Radiometric sensor for temperature control of food processing

This paper describes a novel planar antenna sensor created for the purpose of noninvasive temperature measurements using microwave radiometry. In order to improve radiometric measurements in industrial applications, a new generation of sensors is introduced, composed of a metallic sheet. Simulations based upon the method of moments is used both to design and to determine their electromagnetic performances. This paper also describes a radiometric device using these sensors to measure and control the temperature of food products during deep freezing processes. The results and discussions are presented.     

Switched-Current Filters Revisited: Square-Root Domain Sampled-Data Filters

In this brief, the well-known switched-current (SI) filtering technique is revisited using the concept of the square-root domain (SRD) filtering. It is proved that SI filters are a subclass of the SRD filters, where sampled-data signal processing is performed. This is achieved by considering typical lossless and lossy SRD sampled-data integrator configurations, using a set of complementary SRD operators which are based on the quadratic I-V relationship of MOS transistor operated in the saturation. Circuit examples are given, where linear-domain integrator and third-order filter configurations were derived using appropriate SRD sampled-data building blocks     

Parametric effects on the transient Voltage performance of a DC superconducting cable

The objective of this work was to determine the significant parameters of a 3-GW 200-kV dc superconducting cable system which influence the transient voltage distribution in the various parts of the cable. The cable system consists of four coaxial metallic cylinders. It was found that the dielectric constant and the electrical resistivity of the soil significantly affect the severity of the transient voltages; lower dielectric constant and higher resistivity of the soil will increase the magnitudes of the transient voltages by increasing the earth-return impedance. It was also found that the effect of the conductor internal impedances of the cable is insignificant. Shorting the coaxial cylinders of the cryogen flow and the cryostat will lessen the severity of the transient voltages. Grounding the second, third, and fourth cylinders at regular intervals with low-impedance grounding impedance will also improve the transient performance of the cable. More research is needed to evaluate these procedures.     

Fracture response of fibre-reinforced materials with macro/microcrack damage using the Boundary Element Technique

The Boundary Element Method (BEM) incorporating the Embedded Cell Approach (ECA) has been used to analyse the effects of constituent material properties, fibre spatial distribution and microcrack damage on the localised behaviour of transversely fractured, unidirectional fibre-reinforced composites. Three specific composites, i.e., glass fibre reinforced polyester, carbon fibre reinforced epoxy and a glass-carbon hybrid, are considered. The geometrical structures examined were perfectly periodic, uniformly spaced fibre arrangements in square and hexagonal embedded cells. In addition, numerical simulations were also conducted using embedded cells containing randomly distributed fibres. The models involve both elastic fibres and matrix, with the interfaces between the different phases being fully bonded. The results indicate that the constituent material properties (two phase composite) and spatial distribution have a significant effect on the localised stress distributions around the primary crack tip. However, the strain energy release rate associated with crack propagation is predominantly influenced by the material composition. The three-phase hybrid composite exhibited an apparent intermediate fracture toughness value, compared to the all-glass and all-carbon models. Furthermore, the strain energy release rate for the macrocrack lowers as it enters a zone of localised damage (microcracking). The presence of microcracks relaxes the stress field, which can result in a significant reduction in the energetics of the primary crack.     

Surface effects in nanocrystalline silicon

Exposure to ammonia (NH₃) increases the dark current (DC) in nanocrystalline silicon. Light soaking (LS) for short periods also enhances the dark current, which remains at a high value for a long time. Pumping alone is unable to restore the initial annealed state, but annealing brings it back. The final state obtained by LS and NH₃ exposure depends on the order in which they are performed. Evaporated selenium (Se) deposited on nanocrystalline silicon decreases the DC. These effects cannot be explained entirely by the presence of a-Si : H alone, in our sample. DC and photoluminescence (PL) measurements indicate the presence of two types of center in our sample, which behave differently when exposed to NH₃.     

Intelligent process analytics for CRM

Many organisations use decision models in their processes such as tables or trees to provide decision support to their operational divisions. For example, in fault management, customer contact centre operators usually use a decision model in the form of prescribed interviews. Based on the answers given by customers, the operator navigates through the decision model to reach an assessment of the problem. In order to achieve customer satisfaction and operational excellence, it is very important to constantly monitor the performance of a decision model not only on an overall level, but also on the level of individual decisions. In this paper we present a configurable business process analytics tool, known as the intelligent Universal Service Management System, that constantly monitors decision data and is capable of optimising the decisions based on high-level business objectives. We explain the various features of the software and show how it can be used to optimise decision processes. We also show how we can easily provide a customised version to monitor the performance of provision processes.     

Profile-Driven Component Placement for Cluster-Based Online Services

The growth of the Internet and of various intranets has spawned a wealth of online services, most of which are implemented on local-area clusters using remote invocation (for example, remote procedure call/remote method invocation) among manually placed application components. Component placement can be a significant challenge for large-scale services, particularly when application resource needs are workload dependent. Automatic component placement has the potential to maximize overall system throughput. The key idea is to construct (offline) a mapping between input workload and individual-component resource consumption. Such mappings, called component profiles, then support high-performance placement. Preliminary results on an online auction benchmark based on J2EE (Java 2 Platform, Enterprise Edition) suggest that profile-driven tools can identify placements that achieve near-optimal overall throughput.