Wear in check valves due to flow induced motion

Experiments showing the frequency and amplitude of the flow induced motion of the gate for a 2- and a 4-in. swing check valve have been performed. The gate motion is due to turbulence in approach flow. We have found the dominant turbulent frequency of the approach flow is about half the natural frequency of the valves. The valves appear to be almost critically damped. Because of this, the valves respond almost as they would to a static force of the magnitude characteristic of the turbulent fluctuation in the flow. Both the dimensionless exciting force and the damping ratio have been found to be independent of valve size so the above statements are true for larger valves also. The recommended valve oscillation amplitudes and frequencies are used to calculate the wear at the shaft and at the stop. For an unpegged check valve, such as one of the 10-in. valves which was used at the San Onofre Nuclear Generation Station, it was found that shaft bearing wear would amount to 0.27 in.³/year and stop wear to 0.03 in.³/year.     

A systematic techno-economic assessment of a WEC system installation for low-cost electrification of a habitable dwelling

This paper deals with the technical feasibility and economic viability of a grid connected wind-energy conversion system (WECS) used to cover the energy demand of an average habitable dwelling. The various parts of the wind-energy system are described and the useful electrical energy production is determined using a simulation program based on the Monte Carlo method. An economic analysis of the WEC system is performed using a computerized assessment tool. Important financial indices are calculated and financial scenarios investigated.     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

Security issues for downloaded code in mobile phones

'Software defined radio' (SDR) is a technology that will appear in future generations of mobile phones, i.e. following the third-generation mobile phone technology that is currently being defined and developed. Early versions of 'pragmatic' SDR will allow the terminal to be reconfigured at any level of its protocol stack. Ultimately, the 'pure' SDR technology will allow a mobile phone or terminal to have its air interface software configured or reconfigured by other software (or software parameters) that have been downloaded to the terminal, e.g. over the air, or from a remote server via the Internet and one's personal computer (PC). A number of security issues arise with downloaded code that implements the air interface functions, and these may not be obvious simply from looking at the way PC software is updated on-line today. This paper starts with an outline of the code that allows a mobile phone to operate over a particular air interface. This sets the baseline for a discussion of the security issues surrounding the change of this code from one that is fixed and downloaded once only, to code that is reconfigurable during the life of a product.     

Sequential tripping strategy for a transmission network back-upprotection expert system

This paper describes a sequential tripping strategy used in a wide area back-up protection expert system (BPES) to combat situations in which protection relays have maloperated or information is missing. The BPES is an innovative back-up protection scheme designed to prevent the occurrence of widespread blackouts. The BPES evaluates the certainty that transmission lines are likely to be affected by the fault and uses a sequential tripping strategy to isolate the fault if a firm decision is not available due to maloperated relays and/or missing information. The mode of analysis and the sequential tripping strategy ensures that the BPES will clear a fault at minimum risk to the network. An example is included to demonstrate how the certainty factor based sequential tripping strategy is employed by the BPES to clear a fault which occurred on the South Western part of the UK National Grid System     

PCR-based procedures in detection and DNA-fingerprinting of Salmonella from samples of animal origin

The usefulness of selected PCR-protocols for the detection of Salmonella in 117 samples of animal origin (17 raw minced meat, 27 raw chicken meat, 8 raw sausages, and 25 egg samples, as well as 18 poultry faecal, and caecal swabs samples) and DNA-fingerprinting typing is shown. To establish an accurate PCR-procedure for Salmonella detection the following parameters were evaluated: two pre-PCR concentration procedures, centrifugation and immunomagnetic separation (IMS) using Dynabeads anti- Salmonella; the specificity and sensitivity of 10 sets of primers; and different conditions of the amplification reaction. In light of the results obtained from the use of PCR-based procedures alone or in combination with conventional methods, the following findings can be underlined: First, IMS is more efficient than centrifugation in the recovery of Salmonella. Second, the selected IMS/PCR-detection protocol is less time-consuming (45 h) than the IMS/culture procedure (90 h), and a good concordance between them was found when the Kappa coefficient was calculated (0·87). Third, PCR-ribotyping technique showed a very low discrimination power, being able to differentiate only three profiles. Fourth, RAPD technique using specific primers supports previous works in which it was proposed as a simple and useful tool for discriminating isolates between and within serotypes. Fifth, The efficiency, rapidity, and flexibility of the PCR-protocols applied were high, and they can be performed using two PCR-programs and the same basic equipment.