we monitor the nucleation and growth process of amyloids based on the volume of droplets. Using the microfluidic system, we demonstrate that the lag phase, which is vital to amyloid nucleation and growth, is reduced at a lower droplet volume. Furthermore, we report a peculiar phenomenon of high amyloid formation at the edge of a bullet-shaped droplet, which is likely due to the high local monomer concentration. Moreover, we discovered that amyloid fibrils synthesized in the nanoliter droplets are shorter and thicker than fibrils synthesized from a bulk solution via the conventional heating method. Herein, a facile procedure to observe and characterize the nucleation and growth of amyloid fibrils using nanoliter droplets is presented, which is beneficial for investigating new features of amyloid fibril formation as an unconventional synthetic method for amyloid fibrils.     

Heat-Killed Enterococcus faecalis EF-2001 Induces Human Dermal Papilla Cell Proliferation and Hair Regrowth in C57BL/6 Mice

Minoxidil is the most widely used treatment for hair growth, but has been associated with several side effects. In this study, we investigated the effects of heat-killed Enterococcus faecalis EF-2001 on hair loss prevention and regrowth using human dermal papilla cells and male C57BL/6 mice. To examine the effects of EF-2001, we used minoxidil as the positive control. In the in vitro experiments, EF-2001 treatment (75–500 μg/mL) led to the proliferation of human dermal papilla cells in a concentration-dependent manner. In the in vivo experiment, the topical application of 200 µL EF-2001 on the dorsal surface of C57BL/6 male mice led to hair growth. Changes in hair regrowth were examined by visual comparison and hematoxylin and eosin staining of skin sections. We also determined the expression levels of marker genes (Wnt) and growth factors (fibroblast growth factor, insulin growth factor 1, and vascular endothelial growth factor) in the skin tissues of the back of each mouse using a quantitative polymerase chain reaction. EF-2001 accelerated the progression of hair regrowth in mice and promoted hair-follicle conversion from telogen to anagen, likely by increasing the expression levels of growth factors and marker genes.     

Biomimetic micropatterning of silica by surface-initiated polymerization and microcontact printing

Micropatterns of silica on a gold substrate were generated by a biomimetic approach, namely, the biosilicification of silicic acids. The procedure consists of three simple steps: pattern generation of a polymerization initiator, (BrC(CH(3))(2)COO(CH(2))(11)S)(2), by microcontact printing; surface-initiated, atom-transfer radical polymerization of 2-(dimethylamino)ethyl methacrylate (DMAEMA) from the patterned area; and polycondensation of silicic acids. The tertiary amine-containing polymer, pDMAEMA, aided in the spatially controlled polycondensation of silicic acids on surfaces in the presence of phosphate ions, and micropatterns of silica on a gold substrate were successfully generated in combination with the technique of microcontact printing. The procedure could be extended to the controlled fabrication of silica patterns with any size, shape, or thickness.     

Mixture equations of state: Composition dependence

This paper discusses theoretical models for the composition dependence of equations of state and compares the quality of predictions against experimental thermodynamic property data. The mean density approximation (MDA) and the van der Waals one-fluid (VDW1) model are compared with hybrid mixing rules (HMR), in which rigorous composition dependence is used for the second and third virial coefficients and the conformai solution model is used for equation-of-state density terms beyond the third virial term. It is found that when values of unity are used for all binary and three-body unlike interaction parameters, calculated densities for methane-normal heptane mixtures have average absolute deviations of 3.54% for MDA, 4.04% for VDW1, and 2.59% for HMR. When vapor-liquid equilibrium calculations were performed for the methane-normal heptane system, average absolute deviations of calculatedK values from experimental values were 16.7% for methane and 36.4% for normal heptane using HMR, whereas when conformal solution model (CSM) mixing rules were used, the results were 34.8% for methane and 66.7% for normal heptane. When the binary interaction parameter for the characterization of interaction energies is determined, it is found to be less sensitive to state conditions in the case of HMR than either MDA or VDW1. These preliminary results suggest the potential of mixture equation-of-state methods which utilize rigorous composition dependence for the lower-order virial coefficients.Paper presented at the Second U.S.-Japan Joint Seminar on Thermophysical Properties, June 23, 1988, Gaithersburg, Maryland, U.S.A.