Experimental and numerical assessment of gate-lag phenomena in AlGaAs-GaAs heterostructure field-effect transistors (FETs)

Gate-lag effects are characterized in AlGaAs-GaAs heterostructure field-effect transistors (HFETs) by means of measurements and numerical device simulations. Gate lag increasingly affects device switching at increasing ungated recess extension, suggesting that responsible deep levels be located at the ungated, recess surface of the HFET. Gate lag diminishes by making the off-state gate-source voltage less negative and by increasing the drain bias. Increasing the temperature makes the turn-on transient faster at low drain bias, while slightly delaying it at high drain bias. Numerical device simulations accounting for acceptor-like traps at the ungated surface predict gate-lag phenomena in good agreement with experiments, reproducing correctly the observed bias and temperature dependences. Simulations show that surface states behave, during the turn-on transient, as hole traps capturing holes attracted at the ungated surface by the negative trapped charge.     

A power-driven multiplication instruction-set design method for ASIPs

This paper presents a novel power-driven multiplication instruction-set design method for application-specific instruction-set processors (ASIPs). Based on a dual-and-configurable-multiplier structure, our proposed method devises a multiplication instruction set for low-power ASIPs. Our method exploits the execution sequences of multiplication instructions and effective bit widths of variables to reduce power consumed by redundant multiplication bits while minimizing the multiplication execution time. Experimental results on a set of DSP programs demonstrate that our proposed method achieves significant power reduction (up to 18.53%) and execution time improvement (up to 10.43%) with 18% area overhead.     

Co-digestion of manure and biowaste according to the EC animal by-products regulation and Finnish national regulations.

The objective of this study was to compare methane production and characteristics of digested material in anaerobic digestion concepts according to the Animal By-Products Regulation (ABP-Regulation) of the EC (hygienisation of biowaste for 1 hour at 70 degrees C, particle size < 12 mm) and Finnish national regulations (treatment temperature 55 degrees C, feeding interval 24 h, hydraulic retention time (HRT) 20 d, particle size < 40 mm) and with small variations in treatment methods for treating manure and biowaste. Moreover, the survival of three different salmonella bacteria in these processes was studied. Hygienisation of biowaste prior to digestion at 35 degrees C enhanced methane production by 14-18% compared to similar treatment without hygienisation. The differences in treatment temperature, HRT and hygienisation of biowaste prior to digestion did not significantly affect the characteristics of digested material. The concepts according to the ABP-Regulation and Finnish national regulations were effective in destroying salmonella bacteria to an undetectable level.     

Performance of thermostatic and electronic valves controlling the compressor capacity

The performance of the energy consumption of an electronic valve and a classical thermostatic valve has been compared when these expansion valves are adopted in a vapour compression plant subjected to a cold store. The main aim is to verify experimentally which type of expansion valve would be preferable from energy point of view when a classical thermostat or a fuzzy logic algorithm are used as the control system for the refrigeration capacity. The fuzzy logic‐based control is able to modulate continuously the compressor speed through an inverter. The results show that with a fuzzy algorithm, the thermostatic expansion valve allows an energy saving of about 8% in comparison with the electronic valve. When on–off control is used, the electric energy consumption obtained both with the electronic valve and with the thermostatic valve is comparable. Copyright © 2006 John Wiley & Sons, Ltd.     

Dominant rock properties affecting the performance of conical picks and the comparison of some experimental and theoretical results

Conical picks are the essential cutting tools used especially on roadheaders, continuous miners and shearers and their cutting performance affects directly the efficiency and the cost of rock/mineral excavation. In this study, in order to better understand the effects of dominant rock properties on cutter performance, 22 different rock specimens having compressive strength values varying from 10 to 170 MPa are first subjected to a wide range of mechanical tests. Then, laboratory full-scale linear cutting tests with different depth of cut and cutter spacing values are realized on large blocks of rock specimens using one type of conical pick. Specific energy, cutting and normal force values for relieved and unrelieved cutting modes are recorded using a triaxial force dynamometer with capacity of 50 tonnes and a data acquisition system. Cutter force and specific energy values are correlated with rock properties and theoretical force and specific energy values obtained from widely used theoretical approaches.The results indicate that uniaxial compressive strength among the rock properties investigated is best correlated with the measured cutter performance values, which is in good agreement with previous studies. However, it is also emphasized in this study that Brazilian tensile strength, Schmidt hammer rebound values, static and dynamic elasticity modulus are also dominant rock properties affecting cutter performance.Theoretical specific energy defined by different researchers has a meaningful relationship with the experimental specific energy, which is an essential parameter for predicting the instantaneous cutting rates of mechanical excavation systems. It is also demonstrated that the experimental cutter forces obtained for 5 mm depth of cut are in good agreement with theoretical force values, if the friction angle between rock and cutting tool is included in the theoretical formulation. It is emphasized that, to some extend, laboratory tests can help to minimize high cost of a trial–error approach in the field.     

Catalytic aminolysis of epoxide by alumina prepared from amine-protected Al precursor

The catalytic activities of alumina prepared from an Al alkoxide-amine adduct monomer for the reaction of cyclopentene oxide with piperidine was determined after various pretreatments, including calcination and exposure to moisture. They were compared with the activity of alumina prepared by the conventional hydrolysis method. It was found that the as-prepared sample from the alkoxide-amine monomer preparation was five times more active than a conventional preparation, suggesting that it has a higher density of surface Lewis acid sites. However, its activity was much more severely suppressed by exposure to moisture.     

On Faster I DDQ Measurements

The purpose of this paper is to introduce a new I _DDQ measurement technique based on active successive approximations, called ASA-I _DDQ. This technique has unique features facilitating a speed-up in I _DDQ measurement. Experimental results suggest that a significant speed-up factor (up to 4) can be obtained over the QuiC-Mon technique. Such a speed-up is a key element in the replacement of single-threshold I _DDQ testing since it amplifies the effectiveness of post-processing techniques.     

Analysis of an extensive measurement program developed from the start up to the follow up of the operation of the CNAAA NPP

Integrated tests (IT) applied to the Units I and II of the CNAAA Nuclear Power Plants (Angra dos Reis, Rio de Janeiro, Brazil) vara part of a comprehensive test program required to have the commercial operational licence issued. The IT cover operation at zero power and the subsequent power levels (the power escalation) until the nominal power operation.

This paper reports and compares the results of systematic neutron and gamma equivalent dose-rate measurements performed inside and outside the reactor containment of each Unit, during the start-up phase of the operation, for different power levels of the reactors. It also compares the collective-doses measured along the operation of the two units of the CNAAA wich similar data of the Grafenrheinfeld nuclear power plant (Germany) — basic-of-project for the CNAAA — Unit II — and analyses the data under the fight of the state-of-art.     

On-demand learning for a wireless campus

The current Internet and wireless networks are harsh environments for transporting high-bandwidth multimedia data. We examine the technical issues involved, and describe an end-to-end solution to support a Web-based learn-on-demand system that operates in a wireless campus environment.