Improved method for roadside barrier length of need modeling using real-world trajectories

The 2011 AASHTO Roadside Design Guide (RDG) contains perhaps the most widely used procedure for choosing an appropriate length of need (LON) for roadside barriers. However, this procedure has several limitations. The procedure uses a highly simplified model of vehicle departure, and the procedure does not allow designers to specify an explicit level of protection. A new procedure for choosing LON that addresses these limitations is presented in this paper. This new procedure is based on recent, real-world road departure trajectories and uses this departure data in a more realistic way. The new procedure also allows LON to be specified for a precisely known level of protection – a level which can be based on number of crashes, injury outcomes or even estimated crash cost – while still remaining straightforward and quick to use like the 2011 RDG procedure.     

Annular‐ring slot antenna designs with circular polarization radiation

The design of a microstrip‐fed annular‐ring slot antenna (ARSA) with circular polarization (CP) radiation is initially studied. To obtain CP radiation with broad 3‐dB axial ratio (AR) bandwidth that can cover the WiMAX 2.3 GHz (2305–2320 MHz, 2345–2360 MHz) and WLAN 2.4 GHz (2400–2480 MHz) bands, a novel technique of extending an inverted L‐shaped slot from the bottom section of the annular‐ring is proposed. To suppress the harmonic modes induced by the CP ARSA, the technique of integrating a defected ground structure into the annular‐ring slot is further introduced. From the measured results, 10‐dB impedance bandwidth and 3‐dB AR bandwidth of 44.86 and 9.68% were achieved by the proposed harmonic suppressed CP ARSA. Furthermore, average gain and radiation efficiency of ～4.7 dBic and 71%, respectively, were also exhibited across the bands of interest. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:337–345, 2015.     

Sex and Depot Differences in Palmitoleic Acid Content of Human Blood and Fat

Palmitoleic acid has been classified as an insulin-sensitizing lipokine, but evidence for this from human studies has been inconsistent. We hypothesized that this is related to either the types of samples or conditions under which samples are collected. We measured plasma palmitoleic acid and total free fatty acids (FFA) using ultra-performance liquid chromatography in blood samples collected from 34 adults under a variety of conditions. We collected duplicate samples of adipose (n = 10), FFA (n = 9), and very low density lipoprotein triacylglycerol (VLDL-TAG) (n = 7) to measure the palmitoleic acid as a percentage of total fatty acids. We tested whether the percentage of palmitoleic acid was correlated with insulin resistance, as measured by homeostatic model of insulin resistance (HOMA-IR). Adipose stearoyl-coenzyme A desaturase 1 (SCD-1) protein was measured by capillary Western blotting. FFA-palmitoleic acid percentage increased as a function of total FFA and was greater (p < 0.005) in females than males. Adipose palmitoleic acid percentage was greater in females than males (p < 0.001), as was adipose SCD-1. Palmitoleic acid was greater in femoral fat than in abdominal fat in both females and males (p < 0.001), and correlated positively with HOMA-IR only in females. The test–retest reliability values for percentage palmitoleic acid were 7 ± 10% for adipose, 24 ± 26% for VLDL, and 53 ± 31% for FFA. Because FFA-palmitoleic acid percentage varies as a function of total FFA, investigators should re-evaluate how palmitoleic acid data is presented. The positive relationship between adipose palmitoleic acid and HOMA-IR in females suggests that it is not a potent insulin-sensitizing lipokine in humans.     

Fully renewable limonene‐derived polycarbonate as a high‐performance alkyd resin

Limonene‐derived polycarbonate‐based alkyd resins (ARs) have been prepared by copolymerization of limonene dioxide with CO₂, catalysed by a β‐diiminate zinc–bis(trimethylsilyl)amido complex, and subsequent chemical modification with soybean oil fatty acids using triphenylethylphosphonium bromide as the catalyst. This quantitative partial modification was realized via epoxy–carboxylic acid chemistry, affording ARs with higher oil lengths, lower polydispersities and higher glass transition temperatures (T_g) in comparison to a conventional polyester AR based on phthalic acid, multifunctional polyol pentaerythritol and soybean fatty acid. The novel limonene polycarbonate AR and the conventional polyester AR were evaluated as coatings and both the physical drying (without the presence of the oxidative drying accelerator Borchi® Oxy Coat) and chemical curing (with Borchi® Oxy Coat) processes of these coatings were monitored by measuring the König hardness and complex modulus development with time. A better performance was obtained for the alkyd paint containing polycarbonates modified with fatty acids (FA‐PCs), which showed a faster chemical drying, a higher König hardness and a higher T_g in coating evaluation, demonstrating that the fully renewable FA‐PCs are promising resins for alkyd paint applications. © 2019 Society of Chemical Industry     

Towards optimization of the osmotic drying process of alumina-gelatin objects: Regression analysis and verification

In this study, further analysis of the osmotic drying process was conducted to identify the optimum combination of parameters for drying rectangular alumina-gelatin beams. This study was designed to determine the effect of three variables related to the osmotic drying process (osmotic pressure, molecular weight, and immersion time) on the interaction between the liquid desiccant and the submerged alumina-gelatin samples. The water loss from the alumina-gelatin samples was positively correlated with the molecular weight, osmotic pressure, and immersion time. Up to 40% by weight of the initial water content was removed during the osmotic drying process. The samples also experienced solids gain due to the counterflow of solute from the liquid desiccant. The least amount of solids gain resulted from drying for the shortest immersion time at low osmotic pressure and high molecular weight. Evidence of possible interactions between variables was noted for the sintered density metric. Statistical methods were used to form regression equations for the measured responses (water loss, solids gain, bulk density). A verification experiment was conducted to compare the experimental outcomes to the predicted outcomes. The responses were simultaneously optimized to identify the combination of variable settings required to meet specified goals. In order to maximize water loss, minimize solids gain, and maximize bulk density, the ceramic-gelatin object should be immersed for approximately 60?min in an aqueous solution of 100,000?g/mol poly(ethylene oxide) at an osmotic pressure of 2.50?MPa. These values are valid for the range of parameter settings tested and the sample fabrication and drying methods used.